ISO 3723:2015
(Main)Hydraulic fluid power — Filter elements — Method for end load test
Hydraulic fluid power — Filter elements — Method for end load test
ISO 3723:2015 specifies a method for verifying the end load rating of a hydraulic fluid power filter element. It also verifies the ability of a hydraulic fluid power filter element to withstand the designated axial loading imposed by installation and use.
Transmissions hydrauliques — Éléments filtrants — Méthode de détermination de la résistance à la déformation axiale
L'ISO 3723:2015 spécifie une méthode de contrôle de la charge axiale nominale des éléments filtrants des systèmes de transmissions hydrauliques. Cette méthode permet également de contrôler l'aptitude de ces éléments filtrants à résister à la charge axiale spécifiée qui est due aux conditions d'installation et d'utilisation.
Fluidna tehnika - Hidravlika - Filtrski vložki - Metoda končnega obremenilnega preskusa
Ta mednarodni standard določa metodo za preverjanje končne obremenilne vrednosti filtrirnega elementa v hidravličnem pogonskem sistemu. Opredeljuje tudi način preverjanja zmožnosti filtrirnega elementa v hidravličnem pogonskem sistemu za prenašanje določene osne obtežitve zaradi namestitve in uporabe.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 3723
Second edition
2015-05-15
Hydraulic fluid power — Filter
elements — Method for end load test
Transmissions hydrauliques — Éléments filtrants — Méthode de
détermination de la résistance à la déformation axiale
Reference number
ISO 3723:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 3723:2015(E)
IMPORTANT — PLEASE NOTE
This is a mark-up copy and uses the following colour coding:
Text example 1 — indicates added text (in green)
Text example 2 — indicates removed text (in red)
— indicates added graphic figure
— indicates removed graphic figure
1.x . — Heading numbers containg modifications are highlighted in yellow in
the Table of Contents
All changes in this document have yet to reach concensus by vote and as such should only
be used internally for review purposes.
DISCLAIMER
This Redline version provides you with a quick and easy way to compare the main changes
between this edition of the standard and its previous edition. It doesn’t capture all single
changes such as punctuation but highlights the modifications providing customers with
the most valuable information. Therefore it is important to note that this Redline version is
not the official ISO standard and that the users must consult with the clean version of the
standard, which is the official standard, for implementation purposes.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3723:2015(E)
Contents Page
Foreword .iv
Introduction .v
0 INTRODUCTION . 1
1 SCOPE AND FIELD OF APPLICATION Scope . 1
2 REFERENCES Normative references . 1
3 DEFINITIONS Terms and definitions. 1
4 Test equipment. 1
5 Test procedure . 2
6 Criteria for acceptance . 2
7 IDENTIFICATION STATEMENT Identification statement(Reference to this
International Standard) . 2
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 3723:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
institutesbodies (ISO member bodies). The work of developingpreparing International Standards is
normally carried out through ISO Technical Committees. Every Member Bodytechnical committees.
Each member body interested in a subject for which a technical committee has been set upestablished
has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Draft International Standards adopted by the Technical Committees are circulated to the Member
Bodies for approval before their acce
...
INTERNATIONAL ISO
STANDARD 3723
Second edition
2015-05-15
Hydraulic fluid power — Filter
elements — Method for end load test
Transmissions hydrauliques — Éléments filtrants — Méthode de
détermination de la résistance à la déformation axiale
Reference number
ISO 3723:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 3723:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3723:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test equipment. 1
5 Test procedure . 1
6 Criteria for acceptance . 1
7 Identification statement . 2
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 3723:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibil
...
SLOVENSKI STANDARD
SIST ISO 3723:2016
01-maj-2016
1DGRPHãþD
SIST ISO 3723:1997
)OXLGQDWHKQLND+LGUDYOLND)LOWUVNLYORåNL0HWRGDNRQþQHJDREUHPHQLOQHJD
SUHVNXVD
Hydraulic fluid power - Filter elements - Method for end load test
Transmissions hydrauliques - Éléments filtrants - Méthode de détermination de la
résistance à la déformation axiale
Ta slovenski standard je istoveten z: ISO 3723:2015
ICS:
23.100.60 )LOWULWHVQLODLQ Filters, seals and
RQHVQDåHYDQMHWHNRþLQ contamination of fluids
SIST ISO 3723:2016 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 3723:2016
---------------------- Page: 2 ----------------------
SIST ISO 3723:2016
INTERNATIONAL ISO
STANDARD 3723
Second edition
2015-05-15
Hydraulic fluid power — Filter
elements — Method for end load test
Transmissions hydrauliques — Éléments filtrants — Méthode de
détermination de la résistance à la déformation axiale
Reference number
ISO 3723:2015(E)
©
ISO 2015
---------------------- Page: 3 ----------------------
SIST ISO 3723:2016
ISO 3723:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 3723:2016
ISO 3723:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test equipment. 1
5 Test procedure . 1
6 Criteria for acceptance . 1
7 Identification statement . 2
© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 3723:2016
ISO 3723:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardi
...
NORME ISO
INTERNATIONALE 3723
Deuxième édition
2015-05-15
Transmissions hydrauliques —
Éléments filtrants — Méthode de
détermination de la résistance à la
déformation axiale
Hydraulic fluid power — Filter elements — Method for end load test
Numéro de référence
ISO 3723:2015(F)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 3723:2015(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2015 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 3723:2015(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Équipement d’essai . 1
5 Mode opératoire d’essai. 1
6 Critères d’acceptation . 2
7 Phrase d’identification . 2
© ISO 2015 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 3723:2015(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de brevets reçues par
l’ISO (voir www.iso.org/brevets).
L
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.