ISO 2417:2025
(Main)Leather — Physical and mechanical tests — Determination of the static absorption of water
Leather — Physical and mechanical tests — Determination of the static absorption of water
This document specifies a method for determining the water absorption of leather under static conditions. The method is applicable to all leather, particularly heavy leather.
Cuir — Essais physiques et mécaniques — Détermination de l'absorption statique d'eau
Le présent document spécifie une méthode permettant de déterminer l’absorption d’eau du cuir dans des conditions statiques. Cette méthode est applicable à tous les cuirs, notamment aux cuirs épais.
General Information
Standards Content (Sample)
International
Standard
ISO
IULTCS
IUP 7
Fourth edition
Leather — Physical and mechanical
2025-10
tests — Determination of the static
absorption of water
Cuir — Essais physiques et mécaniques — Détermination de
l'absorption statique d'eau
Reference numbers
IULTCS/IUP 7:2025(en) © ISO 2025
IULTCS/IUP 7:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
IULTCS/IUP 7:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Selection of leather specimen and test piece preparation . 2
7 Procedure . 2
8 Expression of results . 3
9 Test report . 3
iii
IULTCS/IUP 7:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO’s adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to further
the advancement of leather science and technology. IULTCS has three Commissions, which are responsible
for establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an
international standardizing body for the preparation of test methods for leather.
This document was prepared by the Physical Test Commission of the International Union of Leather
Technologists and Chemists Societies (IUP Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
It is based on IUP 7 published in J. Soc. Leather Tech. Chem. 84, p. 323, (2000) and declared an official method
of the IULTCS in March 2001.
This fourth edition cancels and replaces the third edition (ISO 2417:2016), which has been technically
revised.
The main changes are as follows:
— alignment with the changes and revised terminology in ISO 2418 and ISO 2419;
— addition of Clause 3.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of thes
...
Norme
internationale
ISO
IULTCS
IUP 7
Quatrième édition
Cuir — Essais physiques et
2025-10
mécaniques — Détermination de
l'absorption statique d'eau
Leather — Physical and mechanical tests — Determination of the
static absorption of water
Numéros de référence
IULTCS/IUP 7:2025(fr) © ISO 2025
IULTCS/IUP 7:2025(fr)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
IULTCS/IUP 7:2025(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 1
6 Sélection du spécimen de cuir et préparation de l’éprouvette . 2
7 Mode opératoire . 2
8 Expression des résultats . 3
9 Rapport d'essai . 3
iii
IULTCS/IUP 7:2025(fr)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n’avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l’adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir le lien suivant: www.iso.org/avant-propos.
L’IULTCS est une organisation mondiale de sociétés professionnelles des industries du cuir fondée en 1897
ayant pour mission de favoriser l’avancement des sciences et technologies du cuir. L’IULTCS a trois
commissions, qui sont responsables de l’établissement de méthodes internationales d’échantillonnage et
d’essai des cuirs. L’ISO reconnaît l’IULTCS en tant qu’organisme international à activités normatives pour
l’élaboration de méthodes d’essai relatives au cuir.
Le présent document a été élaboré par la Commission Essais Physiques de l'Union internationale des sociétés
de techniciens et chimistes du cuir (commission IUP, IULTCS), en collaboration avec le comité technique
(CEN) CEN/TC 289, Cuir, du Comité européen de normalisation, conformément à l'Accord de coopération
technique entre l'ISO et le CEN (Accord de Vienne).
Il est fondé sur le document IUP 7, publié dans le J. Soc. Leather Tech. Chem. 84, p. 323, (2000) et déclaré
méthode officielle de l'IULTCS en mars 2001.
Cette quatrième édition annule et remplace la troisième édition (ISO 2417:2016), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— mise à jour suivant les modifications et les révisions terminologiques de l’ISO 2418 et de l’ISO 2419;
— ajout de l'Article 3.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/members.html.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.