ISO 5832-11:2024

International
Standard
ISO 5832-11
Third edition
Implants for surgery — Metallic
materials —
Part 11:
Wrought titanium 6-aluminium
7-niobium alloy
Implants chirurgicaux — Produits à base de métaux —
Partie 11: Alliage à forger à base de titane, d'aluminium 6 et de
niobium 7
PROOF/ÉPREUVE
Reference number
ISO 5832-11:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 5832-11:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 5832-11:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Chemical composition . 1
5 Microstructure. 2
6 Mechanical properties . 2
7 Test methods . 2
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
iii

---------------------- Page: 3 ----------------------
ISO 5832-11:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database ava
...

ISO/DISPRF 5832-11:2023(E)
ISO/TC 150/SC 1/WG 4
Secretariat: DIN
Date: 2024-01-23
Implants for surgery — Metallic materials — —
Part 11:
Wrought titanium 6-aluminium 7-niobium alloy
Third edition
Date: 2023-04-24

---------------------- Page: 1 ----------------------
Implants chirurgicaux — Produits à base de métaux —
Partie 11: Alliage à forger à base de titane, d'aluminium 6 et de niobium 7
PROOF

---------------------- Page: 2 ----------------------
ISO/PRF 5832-11:2024(en)
© ISO 20232024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Fax: +41 22 749 09 47
EmailE-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved

iii

---------------------- Page: 3 ----------------------
ISO/PRF 5832-11:2024(en)
Contents
Foreword . v
Introduction. vi
Part 11: Wrought titanium 6-aluminium 7-niobium alloy .1
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Chemical composition .1
5 Microstructure .2
6 Mechanical properties .2
7 Test methods .2

© ISO 2024 – All rights reserved

iv

---------------------- Page: 4 ----------------------
ISO/PRF 5832-11:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall no
...