ISO 13596:2000
(Main)Aerospace - Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated - Dimensions
Aerospace - Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated - Dimensions
This International Standard specifies the dimensions of closed inserts, with self-locking MJ threads, in metallic material, coated or uncoated, for honeycomb and composite materials. The classification referring to strength and temperature, depending on the core material and potting compound, is not specified. This International Standard is only applicable to the compilation of aerospace product standards.
Aéronautique et espace — Douilles filetées, à freinage interne et filetage MJ, du type fermé, en matériau métallique, revêtues ou non revêtues — Dimensions
La présente Norme internationale spécifie les dimensions des douilles filetées fermées, à freinage interne et filetage MJ, en matériau métallique, revêtues ou non revêtues, pour des matériaux composites et à nids d'abeilles. La classification concernant la résistance et la température, étant fonction du matériau de base et du mastic de remplissage, n'est pas spécifiée. La présente Norme internationale est applicable uniquement à l'élaboration de normes de produit destinées aux constructions aérospatiales.
General Information
- Status
- Published
- Publication Date
- 23-Feb-2000
- Technical Committee
- ISO/TC 20/SC 4 - Aerospace fastener systems
- Drafting Committee
- ISO/TC 20/SC 4 - Aerospace fastener systems
- Current Stage
- 9060 - Close of review
- Completion Date
- 04-Mar-2030
Overview
ISO 13596:2000 - "Aerospace - Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated - Dimensions" - defines the geometric requirements for closed, self‑locking metallic inserts with MJ threads intended for use in honeycomb and composite aerospace structures. The standard specifies configuration, dimensional tolerances (in millimetres) and features such as potting/vent holes and optional anti‑rotation provisions. It is intended solely for the compilation of aerospace product standards and does not assign strength or temperature classifications (these depend on core material and potting compound).
Key topics and requirements
- Scope and use: Applies to closed-type, self‑locking inserts with MJ threads in metallic material, coated or uncoated, installed in honeycomb and composite panels.
- Dimensions and tolerances: All dimensions and tolerances are given in millimetres and apply to inserts after any surface coating(s). Detailed geometry is provided in the standard’s figures and tables.
- Threading: Uses MJ thread codes (e.g., MJ3–MJ6) in accordance with MJ thread definitions; thread limit dimensions for mating bolts/nuts are referenced from ISO 5855-2.
- Functional features:
- Shank deformation area to provide the self‑locking action.
- Potting and vent hole(s) for installation in sandwich panels.
- Optional anti‑rotation feature on the shank or bottom flange (manufacturer’s option).
- Manufacturer discretion: Details of form not explicitly stated are left to the manufacturer, provided the dimensional requirements are met.
- Limitations: The standard does not specify strength or temperature classes - these depend on the combination of core material and potting compound and must be specified elsewhere.
Applications and users
- Typical applications:
- Fastening points in honeycomb and composite sandwich panels on aircraft and spacecraft.
- Attachment points for structural components, interiors, avionics equipment, and access panels where a flush/closed insert is required.
- Who uses this standard:
- Aerospace designers and structural engineers specifying inserts for composite/honeycomb assemblies.
- Fastener manufacturers and suppliers producing MJ-thread self‑locking inserts.
- Quality assurance, procurement, and certification teams ensuring dimensional conformity in aerospace product standards.
- Technical writers and standards committees compiling aerospace component specifications.
Related standards
- ISO 5855-2:1999 - Aerospace - MJ threads - Part 2: Limit dimensions for bolts and nuts (normative reference used by ISO 13596).
- Use ISO 13596 in conjunction with material, potting compound and strength/temperature specifications relevant to the specific aerospace application.
Keywords: ISO 13596:2000, aerospace inserts, MJ threads, self‑locking inserts, honeycomb inserts, composite inserts, dimensions, aerospace fastener standards, potting compound.
ISO 13596:2000 - Aerospace -- Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated -- Dimensions
ISO 13596:2000 - Aéronautique et espace -- Douilles filetées, a freinage interne et filetage MJ, du type fermé, en matériau métallique, revetues ou non revetues -- Dimensions
Frequently Asked Questions
ISO 13596:2000 is a standard published by the International Organization for Standardization (ISO). Its full title is "Aerospace - Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated - Dimensions". This standard covers: This International Standard specifies the dimensions of closed inserts, with self-locking MJ threads, in metallic material, coated or uncoated, for honeycomb and composite materials. The classification referring to strength and temperature, depending on the core material and potting compound, is not specified. This International Standard is only applicable to the compilation of aerospace product standards.
This International Standard specifies the dimensions of closed inserts, with self-locking MJ threads, in metallic material, coated or uncoated, for honeycomb and composite materials. The classification referring to strength and temperature, depending on the core material and potting compound, is not specified. This International Standard is only applicable to the compilation of aerospace product standards.
ISO 13596:2000 is classified under the following ICS (International Classification for Standards) categories: 49.030.99 - Other fasteners. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 13596:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13596
First edition
2000-03-01
Aerospace — Inserts, self-locking,
with MJ threads, closed type, in metallic
material, coated or uncoated — Dimensions
Aéronautique et espace — Douilles filetées, à freinage interne et filetage
MJ, du type fermé, en matériau métallique, revêtues ou non revêtues —
Dimensions
Reference number
©
ISO 2000
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or al
...
NORME ISO
INTERNATIONALE 13596
Première édition
2000-03-01
Aéronautique et espace — Douilles filetées,
à freinage interne et filetage MJ, du type
fermé, en matériau métallique, revêtues ou
non revêtues — Dimensions
Aerospace — Inserts, self-locking, with MJ threads, closed type, in metallic
material, coated or uncoated — Dimensions
Numéro de référence
©
ISO 2000
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
ImpriméenSuisse
ii © ISO 2000 – Tous droits réservés
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO, participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments de la présente Norme internationale peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et ave
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...