ISO 603-9:2024
(Main)Bonded abrasive products - Dimensions - Part 9: Grinding wheels for high-pressure grinding
Bonded abrasive products - Dimensions - Part 9: Grinding wheels for high-pressure grinding
This document specifies the nominal dimensions, in millimetres, of: - shape type 1: straight grinding wheel. These bonded abrasive products are intended to be used for deburring and fettling of any surface of a workpiece. The workpiece and the grinding wheel are mechanically guided. This document does not specify limit deviations and run-out tolerances, which are given in ISO 13942.
Produits abrasifs agglomérés — Dimensions — Partie 9: Meules pour meulage haute pression
Le présent document spécifie les dimensions nominales, en millimètres, de: — forme de type 1: meule plate. Ces produits abrasifs agglomérés sont destinés à être utilisés pour l'ébarbage et l'ébavurage de surfaces quelconques d'une pièce. La pièce et la meule sont guidées mécaniquement. Le présent document ne spécifie pas les écarts limites et les tolérances de battement, qui sont donnés dans l'ISO 13942.
General Information
- Status
- Published
- Publication Date
- 30-Jan-2024
- Technical Committee
- ISO/TC 29/SC 5 - Grinding wheels and abrasives
- Drafting Committee
- ISO/TC 29/SC 5 - Grinding wheels and abrasives
- Current Stage
- 6060 - International Standard published
- Start Date
- 31-Jan-2024
- Due Date
- 08-Apr-2024
- Completion Date
- 31-Jan-2024
Relations
- Effective Date
- 06-Jun-2022
- Effective Date
- 06-Jun-2022
Overview
ISO 603-9:2024 - Bonded abrasive products - Dimensions - Part 9: Grinding wheels for high-pressure grinding specifies the nominal dimensions (mm) for shape type 1: straight grinding wheels used in high‑pressure grinding operations. The standard covers the common overall diameters, thicknesses and bore sizes for straight wheels intended for deburring and fettling of workpiece surfaces where the workpiece and grinding wheel are mechanically guided on stationary (fixed) machines. ISO 603-9:2024 updates and replaces the 1999 edition and aligns dimensional options with current practice, including commonly used imperial equivalents.
Key topics and requirements
- Scope: Defines nominal dimensions only - it does not set limit deviations or run‑out tolerances (those are provided in ISO 13942).
- Shape and symbols: Refers to ISO 525 for the shape type definitions and the dimensional symbols used to describe a type 1 straight wheel.
- Dimension tables: Includes a table of the most common outside diameters, overall thicknesses and bore diameters (with typical values shown in brackets and commonly used imperial sizes noted).
- Designation: Wheel identification and designation are to be carried out in accordance with ISO 525.
- Normative references and bibliography: Points to related ISO documents (e.g., ISO 525, ISO 13942) and industry references for unbalance testing and grain size designation.
Applications and users
Who uses ISO 603-9:2024:
- Grinding wheel manufacturers - to standardize product dimensions for high‑pressure straight wheels.
- Machine builders and OEMs - to specify compatible wheel dimensions for stationary high‑pressure grinding machines.
- Purchasing and inventory managers - to order and stock wheels with standardized dimensions and imperial equivalents.
- Quality and safety engineers - to ensure dimensional compatibility before referring to tolerances and run‑out limits in ISO 13942.
- Maintenance and toolroom personnel - for selecting replacement wheels that fit existing spindles and bores.
Practical use cases:
- Specifying replacement wheels for deburring and fettling operations.
- Ensuring interchangeability across suppliers and international trade.
- Defining product families and SKU dimensions in catalogs.
Related standards
- ISO 525 - Bonded abrasive products: shape types, designation and marking (dimension/shape definitions and designation rules)
- ISO 13942 - Limit deviations and run‑out tolerances for bonded abrasive products
- ISO 6103 - Permissible unbalances of grinding wheels
- ISO 8486 (all parts) - Grain size distribution designation
For full dimensional tables, symbols and formal designation rules consult the official ISO 603-9:2024 publication available from ISO or your national standards body.
ISO 603-9:2024 - Bonded abrasive products — Dimensions — Part 9: Grinding wheels for high-pressure grinding Released:31. 01. 2024
ISO 603-9:2024 - Produits abrasifs agglomérés — Dimensions — Partie 9: Meules pour meulage haute pression Released:31. 01. 2024
Frequently Asked Questions
ISO 603-9:2024 is a standard published by the International Organization for Standardization (ISO). Its full title is "Bonded abrasive products - Dimensions - Part 9: Grinding wheels for high-pressure grinding". This standard covers: This document specifies the nominal dimensions, in millimetres, of: - shape type 1: straight grinding wheel. These bonded abrasive products are intended to be used for deburring and fettling of any surface of a workpiece. The workpiece and the grinding wheel are mechanically guided. This document does not specify limit deviations and run-out tolerances, which are given in ISO 13942.
This document specifies the nominal dimensions, in millimetres, of: - shape type 1: straight grinding wheel. These bonded abrasive products are intended to be used for deburring and fettling of any surface of a workpiece. The workpiece and the grinding wheel are mechanically guided. This document does not specify limit deviations and run-out tolerances, which are given in ISO 13942.
ISO 603-9:2024 is classified under the following ICS (International Classification for Standards) categories: 25.100.70 - Abrasives. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 603-9:2024 has the following relationships with other standards: It is inter standard links to ISO 603-9:1999/Cor 1:1999, ISO 603-9:1999. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase ISO 603-9:2024 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
International
Standard
ISO 603-9
Second edition
Bonded abrasive products —
2024-01
Dimensions —
Part 9:
Grinding wheels for high-pressure
grinding
Produits abrasifs agglomérés — Dimensions —
Partie 9: Meules pour meulage haute pression
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Shape type and dimensions. 1
5 Designation . 2
Bibliography . 3
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent ri
...
Norme
internationale
ISO 603-9
Deuxième édition
Produits abrasifs agglomérés —
2024-01
Dimensions —
Partie 9:
Meules pour meulage haute
pression
Bonded abrasive products — Dimensions —
Part 9: Grinding wheels for high-pressure grinding
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2024
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Type de forme et dimensions . 1
5 Désignation . 2
Bibliographie . 3
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n'avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de propriété.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et n
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...