iTeh Standards logo
EURUSD
Your shopping cart is empty.
ISO

ISO 3601-1:2012/Cor 1:2012

(Corrigendum)

Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes — Technical Corrigendum 1

Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes — Technical Corrigendum 1

Transmissions hydrauliques et pneumatiques — Joints toriques — Partie 1: Diamètres intérieurs, sections, tolérances et codes d'identification dimensionnelle — Rectificatif technique 1

General Information

Status
Published
Publication Date
12-Jul-2012
ICS
23.100.60 - Filters, seals and contamination of fluids
83.140.50 - Seals
Technical Committee
ISO/TC 131/SC 7 - Sealing devices
Drafting Committee
ISO/TC 131/SC 7/WG 3 - Design criteria for standard O-ring applications
Current Stage
6060 - International Standard published
Start Date
13-Jul-2012
Due Date
26-Jun-2015
Completion Date
26-Jun-2015
Ref Project

Relations

Corrects
ISO 3601-1:2012 - Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes
Effective Date
07-Aug-2021
ISO 3601-1:2012/Cor 1:2012ISO 3601-1:2012/Cor 1:2012
PreviousNext
Standard
ISO 3601-1:2012/Cor 1:2012
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL STANDARD ISO 3601-1:2012
TECHNICAL CORRIGENDUM 1
Published 2012-07-15
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION  МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ  ORGANISATION INTERNATIONALE DE NORMALISATION

Fluid power systems — O-rings —
Part 1:
Inside diameters, cross-sections, tolerances and designation
codes
TECHNICAL CORRIGENDUM 1
Transmissions hydrauliques et pneumatiques — Joints toriques —
Partie 1: Diamètres intérieurs, sections, tolérances et codes d'identification dimensionnelle
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

This May Also Interest You

ISO
ISO 3601-2:2025(Main)
Fluid power systems — O-rings — Part 2: Housing dimensions for general applications

This document specifies the housing dimensions for class A O-rings for general industrial applications conforming to ISO 3601-1, as well as housing dimensions for class B O-rings used on selected metric-dimensioned hardware, e.g. fluid power cylinder bores and piston rods. These O-rings are for use in general hydraulic and pneumatic applications without and with anti-extrusion rings (back-up rings). The dimensions of the O-rings (d1 and d2), size codes (SC) and tolerances conform to ISO 3601-1. This document also addresses different design approaches in industry, and this is reflected in the table structures for hardware dimensions. Using the O-ring as a starting point to design the optimal hardware dimensions is reflected in REF Table_tab_3 \r \h Tables 3 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C0000005400610062006C0065005F007400610062005F0033000000 , REF Table_tab_5 \r \h 5 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C0000005400610062006C0065005F007400610062005F0035000000 , and REF Table_tab_8 \r \h 8 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C0000005400610062006C0065005F007400610062005F0038000000 . Using fixed hardware dimensions (i.e. bore/rod) and choosing the most appropriate O-ring to fit is reflected in REF Table_tab_4 \r \h Tables 4 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C0000005400610062006C0065005F007400610062005F0034000000 and REF Table_tab_6 \r \h 6 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C0000005400610062006C0065005F007400610062005F0036000000 . Housing dimensions for the O-rings intended for aerospace applications that are specified in ISO 3601-1 are addressed in REF Annex_sec_A \r \h Annex A 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000C00000041006E006E00650078005F007300650063005F0041000000 . NOTE 1 It is expected that O-ring housing dimensions for special applications be agreed upon between the O-ring manufacturer and the user. NOTE 2 The term “housing”, in this document, is used to describe the groove or cavity, into which the O-ring is fitted, and the mating surface, which between them confine the O-ring.

  • Standard
    55 pages
    English language
    sale 15% off
ISO
ISO 5119:2023(Main)
Low temperature sealing capability of elastomeric seals — Test methods

This specification details a test method for static O-ring seals in elastomeric materials which are subject to pressurized gas media at low temperatures. It gives guidance on the design of test equipment, standard test parameters, and reporting criteria. It does not specify performance criteria that should be agreed upon between supplier and customer. The test procedure may be used to test seals of alternate size and design or using alternative media but such deviations shall be detailed separately on the report form and the results shall not be used to determine the minimum operating temperature of seals of any other configuration than that tested.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
ISO
ISO 3601-1:2012/Amd 1:2019(Amendment)
Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes — Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 3601-3:2005/Amd 1:2018(Amendment)
Fluid power systems — O-rings — Part 3: Quality acceptance criteria — Amendment 1
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 16589-1:2011/Amd 1:2018(Amendment)
Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 1: Nominal dimensions and tolerances — Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
ISO
ISO 3601-2:2016(Main)
Fluid power systems — O-rings — Part 2: Housing dimensions for general applications

ISO 3601-2:2016 specifies the housing (gland) dimensions for class A O-rings for general industrial applications conforming to ISO 3601-1, as well as housing dimensions for class B O-rings used on selected metric-dimensioned hardware, e.g. fluid power cylinder bores and piston rods. These O-rings are for use in general hydraulic and pneumatic applications without and with anti-extrusion rings (back-up rings). The dimensions of the O-rings (d1 and d2), size codes (SC) and tolerances conform to ISO 3601-1. Housing dimensions for the O-rings intended for aerospace applications that are specified in ISO 3601-1 are addressed in Annex A.

  • Standard
    54 pages
    English language
    sale 15% off
  • Standard
    47 pages
    French language
    sale 15% off
ISO
ISO 3601-5:2015(Main)
Fluid power systems — O-rings — Part 5: Specification of elastomeric materials for industrial applications
SIST ISO 3601-5:2016

ISO 3601-5:2015 contains the material specification of a selection of standard elastomeric materials (rubber) for O-rings used in general industrial applications. It also indicates the ability of the materials to satisfy many of the requirements associated with fluid power components. Only materials which are in universal usage are specified; other compounds are available and can be used. The required physical properties and test methods (including test specimen) should be agreed upon between equipment manufacturer/user and O-ring manufacturer/supplier.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    13 pages
    English language
    sale 15% off
ISO
ISO 3601-1:2012(Main)
Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes

ISO 3601-1:2012 specifies the inside diameters, cross-sections, tolerances and designation codes for O-rings used in fluid power systems for general industrial and aerospace applications. The dimensions and tolerances specified in ISO 3601-1:2012 are suitable for any elastomeric material, provided that suitable tooling is available.

  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    36 pages
    French language
    sale 15% off
ISO
ISO 16589-2:2011(Main)
Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 2: Vocabulary
SIST ISO 16589-2:2014

ISO 16589-2:2011 establishes the vocabulary for seals utilizing sealing elements manufactured from suitably formulated compounds, based on thermoplastic materials, such as polytetrafluoroethylene (PTFE) that are considered suitable for use under low-pressure conditions.

  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    38 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
ISO
ISO 16589-1:2011(Main)
Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 1: Nominal dimensions and tolerances
SIST ISO 16589-1:2014

ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low-pressure conditions. ISO 16589-1:2011 shows seal types and examples. It also specifies the nominal dimensions and tolerance of the seals, shafts and housings, as well as a dimensional identification code.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    13 pages
    English language
    sale 15% off