ISO/IEC 22460-2:2024

International
Standard
ISO/IEC 22460-2
First edition
Cards and security devices for
personal identification — ISO UAS
license and drone/UAS security
module —
Part 2:
Drone/UAS security module
Cartes et dispositifs de sécurité pour l'identification des
personnes — Permis ISO de systèmes d'aéronefs sans équipage
à bord et module de sécurité de drone/système d'aéronefs sans
équipage à bord —
Partie 2: Module de sécurité de drone/système d'aéronefs sans
équipage à bord
PROOF/ÉPREUVE
Reference number
ISO/IEC 22460-2:2024(en) © ISO/IEC 2024

---------------------- Page: 1 ----------------------
ISO/IEC 22460-2:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO/IEC 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/IEC 22460-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms. 2
5 Overview of a drone security module . 3
5.1 General .3
5.2 Form-factor of a drone security module .3
5.3 Use of a drone security module .3
6 Data format of a drone security module . 4
6.1 General .4
6.2 Drone pilot/operator license .4
6.3 Personal identification data for a drone .4
6.4 Cryptographic key-related data .4
6.5 Other data .5
7 Cryptographic functions of a drone security module .
...

2024-01-12
ISO/IEC PRF 22460-2:2024(E)
ISO/IEC JTC 1/SC 17/WG 12
Secretariat: KATS BSI
Date: 2024-03-06
Cards and security devices for personal identification — — ISO
UAS license and drone/UAS security module —
—
Part 2:
Drone/UAS security module
Cartes et dispositifs de sécurité pour l'identification pour personnelle — Licence ISO UAS des personnes —
Permis ISO de systèmes d'aéronefs sans équipage à bord et module de sécurité drone/UAS —
de drone/système d'aéronefs sans équipage à bord —
Partie 2: Module de sécurité de drone/UASsystème d'aéronefs sans équipage à bord

---------------------- Page: 1 ----------------------
ISO #####-#:####(X)
Copyright notice
This ISO document is a
working draftFDIS stage
2 © ISO #### – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC PRF 22460-2:2024(en)
© ISO/IEC 2024
All rights reserved. Unless otherwise specified, or committee draft and is copyright-protected by ISO. While required
in the reproductioncontext of working drafts or committee drafts in any form for use by participants in the ISO
standards development process is permitted without prior permission from ISO, neither its implementation, no part
of this document nor any extract from itpublication may be reproduced, stored or utilized otherwise in any form or
transmitted in any form for any other purposeby any means, electronic or mechanical, including photocopying, or
posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO.
Requests for permission to reproduce this document for at the purpose of selling it should be addressed as shownaddress
below or to ISO'sISO’s member body in the country of the requester:.
[Indicate the full address, telephone number, fax number, telex number,  mail address, as appropriate, of the Copyright
Manager of the ISO member body responsible for the secretariat of the TC or SC within the framework of which the
working document has been prepared.]
Reproduction for sales purposes may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO/IEC 2024 – All rights reserved

iii

---------------------- Page: 3 ----------------------
ISO/IEC PRF 22460-2:2024(en)


© ISO/IEC 2024 – All rights reserved

iv

---------------------- Page: 4 ----------------------
ISO/IEC PRF 22460-2:2024(en)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members
of ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC
Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives or
www.iec.ch/members_experts/refdocs).
Field Code Changed
ISO and IEC draw attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO and IEC take no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO and IEC had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent database
available at www.iso.org/patents and https://patents.iec.ch.www.iso.org/patents and https://patents.iec.ch.
ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www.iso.org/iso/foreword.html.www.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-
Field Code Changed
standards.
This document was pr
...