Textiles - Test methods for nonwovens - Part 8: Determination of liquid strike-through time (simulated urine)

Provides a method for measuring the time of liquid (simulated urine) strike-through for nonwovens. Does not simulate in-use conditions for finished products.

Textiles — Méthodes d'essai pour nontissés — Partie 8: Détermination du temps de transpercement des liquides (urine artificielle)

General Information

Status
Published
Publication Date
26-Dec-1995
Technical Committee
ISO/TC 38 - Textiles
Drafting Committee
ISO/TC 38 - Textiles
Current Stage
9599 - Withdrawal of International Standard
Start Date
06-Oct-2025
Completion Date
13-Dec-2025

Relations

Effective Date
13-Jan-2024

Overview - ISO 9073-8:1995 (Textiles - Nonwovens - Liquid strike-through time)

ISO 9073-8:1995 specifies a laboratory method for measuring the liquid strike-through time of nonwoven coverstocks using simulated urine. The procedure times how long a defined volume of simulated urine takes to pass through a nonwoven sample into a reference absorbent pad. The method is intended for comparative testing of nonwoven materials and does not simulate in-use conditions for finished products (e.g., diapers or pads).

Key topics and technical requirements

  • Test principle: A measured volume (5.0 ml) of simulated urine is discharged onto a nonwoven test piece; electronic timing starts when liquid bridges electrodes and stops when penetration is complete.
  • Simulated urine: 9 g/l sodium chloride solution in Grade 3 water (ISO 3696) with a surface tension of 70 ± 2 mN/m. Surface tension must be checked before each series; any surfactant addition must be reported.
  • Reference absorbent pad: Five layers of filter paper (100 mm × 100 mm) with a specified strike-through benchmark (mean ~3 ± 0.5 s in 10 determinations).
  • Apparatus: 50 ml burette, funnel with magnetic valve (discharge characteristics specified), strike-through plate with corrosion‑resistant electrodes (1.6 mm platinum or stainless wire), transparent baseplate (~125 × 125 × 5 mm), and an electronic timer readable to 0.01 s.
  • Samples & conditioning: Cut 10 test pieces (125 mm × 125 mm recommended) and condition them per ISO 139 standard atmospheres.
  • Results reporting: Individual strike-through times, mean time, coefficient of variation, conditioning atmosphere, any deviations (e.g., surfactant use).

Practical applications and users

ISO 9073-8 is used to:

  • Compare liquid penetration performance of nonwoven coverstocks in product development and material selection.
  • Support quality control and batch-to-batch consistency checks for nonwoven manufacturers.
  • Provide standardized data for R&D teams optimizing liquid-handling surfaces in hygiene products (e.g., diaper topsheets, medical pads).
  • Supply test laboratories with a reproducible method for reporting strike-through times.

Primary users:

  • Nonwoven fabric manufacturers
  • Personal hygiene and medical absorbent product developers
  • Accredited testing laboratories and quality assurance teams
  • Procurement and specification engineers assessing coverstock performance

Related standards

  • ISO 9073 (series) - Test methods for nonwovens (other parts: mass, thickness, tensile, tear, drape, etc.)
  • ISO 139 - Standard atmospheres for conditioning and testing
  • ISO 186 - Sampling to determine average quality
  • ISO 3696 - Water for analytical laboratory use

Keywords: ISO 9073-8, nonwovens test methods, liquid strike-through time, simulated urine, nonwoven coverstock, absorbent pad testing, textile testing, hygiene product development.

Standard

ISO 9073-8:1995 - Textiles — Test methods for nonwovens — Part 8: Determination of liquid strike-through time (simulated urine) Released:12/27/1995

English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard

ISO 9073-8:1995 - Textiles — Méthodes d'essai pour nontissés — Partie 8: Détermination du temps de transpercement des liquides (urine artificielle) Released:12/27/1995

French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Frequently Asked Questions

ISO 9073-8:1995 is a standard published by the International Organization for Standardization (ISO). Its full title is "Textiles - Test methods for nonwovens - Part 8: Determination of liquid strike-through time (simulated urine)". This standard covers: Provides a method for measuring the time of liquid (simulated urine) strike-through for nonwovens. Does not simulate in-use conditions for finished products.

Provides a method for measuring the time of liquid (simulated urine) strike-through for nonwovens. Does not simulate in-use conditions for finished products.

ISO 9073-8:1995 is classified under the following ICS (International Classification for Standards) categories: 59.080.30 - Textile fabrics. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 9073-8:1995 has the following relationships with other standards: It is inter standard links to ISO 9073-8:2025. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

You can purchase ISO 9073-8:1995 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.

Standards Content (Sample)


IS0
INTERNATIONAL
9073-8
STANDARD
First edition
1995-l 2-l 5
Test methods for
Textiles -
nonwovens -
Part 8:
Determination of liquid strike-through time
(simulated urine)
M&hodes d’essai pour nontissbs -
Textiles -
Partie 8: DGtermination du temps de transpercement des liquides
(urine artificielle)
Reference number
IS0 9073-8: 1995(E)
IS0 9073-8: 1995(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 9073-8 was prepared by Technical Committee
lSO/TC 38, Textiles.
IS0 9073 consists of the following parts, under the general title Textiles
- Test methods for nonwovens:
- Part 1: Determination of mass per unit area
- Part 2: Determination of thickness
- Part 3: Determination of tensile strength and elongation
- Part 4: Determination of tear resistance
- Part 7: Determination of bending length
- Part 8: Determination of liquid strike-through time (simulated urine)
- Part 9: Determination of drape coefficient
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopyrng and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
INTERNATIONAL STANDARD 0 ISO IS0 9073-8: 1995(E)
Textiles - Test methods for nonwovens -
Part 8:
Determination of liquid strike-through time
(simulated urine)
1 Scope 3 Definition
This part of IS0 9073 specifies a method for measur- For the purposes of this part of IS0 9073, the follow-
ing the time of liquid (simulated urine) strike-through ing definition applies.
for nonwoven coverstocks. The method is suitable for
making comparisons between different nonwoven 3.1 strike-through time: Time taken for a known
coverstocks. It does not simulate in-use conditions for
volume of liquid, applied to the surface of a piece of
finished products.
nonwoven coverstock with an absorbent pad under-
neath, to pass through the nonwoven coverstock.
NOTE 1 This International Standard describes a test
method specific to nonwovens. Other International Stan-
dards applicable to textile, paper, plastics, rubber or other
4 Principle
materials can also be applied to test certain nonwoven
characteristics.
A specified quantity of simulated urine is discharged
at a specified rate under specified conditions onto a
test piece of nonwoven which is placed on a refer-
2 Normative references
ence absorbent pad. The time taken for all the liquid
to penetrate the nonwoven is measured electron-
The following standards contain provisions which,
ically.
through reference in this text, constitute provisions
of this part of IS0 9073. At the time of publication, the
editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this
5 Material and reagents
part of IS0 9073 are encouraged to investigate the
possibility of applying the most recent editions of the
5.1 Reference absorbent pad, consisting of five
standards indicated below. Members of IEC and IS0
layers of reference filter paper (100 mm x 100 mm)
maintain registers of currently valid International
with the smooth sides uppermost, and having a mean
Standards.
strike-through time in 10 determinations without the
nonwoven of (3 + 0,5) s.
IS0 139: 1973, Textiles - Standard atmospheres for
conditioning and testing.
NOTE 2 Information concerning suitable filter paper may
be obtained from:
IS0 186: 1994, Paper and board - Sampling to deter-
mine average quality.
INDA, 1001 Winstead Drive, Suite 460, Cat-y, NC 27513,
USA;
I SO 3696: 1987, Water for analytical laboratory use -
Specification and test methods. EDANA, 157 av. Eugene Plasky, B-1040 Brussels.

0 IS0
IS0 9073=8:1995(E)
5.2 Simulated urine, consisting of a 9 g/l solution
7 Sampling
of sodium chloride in grade 3 water conforming to
IS0 3696, with a surface tension of (70 + 2) mN/m.
Carry out sampling in acc
...


NORME
Iso
INTERNATIONALE
9073-8
Première édition
1995-l 2-15
Textiles - Méthodes d’essai pour
nontissés -
Partie 8:
Détermination du temps de transpercement
des liquides (urine artificielle)
Textiles - Test methods for nonwovens -
Part 8: Determination of liquid strike-through time (simulated urine)
Numéro de référence
ISO 9073-8: 1995(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération
mondiale d’organismes nationaux de normalisation (comités membres de
I’ISO). L’élaboration des Normes internationales est en général confiée aux
comités techniques de I’ISO. Chaque comité membre intéressé par une
étude a le droit de faire partie du comité technique créé à cet effet. Les
organisations internationales, gouvernementales et non gouvernemen-
tales, en liaison avec I’ISO participent également aux travaux. L’ISO colla-
bore étroitement avec la Commission électrotechnique internationale (CEI)
en ce qui concerne la normalisation électrotechnique.
Les projets de Normes internationales adoptés par les comités techniques
sont soumis aux comités membres pour vote. Leur publication comme
Normes internationales requiert l’approbation de 75 % au moins des co-
mités membres votants.
La Norme internationale ISO 9073-8 a été élaborée par le comité techni-
que lSO/TC 38, Textiles.
L’ISO 9073 comprend les parties suivantes, présentées sous le titre gé-
néral Textiles - Méthodes d’essai pour nontissés:
- Partie 1: Détermination de la masse surfacique
- Partie 2: Détermination de l’épaisseur
- Partie 3: Détermination la traction
/a résis tance à et de
l’allongement
- Partie 4: Détermination de la résistance à la déchirure
- Partie 7: Détermination de la longueur de flexion
- Partie 8: Détermination du temps de transpercemen t des liquides
(urine artificielle)
- Partie 9: Détermination du coefficient de drapé
0 ISO 1995
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publi-
cation ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun pro-
cédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord
écrit de l’éditeur.
Organisation internationale de normalisation
Case Postale 56 l CH-I 211 Genève 20 l Suisse
Imprimé en Suisse
ii
NORME INTERNATIONALE 0 ISO ISO 9073-8: 1995(F)
- Méthodes d’essai pour nontissés -
Textiles
Partie 8:
Détermination du temps de transpercement des liquides
(urine artificielle)
ISO 3696:1987, Eau pour laboratoire à usage analyti-
1 Domaine d’application
- Spécifica tion et méthodes d’essai.
que
La présente partie de I’ISO 9073 prescrit une mé-
thode pour la détermination du temps de transper-
3 Définition
cernent des liquides (urine artificielle) dans les
enveloppes en nontissé pour couches. La méthode
Pour les besoins de la présente partie de I’ISO 9073,
permet d’établir des comparaisons entre différentes
la définition suivante s’applique.
enveloppes nontissées. Elle ne permet pas de simuler
les conditions d’utilisation des produits finis.
3.1 temps de transpercement: Temps que met un
volume connu de liquide, lorsqu’il est appliqué à la
La présente Norme internationale décrit une
NOTE 1
surface d’une éprouvette d’enveloppe nontissée pour
méthode d’essai spécifique aux nontissés. D’autres Normes
couche placée sur un coussin absorbant, pour
internationales applicables aux textile, papier, plastique, ca-
s’écouler au travers de l’enveloppe nontissée.
outchouc ou autres matériaux peuvent également être utili-
sées pour déterminer certaines caractéristiques des
nontissés.
4 Principe
2 Références normatives
Une quantité prescrite d’urine artificelle est déversée
à un débit spécifié dans des conditions définies sur
Les normes suivantes contiennent des dispositions
une éprouvette d’étoffe nontissée qui est placée sur
qui, par suite de la référence qui en est faite, consti-
un coussin absorbant de référence. Le temps que met
tuent des dispositions valables pour la présente partie
le liquide pour transpercer le nontissé est mesuré par
de I’ISO 9073. Au moment de la publication, les édi-
des moyens électroniques.
tions indiquées étaient en vigueur. Toute norme est
sujette à révision et les parties prenantes des accords
5 Matériaux et réactifs
fondés sur la présente partie de I’ISO 9073 sont invi-
tées à rechercher la possibilité d’appliquer les éditions
les plus récentes des normes indiquées ci-après. Les
5.1 Coussin absorbant de référence, composé de
membres de la CEI et de I’ISO possèdent le registre
filtre de référence
cinq couches de papier
des Normes internationales en vigueur à un moment
(100 mm x 100 mm), les surfaces lisses étant au-
donné.
dessus, et dont le temps moyen de transpercement
établi, en l’absence du nontissé, par 10 détermi-
ISO ‘l39: 1973, Textiles - Atmosphères normales de
nations est de (3 + 0,5) s.
conditionnement et d’essai.
NOTE 2 II est possible d’obtenir des informations
ISO 186: 1994, Papier et carton - Échantillonnage
concernant un papier filtre approprie auprès des asso-
pour déterminer la qualité moyenne. ciations suivantes de l’industrie des nontissés:

0 ISO
ISO 9073-8: 1995(F)
sateurs de la présente méthode de faire valider leur équi-
INDA, 1001 Winstead Drive, Suite 460, Cary, NC 27513,
pement par rapport aux rés ultats fournis par le producteur
USA;
du papier filtre utilis é.
EDANA, 157 av. Eugène Plasky, B-l 040 Bruxelles.
7 Échantillonnage
5.2 Urine artificielle, composée d’une solution de
9 g de chlorure de sodium par litre d’eau de qu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...