ISO 5429:2012
(Main)Coated abrasives - Flap wheels with incorporated flanges or separate flanges
Coated abrasives - Flap wheels with incorporated flanges or separate flanges
This International Standard specifies the nominal dimensions and limit deviations of flap wheels with incorporated flanges or separate flanges for use on stationary grinding machines.
Abrasifs appliqués — Roues à lamelles à flasques incorporés ou amovibles
La présente Norme internationale spécifie les dimensions nominales et les écarts limites des roues à lamelles à flasques incorporés ou amovibles destinées aux meuleuses fixes.
General Information
- Status
- Published
- Publication Date
- 12-Apr-2012
- Technical Committee
- ISO/TC 29/SC 5 - Grinding wheels and abrasives
- Drafting Committee
- ISO/TC 29/SC 5 - Grinding wheels and abrasives
- Current Stage
- 9093 - International Standard confirmed
- Start Date
- 10-Feb-2022
- Completion Date
- 13-Dec-2025
Relations
- Effective Date
- 18-Feb-2010
Overview
ISO 5429:2012 specifies nominal dimensions and limit deviations for coated-abrasive flap wheels with incorporated flanges (version A) or separate flanges (version B) intended for use on stationary grinding machines. This third edition updates the 2005 version by adding additional flap-wheel widths and aligning the dimensional table editorially with ISO 3919. The standard defines how to designate and mark these flap wheels for consistent identification and safe operation.
Key Topics
- Scope and use: Applies to flap wheels fitted with incorporated or separate flanges for stationary grinding machines.
- Dimensions and tolerances:
- Diameter (D) and width (T) combinations are listed in a dimensional table (Table 1).
- Diameter tolerance shown in the document header is D ±1 mm (as specified in the table).
- Bore diameter (H) for version A is indicated but H dimensions are left to the manufacturer’s discretion.
- Designation format:
- Required designation elements: product name, reference to ISO 5429, flange version (A or B), diameter D (mm), width T (mm), and bore H (mm for version A).
- Example: Flap wheel ISO 5429 - A 350 × 75 × 40
- Marking requirements:
- Manufacturer, supplier or trademark
- Dimensions
- Maximum operating speed
- Maximum permissible speed of rotation
- Grit size
- Informative illustrations: A flange sketch is included for information only and does not mandate flange shape or attachment method.
Applications
ISO 5429 is directly relevant to manufacturers, suppliers, quality engineers, procurement professionals, and end-users of coated-abrasive flap wheels who need standardized products for:
- Surface finishing, deburring, blending and edge work on stationary grinding machines
- Ensuring interchangeability and safety through consistent dimensions and marking
- Compliance checks during incoming inspection and quality control
Typical users:
- Flap wheel manufacturers and tool designers
- Industrial buyers and maintenance teams in metalworking, fabrication, and manufacturing shops
- Standards and compliance officers managing abrasive product specifications
Related Standards
- ISO 3919 - Coated abrasives - Flap wheels with shaft (referenced in ISO 5429 for editorial alignment and related dimensional practice)
Keywords: ISO 5429, flap wheels, coated abrasives, incorporated flanges, separate flanges, dimensions, marking, stationary grinding machines, grit size, nominal dimensions.
ISO 5429:2012 - Coated abrasives -- Flap wheels with incorporated flanges or separate flanges
ISO 5429:2012 - Abrasifs appliqués -- Roues a lamelles a flasques incorporés ou amovibles
Frequently Asked Questions
ISO 5429:2012 is a standard published by the International Organization for Standardization (ISO). Its full title is "Coated abrasives - Flap wheels with incorporated flanges or separate flanges". This standard covers: This International Standard specifies the nominal dimensions and limit deviations of flap wheels with incorporated flanges or separate flanges for use on stationary grinding machines.
This International Standard specifies the nominal dimensions and limit deviations of flap wheels with incorporated flanges or separate flanges for use on stationary grinding machines.
ISO 5429:2012 is classified under the following ICS (International Classification for Standards) categories: 25.100.70 - Abrasives. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 5429:2012 has the following relationships with other standards: It is inter standard links to ISO 5429:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase ISO 5429:2012 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 5429
Third edition
2012-04-15
Coated abrasives — Flap wheels with
incorporated flanges or separate flanges
Abrasifs appliqués — Roues à lamelles à flasques incorporés ou amovibles
Reference number
©
ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5429 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels
and abrasives.
This third edition cancels and replaces the second edition (ISO 5429:2005), which has been technically revised.
Significant changes from ISO 5429:2005 are as follows:
a) further dimensions have been included, i.e. in Table
...
NORME ISO
INTERNATIONALE 5429
Troisième édition
2012-04-15
Abrasifs appliqués — Roues à lamelles à
flasques incorporés ou amovibles
Coated abrasives — Flap wheels with incorporated flanges or
separate flanges
Numéro de référence
©
ISO 2012
DOCUMENT PROTÉGÉ PAR COPYRIGHT
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord écrit
de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2012 – Tous droits réservés
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux de
normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général confiée aux
comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales,
en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur publication
comme Normes internationales requiert l’approbation de 75 % au moins des comités membres votants.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de droits
de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de ne pas avoir
identifié de tels droits de propriété et averti de leur existence.
L’ISO 5429 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 5, Meules et abrasifs.
Cette troisième édition annule et remplace la deuxième édition (ISO 5429:2005), qui a fait l’objet d’une
révision technique.
Les principaux changements par rapport à l’ISO 5429:2005 sont les suivants:
a) ajout de dimensions supplémentaires, c’est-à-dire ajout de largeurs
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...