iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 3320:2013

(Main)

Fluid power systems and components — Cylinder bores and piston rod diameters and area ratios — Metric series

Fluid power systems and components — Cylinder bores and piston rod diameters and area ratios — Metric series

ISO 3320:2013 establishes a metric series of cylinder bore and piston rod diameters for hydraulic and pneumatic cylinders, and specifies for each pair of diameters a corresponding standard ratio between the useful areas. It applies only to the dimensional criteria of products manufactured in conformity with ISO 3320:2013; it does not apply to their functional characteristics.

Transmissions et composants hydrauliques et pneumatiques — Alésages des vérins et diamètres des tiges de piston et rapports de surface — Série métrique

L'ISO 3320:2013 établit une série métrique d'alésage de vérin et de diamètres de tige de piston pour vérins hydraulique et pneumatiques, et spécifie pour chaque paire de diamètres un rapport normalisé correspondant entre les zones utiles. Elle s'applique uniquement aux caractéristiques dimensionnelles des produits fabriqués en conformité avec celle-ci; elle ne s'applique pas à leurs caractéristiques fonctionnelles.

Fluidna tehnika - Premeri valjev in batnic ter razmerja delovnih ploščin - Metrska vrsta

General Information

Status
Published
Publication Date
01-Dec-2013
ICS
23.100.20 - Cylinders
Technical Committee
ISO/TC 131/SC 3 - Cylinders
Drafting Committee
ISO/TC 131/SC 3 - Cylinders
Current Stage
9060 - Close of review
Start Date
02-Sep-2029
Ref Project
SIST ISO 3320:2014 - Fluid power systems and components - Cylinder bores and piston rod diameters and area ratios - Metric series

Relations

Revises
ISO 3320:1987 - Fluid power systems and components — Cylinder bores and piston rod diameters — Metric series
Effective Date
10-Mar-2012
Revises
ISO 7181:1991 - Hydraulic fluid power — Cylinders — Bore and rod area ratios
Effective Date
10-Mar-2012

Buy Standard

ISO 3320:2013 - Fluid power systems and components -- Cylinder bores and piston rod diameters and area ratios -- Metric seriesISO 3320:2013 - Fluid power systems and components -- Cylinder bores and piston rod diameters and area ratios -- Metric series
PreviousNext
Standard
ISO 3320:2013 - Fluid power systems and components -- Cylinder bores and piston rod diameters and area ratios -- Metric series
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 3320:2014ISO 3320:2014
PreviousNext
Standard
ISO 3320:2014
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
ISO 3320:2013 - Transmissions et composants hydrauliques et pneumatiques -- Alésages des vérins et diametres des tiges de piston et rapports de surface -- Série métriqueISO 3320:2013 - Transmissions et composants hydrauliques et pneumatiques -- Alésages des vérins et diametres des tiges de piston et rapports de surface -- Série métrique
PreviousNext
Standard
ISO 3320:2013 - Transmissions et composants hydrauliques et pneumatiques -- Alésages des vérins et diametres des tiges de piston et rapports de surface -- Série métrique
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3320
Third edition
2013-12-01
Fluid power systems and
components — Cylinder bores and
piston rod diameters and area ratios
— Metric series
Transmissions et composants hydrauliques et pneumatiques —
Alésages des vérins et diamètres des tiges de piston et rapports de
surface — Série métrique
Reference number
ISO 3320:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 3320:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3320:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 Dimensions . 2
6 Area ratios . 3
7 Identification statement (reference to this International Standard) . 3
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3320:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Tr
...

SLOVENSKI STANDARD
SIST ISO 3320:2014
01-marec-2014
1DGRPHãþD
SIST ISO 3320:1995
SIST ISO 7181:1997
)OXLGQDWHKQLND3UHPHULYDOMHYLQEDWQLFWHUUD]PHUMDGHORYQLKSORãþLQ0HWUVND
YUVWD
Fluid power systems and components - Cylinder bores and piston rod diameters and
area ratios - Metric series
Transmissions et composants hydrauliques et pneumatiques - Alésages des vérins et
diamètres des tiges de piston et rapports de surface - Série métrique
Ta slovenski standard je istoveten z: ISO 3320:2013
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST ISO 3320:2014 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3320:2014

---------------------- Page: 2 ----------------------

SIST ISO 3320:2014
INTERNATIONAL ISO
STANDARD 3320
Third edition
2013-12-01
Fluid power systems and
components — Cylinder bores and
piston rod diameters and area ratios
— Metric series
Transmissions et composants hydrauliques et pneumatiques —
Alésages des vérins et diamètres des tiges de piston et rapports de
surface — Série métrique
Reference number
ISO 3320:2013(E)
©
ISO 2013

---------------------- Page: 3 ----------------------

SIST ISO 3320:2014
ISO 3320:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3320:2014
ISO 3320:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 Dimensions . 2
6 Area ratios . 3
7 Identification statement (reference to this International Standard) . 3
© ISO 2013 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 3320:2014
ISO 3320:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
differen
...

NORME ISO
INTERNATIONALE 3320
Troisième édition
2013-12-01
Transmissions et composants
hydrauliques et pneumatiques —
Alésages des vérins et diamètres des
tiges de piston et rapports de surface
— Série métrique
Fluid power systems and components — Cylinder bores and piston
rod diameters and area ratios — Metric series
Numéro de référence
ISO 3320:2013(F)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 3320:2013(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Version française parue en 2014
Publié en Suisse
ii © ISO 2013 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3320:2013(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles et unités . 1
5 Dimensions . 2
6 Rapport de surface . 3
7 Phase d’identification (référence à la présente Norme internationale) .3
© ISO 2013 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3320:2013(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/CEI, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/CEI, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou sur la liste ISO des déclarations de brevets reçues
(voir www.iso.org/patents).
Les éventuelles appellations commerciales utilisées dans le présent do
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 8133:2022(Main)
Hydraulic fluid power — Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series

This document specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020‑2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020‑2, but this does not limit their application[1]. This document covers the following accessories, identified in accordance with ISO 6099: — AP6 — rod eye spherical, female thread (see Figure 1 and Table 1); — AB5 — clevis bracket, spherical eye, in angle (see Figure 2 and Table 2); — AA6-L — pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3); — AL6 — locking plate for pivot pin (see Figure 4 and Table 4); — AP2 — rod clevis, female thread (see Figure 5 and Table 5); — AP4 — rod eye plain, female thread (see Figure 6 and Table 6); — AB2 — eye bracket (see Figure 7 and Table 7); — AB4 — clevis bracket, straight (see Figure 8 and Table 8); — AA4-S — pivot pin, plain (split pins) (see Figure 9 and Table 9); — AA4-R — pivot pin, plain (rings) (see Figure 10 and Table 10); — AT4 — trunnion bracket (see Figure 11 and Table 11). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944. This document only applies to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off
ISO
ISO 8132:2022(Main)
Hydraulic fluid power — Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series

This document specifies the mounting dimensions required for the interchangeability of accessories for 16 MPa (160 bar) medium series cylinders in accordance with ISO 6020‑1 and for 25 MPa (250 bar) series cylinders in accordance with ISO 6022. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020‑1 and ISO 6022, but this does not limit their application[1]. This document covers the following accessories, identified in accordance with ISO 6099: — AP2 — rod clevis, female thread (see Figure 1 and Table 1); — AF3 — rod flange, circular (see Figure 2 and Table 2); — AB4 — clevis bracket, straight (see Figure 3 and Table 3); — AB3 — clevis bracket, in angle (see Figure 4 and Table 4); — AT4 — trunnion bracket (see Figure 5 and Table 5); — AA4-R — pivot pin, plain bearing (snap ring type) (see Figure 6 and Table 6); — AA4-S — pivot pin, plain bearing (split pin type) (see Figure 7 and Table 7); — AA6-R — pivot pin, spherical bearing (snap ring type) (see Figure 6 and Table 6); — AA6-S — pivot pin, spherical bearing (split pin type) (see Figure 7 and Table 7); — AP6 — rod eye spherical, female thread (see Figure 8 and Table 8); — AP4 — rod eye plain, female thread (see Figure 9 and Table 9). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944. This document applies only to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
ISO
ISO/TS 13725:2021(Main)
Hydraulic fluid power — Method for evaluating the buckling load of a hydraulic cylinder

This document specifies a method for the evaluation of the buckling load which: a) takes into account a geometric model of the hydraulic cylinder, meaning it does not treat the hydraulic cylinder as an equivalent column, b) can be used for all types of cylinder mounting and rod end connection specified in Table 2, c) includes a factor of safety, k, to be set by the person performing the calculations and reported with the results of the calculations, d) takes into account possible off-axis loading, e) takes into account the weight of the hydraulic cylinder, meaning it does not neglect all transverse loads applied on the hydraulic cylinder, f) can be implemented as a simple computer program, and g) considers the cylinder fully extended. The method specified is based on the elastic buckling theory and is applicable to single and double acting cylinders that conform to ISO 6020 (all parts), ISO 6022 and ISO 10762. If necessary, finite element analyses can be used to verify as well as to determine the buckling load. The method is not developed for thin-walled cylinders, double-rods or plunger cylinders. The method is not developed for internal (rod) buckling. The friction of spherical bearings is not taken into account. NOTE This method is based mainly on original work by Fred Hoblit[2]. This method has been established in reference to the standard NFPA/T3.6.37[1].

  • Technical specification
    20 pages
    English language
    sale 15% off
  • Technical specification
    20 pages
    French language
    sale 15% off
ISO
ISO 10100:2020(Main)
Hydraulic fluid power — Cylinders — Acceptance tests
SIST ISO 10100:2021

This document specifies acceptance and function tests for hydraulic fluid power cylinders.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
ISO
ISO 6099:2018(Main)
Fluid power systems and components — Cylinders — Identification code for mounting dimensions and mounting types

This document establishes a convention for the identification of mounting dimensions and types used in the mounting of fluid power cylinders. It specifies a code for identifying cylinder mounting, envelope, accessory and connector dimensions, and for cylinder mounting and accessory types. This document does not represent a standard list of all fluid power cylinder mounting and accessory types.

  • Standard
    68 pages
    English language
    sale 15% off
  • Standard
    68 pages
    French language
    sale 15% off
ISO
ISO 8140:2018(Main)
Pneumatic fluid power — Cylinders, 1 000 kPa (10 bar) series — Mounting dimensions of rod-end clevises

This document specifies the mounting dimensions required for interchangeability of rod-end clevises of pneumatic cylinders. The rod-end clevises have been designed specifically for use with 1 000 kPa [10 bar1] series cylinders manufactured in accordance with ISO 6432 and ISO 15552, but this does not limit their application. The clevises are used on piston rods of pneumatic cylinders for mechanically transmitting the cylinder force. The design of the clevises is based on the maximum forces resulting from the specified internal diameter of the cylinders and pressure according to ISO 6432, ISO 15552 and ISO 21287. 1 1 bar = 100 kPa = 105 Pa; 1 Pa = 1 N/m2.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 8139:2018(Main)
Pneumatic fluid power — Cylinders, 1 000 kPa (10 bar) series — Mounting dimensions of rod-end spherical eyes

This document specifies the mounting dimensions required for interchangeability of rod-end spherical eyes of pneumatic cylinders. The rod-end spherical eyes have been designed specifically for use with 1 000 kPa [10 bar[1]] series cylinders manufactured in accordance with ISO 6432 and ISO 15552, but this does not limit their application. The spherical bearing end eyes are used on piston rods of pneumatic cylinders for mechanically transmitting the cylinder force under oscillatory rotational and tilting movements. The design of the rod-end spherical eyes is based on the maximum forces resulting from the specified internal diameter of the cylinders and pressure according to ISO 6432, ISO 15552 and ISO 21287. [1] 1 bar = 100 kPa = 105 Pa; 1 Pa = 1 N/m2.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 15552:2018(Main)
Pneumatic fluid power — Cylinders with detachable mountings, 1 000 kPa (10 bar) series, bores from 32 mm to 320 mm — Basic, mounting and accessories dimensions
SIST ISO 15552:2021

ISO 15552:2018 establishes a metric series of basic, mounting and accessories dimensions as required for interchangeability of single or double rod pneumatic cylinders with or without provision for magnetic sensors for a maximum rated pressure of 1 000 kPa (10 bar). ISO 15552:2018 applies to pneumatic cylinders with detachable mountings.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    20 pages
    French language
    sale 15% off
ISO
ISO 16656:2016(Main)
Hydraulic fluid power — Single rod, short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar) — Mounting dimensions
SIST ISO 16656:2021

ISO 16656:2016 establishes mounting dimensions for single rod short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar) with or without magnetic functions, as required for interchangeability of these commonly used hydraulic cylinders.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
ISO
ISO 4393:2015(Main)
Fluid power systems and components — Cylinders — Basic series of piston strokes
SIST ISO 4393:2016

ISO 4393:2015 specifies the preferred series of piston strokes for application to single-acting and double-acting fluid power cylinders. These strokes are mainly used for pneumatic cylinders but may also be used for hydraulic cylinders.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    3 pages
    French language
    sale 15% off