ISO 8873-1:2006
(Main)Rigid cellular plastics — Spray-applied polyurethane foam for thermal insulation — Part 1: Material specifications
Rigid cellular plastics — Spray-applied polyurethane foam for thermal insulation — Part 1: Material specifications
ISO 8873-1:2006 specifies minimum requirements and test methods for spray-applied polyurethane rigid cellular plastic, used as a thermal insulation for both building, whether applied on a building site or in a prefabrication (manufacturing) facility, and non-building applications. The material is also known as in-situ thermal insulation. The spray-applied polyurethane rigid cellular plastic thermal insulation is not to be used when the continuous service temperature of the substrate is outside the range of -60 °C to +80 °C. The test methods used to determine the material properties provide a means of comparing different cellular plastic thermal insulations. They are intended for use in specifications, product evaluations and quality control. They are not intended to predict end-use product performance.
Plastiques alvéolaires rigides — Mousse de polyuréthanne projetée pour l'isolation thermique — Partie 1: Spécifications des matériaux
Penjeni polimerni materiali - Brizgana poliuretanska pena za toplotno izolacijo - 1. del: Specifikacije materiala
Ta del standarda ISO 8873 določa minimalne zahteve in metode preskušanja za brizgano poliuretansko peno iz penjenega polimernega materiala, ki se uporablja kot toplotna izolacija v stavbah, ne glede na to, ali se uporablja na gradbišču ali v montažnem (proizvodnem) obratu, ali zunaj stavb. Material se imenuje tudi toplotna izolacija, izdelana na kraju samem.
Toplotna izolacija iz brizgane poliuretanske pene iz penjenega polimernega materiala se ne sme uporabljati, če je razpon stalne delovne temperature podlage zunaj območja do .
Metode preskušanja, uporabljene za določanje lastnosti materialov, zagotavljajo način za primerjavo različne toplotne izolacije iz brizgane poliuretanske pene. Namenjene so za uporabo pri specifikacijah, vrednotenju proizvodov in kontroli kakovosti.
Niso namenjene za napovedovanje lastnosti končnega proizvoda.
Brizgana poliuretanska pena iz penjenega polimernega materiala se mora uporabljati (namestiti) v skladu z
navodili proizvajalca in zahtevami iz standarda ISO 8873-2. Uporabe, zahteve za uporabo in omejitve uporabe so vključene v standard ISO 8873-2.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 8873-1:2015
01-marec-2015
Penjeni polimerni materiali - Brizgana poliuretanska pena za toplotno izolacijo - 1.
del: Specifikacije materiala
Rigid cellular plastics - Spray-applied polyurethane foam for thermal insulation - Part 1:
Material specifications
Plastiques alvéolaires rigides - Mousse de polyuréthanne projetée pour l'isolation
thermique - Partie 1: Spécifications des matériaux
Ta slovenski standard je istoveten z: ISO 8873-1:2006
ICS:
83.100 Penjeni polimeri Cellular materials
SIST ISO 8873-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 8873-1:2015
---------------------- Page: 2 ----------------------
SIST ISO 8873-1:2015
INTERNATIONAL ISO
STANDARD 8873-1
First edition
2006-12-15
Rigid cellular plastics — Spray-applied
polyurethane foam for thermal
insulation —
Part 1:
Material specifications
Plastiques alvéolaires rigides — Mousse de polyuréthanne projetée
pour l'isolation thermique —
Partie 1: Spécifications des matériaux
Reference number
ISO 8873-1:2006(E)
©
ISO 2006
---------------------- Page: 3 ----------------------
SIST ISO 8873-1:2015
ISO 8873-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2006 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 8873-1:2015
ISO 8873-1:2006(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 3
4.1 General requirements . 3
4.2 Categories . 3
5 Sampling . 4
5.1 General . 4
5.2 Preparation of sample panels . 4
5.3 Conditioning of sample panels . 4
5.4 Preparation of specimens . 4
6 Test methods . 5
6.1 Air permeance . 5
6.2 Apparent core density . 5
6.3 Compressive st
...
INTERNATIONAL ISO
STANDARD 8873-1
First edition
2006-12-15
Rigid cellular plastics — Spray-applied
polyurethane foam for thermal
insulation —
Part 1:
Material specifications
Plastiques alvéolaires rigides — Mousse de polyuréthanne projetée
pour l'isolation thermique —
Partie 1: Spécifications des matériaux
Reference number
ISO 8873-1:2006(E)
©
ISO 2006
---------------------- Page: 1 ----------------------
ISO 8873-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2006 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8873-1:2006(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 3
4.1 General requirements . 3
4.2 Categories . 3
5 Sampling . 4
5.1 General . 4
5.2 Preparation of sample panels . 4
5.3 Conditioning of sample panels . 4
5.4 Preparation of specimens . 4
6 Test methods . 5
6.1 Air permeance . 5
6.2 Apparent core density . 5
6.3 Compressive strength . 5
6.4 Dimensional stability . 5
6.5 Surface burning characteristics . 5
6.6 Open-cell content: Volume . 5
6.7 Initial thermal resistance . 5
6.8 Long-term thermal resistance (LTTR) . 6
6.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.