IEC 80369-5:2016/COR1:2017
(Corrigendum)Corrigendum 1 - Small bore connectors for liquids and gases in healthcare application - Part 5: Connectors for limb cuff inflation applications
Corrigendum 1 - Small bore connectors for liquids and gases in healthcare application - Part 5: Connectors for limb cuff inflation applications
Corrigendum 1 - Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé - Partie 5: Raccords destinés à des applications au gonflage de brassard
General Information
Relations
Standards Content (Sample)
IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 80369-5 IEC 80369-5
Edition 1.0 2016-03 Édition 1.0 2016-03
SMALL BORE CONNECTORS FOR LIQUIDS AND RACCORDS DE PETITE TAILLE POUR LIQUIDES
GASES IN HEALTHCARE APPLICATION – ET GAZ UTILISES DANS LE DOMAINE DE LA
SANTE –
Part 5: Connectors for limb cuff inflation
applications Partie 5: Raccords destinés à des applications
au gonf
...
This May Also Interest You
This document specifies the design and dimensions for two small-bore connectors intended to be used for connections in respiratory applications of medical devices and accessories. One connector (R1) is intended for use on medical devices and accessories subjected to pressures up to 15 kPa (e.g. a breathing system). The other connector (R2) is intended for use on medical devices and accessories subjected to higher pressures between 15 kPa and 600 kPa (e.g. oxygen therapy tubing).
NOTE 1 The pressure is related to pressure available at the source to which the medical device is connected.
NOTE 2 The intended application does not preclude the use of other connectors on medical devices or accessories within this application.
NOTE 3 Requirements for alternative connectors for this intended application are specified in ISO 80369-1.
This document does not specify requirements for the medical devices or accessories that use these connectors. Such requirements are given in device-specific standards.
NOTE 4 If a device-specific standard does not exist, the performance and material requirements specified in ISO 80369-1 can be used as guidance.
- Standard50 pagesEnglish languagesale 15% off
- Standard2 pagesEnglish and French languagesale 15% off
IEC TR 62653:2020 is available as IEC TR 62653:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TR 62653:2020 describes the technical recommendations for use of medical equipment in chronic Haemodialysis, Haemofiltration and Haemodiafiltration. These principles are important to be complied with to ensure safe, permissible and appropriate application. The term Haemodialysis is used in this document as synonym for all therapy modalities.
The scope can be applicable to the use of the medical equipment in home, acute and pediatrics environment. The scope may also be applicable to Sorbent Dialysis Systems.
The physician is responsible for the treatment prescription. However, the Organization administering the treatment is responsible for all resources, structures and processes used in connection with the treatment. These responsibilities will not be described here. The requirements of IEC 60601-2-16 ensure that medical electrical equipment used for extracorporeal renal replacement therapy operates with a high level of safety. Despite that high level of safety, however, some residual risk remains, related to medical-biological, physical-chemical and technical Hazards. The Organization administering the treatment is responsible for managing the residual risk. This document is not intended to be used as the basis of regulatory inspection or certification assessment activities. IEC TR 62653:2020 cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) update the relevant references to the new numbering scheme of the ISO 23500 family;
b) alignment with IEC 60601-1:2005 and IEC 60601-1:2005/AMD1:2012, IEC 62353:2014 and 60601-2-16:2018;
c) technical additions in several sections.
- Technical report36 pagesEnglish languagesale 15% off
- Technical report75 pagesEnglish languagesale 15% off
ISO 80369-1:2018 This document specifies general requirements for small-bore connectors, which convey liquids or gases in healthcare applications. These small-bore connectors are used in medical devices or accessories intended for use with a patient.
This document also specifies the healthcare fields in which these small-bore connectors are intended to be used.
These healthcare fields include, but are not limited to:
- breathing systems and driving gases;
- enteral;
- limb cuff inflation;
- neuraxial;
- intravascular or hypodermic.
This document provides the methodology to assess non-interconnectable characteristics of small-bore connectors based on their inherent design and dimensions in order to reduce the risk of misconnections between medical devices or between accessories for different applications as specified in this document as well as those that will be developed under future parts of the ISO 80369 series.
This document does not specify requirements for the medical devices or accessories that use these small-bore connectors. Such requirements are given in particular International Standards for specific medical devices or accessories.
NOTE 1 Clause 7 allows for additional designs of small-bore connectors for new applications for inclusion in the ISO 80369 series.
NOTE 2 Manufacturers are encouraged to incorporate the small-bore connectors specified in the ISO 80369 series into medical devices, medical systems or accessories, even if currently not required by the relevant particular medical device standards. It is expected that when the relevant particular medical device standards are revised, the risks associated with changing to the new small-bore connectors as specified in the ISO 80369 series of standards will be considered.
NOTE 3 The connectors specified in the ISO 80369 series are intended for use only in their specified application. Use of these connectors for other applications increases risk that a hazardous misconnection could occur.
NOTE 4 Manufacturers and responsible organizations are encouraged to report their experience with the small-bore connectors specified in the ISO 80369 series to the Secretariat of ISO/TC 210 so that this feedback can be considered during the revision of the relevant part of the ISO 80369 series.
- Standard31 pagesEnglish languagesale 15% off
- Standard34 pagesFrench languagesale 15% off
IEC 60601-2-16:2018 is also available as IEC 60601-2-16:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60601-2-16:2018 applies to the basic safety and essential performance of haemodialysis, haemodiafiltration and haemofiltration equipment. IEC 60601-2-16:2018 does not take into consideration the dialysis fluid control system of Haemodialysis equipment using regeneration of dialysis fluid and central delivery systems. It does however take into consideration the specific safety requirements of such haemodialysis equipment concerning electrical safety and patient safety. IEC 60601-2-16:2018 specifies the minimum safety requirements for haemodialysis equipment. These devices are intended for use either by medical staff or for use by the patient or other trained personnel under the supervision of medical expertise. IEC 60601-2-16:2018 includes all electromedical equipment that is intended to deliver a haemodialysis, haemodiafiltration and haemofiltration treatment to a patient suffering from kidney failure. This fifth edition cancels and replaces the fourth edition of IEC 60601-2-16, published in 2012. This edition includes the following significant technical changes with respect to the previous edition:
a) update of references to IEC 60601-1:2005 and IEC 60601-1:2005/AMD1:2012, of references and requirements to IEC 60601-1-2:2014, of references to IEC 60601-1-6:2010 and IEC 60601-1-6:2010/AMD1:2013, of references and requirements to IEC 60601-1-8:2006 and IEC 60601-1-8:2006/AMD1:2012, of references to IEC 60601-1-9:2007 and IEC 60601-1-9:2007/AMD1:2013, of references to IEC 60601-1-10:2007 and IEC 60601-1-10:2007/AMD1:2013 and of references to IEC 60601-1-11:2015;
b) widening of the scope;
c) editorial improvements;
d) addition of requirements for anticoagulant delivery means;
e) other few small technical changes.
- Standard236 pagesEnglish languagesale 15% off
- Standard156 pagesEnglish and French languagesale 15% off
IEC 60601-2-40:2016 applies to the basic safety and essential performance of electromyographs and evoked response equipment, hereafter referred to as ME equipment. ME equipment intended for transcutaneous electrical nerve stimulators and electrical muscle stimulators are excluded (covered by IEC 60601-2-10). This second edition cancels and replaces the first edition of IEC 60601-2-40 published in 1998. This edition constitutes a technical revision.
- Standard60 pagesEnglish and French languagesale 15% off
IEC 80369-5:2016 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in limb cuff inflation applications of medical devices and accessoires. Limb cuff inflation applications include connections between a sphygmomanometer and its cuff. The contents of the corrigenda 1 (2017) and 2 (2021) have been included in this copy.
- Standard89 pagesEnglish and French languagesale 15% off
IEC 60601-2-41:2009 applies to the basic safety and essential performance of surgical luminaires and luminaires for diagnosis. It amends and supplements IEC 60601-1 (third Edition 2005), hereinafter referred to as the general standard. This second edition cancels and replaces the first edition published in 2000. This edition constitutes a technical revision to be consistent with the third edition of the IEC 60601-1.
- Standard77 pagesEnglish and French languagesale 15% off
- Standard163 pagesEnglish and French languagesale 15% off
Covers copper-clad Invar material of nominal thickness from 0,1 mm to 2,4 mm supplied in rolls or produced in sheets.
- Standard9 pagesEnglish and French languagesale 15% off
IEC 60601-2-24:2012 applies to the basic safety and essential performance of infusion pumps and volumetric infusion controllers. This standard applies to administration sets insofar as their characteristics influence the basic safety or essential performance of infusion pumps and volumetric infusion controllers. However this standard does not specify requirements or tests for other aspects of administration sets. This particular standard specifies the requirements for enteral nutrition pumps, infusion pumps, infusion pumps for ambulatory use, syringe or container pumps, volumetric infusion controllers and volumetric infusion pumps. This particular standard does not apply to the following: devices specifically intended for diagnostic or similar use; devices for extracorporeal circulation of blood; implantable devices; equipment specifically intended for diagnostic use within urodynamics; equipment specifically intended for diagnostic use within male impotence testing; and devices covered by ISO 28620. This second edition cancels and replaces the first edition of IEC 60601-2-24. This edition constitutes a technical revision according to IEC 60601-1:2005+A1:2012 with new clause numbering, including usability and alarms.
- Standard123 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.