IEC 60745-2-17:2003

INTERNATIONAL IEC
STANDARD
60745-2-17
Second edition
2003-01
Hand-held motor-operated electric tools –
Safety –
Part 2-17:
Particular requirements for routers
and trimmers
Outils électroportatifs à moteur –
Sécurité –
Partie 2-17:
Règles particulières pour les défonçeuses et
affleureuses
Reference number
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.

Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,

edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the
base publication incorporating amendment 1 and the base publication incorporating
amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/catlg-e.htm) enables
you to search by a variety of criteria including text searches, technical
committees and date of publication. On-line information is also available on
recently issued publications, withdrawn and replaced publications, as well as
corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/JP.htm) is also
available by email. Please contact the Customer Service Centre (see below) for
further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:
Email: custserv@iec.ch
Tel: +41 22 919 02 11
Fax: +41 22 919 03 00
INTERNATIONAL IEC
STANDARD
60745-2-17
Second edition
2003-01
Hand-held motor-operated electric tools –
Safety –
Part 2-17:
Particular requirements for routers
and trimmers
Outils électroportatifs à moteur –
Sécurité –
Partie 2-17:
Règles particulières pour les défonçeuses et
affleureuses
 IEC 2003  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch  Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
J
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue

– 2 – 60745-2-17  IEC:2003(E)

INTERNATIONAL ELECTROTECHNICAL COMMISSION

___________
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –

SAFETY –
Part 2-17: Particular requirements for routers and trimmers

FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60745-2-17 has been prepared by subcommittee 61F: Safety of
hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household
and similar electrical appliances
This second edition cancels and replaces the first edition published in 1989, of which it
constitutes a technical revision.
The text of this standard is based on the following documents:

FDIS Report on voting
61F/468/FDIS 61F/492/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives.
This Part 2-17 is to be used in conjunction with the third edition of IEC 60745-1: Safety of
hand-held motor-operated electric tools – Part 1: General requirements. When this standard
states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted
accordingly.
60745-2-17 © IEC:2003(E) – 3 –

NOTE in this standard, the following print types are used:

– requirements: in roman type;

– test specifications: in italic type;

– notes: in smaller roman type.

Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101; additional
annexes are lettered AA, BB, etc.

The committee has decided that the contents of this publication will remain unchanged until

January 2007. At this date, the publication will be

• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

– 4 – 60745-2-17  IEC:2003(E)

HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –

SAFETY –
Part 2-17: Particular requirements for routers and trimmers

1 Scope
This clause of Part 1 is applicable, except as follows:
1.1 Addition:
This standard applies to routers and trimmers.
2 Normative references
This clause of Part 1 is applicable.
3 Definitions
This clause of Part 1 is applicable, except as follows:
Additional definitions:
3.101
router
tool designed to be fitted with rotary cutter and with a base that allows control of cutting slots
into or shaping the edge of various materials
3.102
trimmer
tool designed to be fitted with rotary cutter and a base that allows for control of trimming the
edge of laminate sheet or similar materials
4 General requirements
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable.
6 Void
7 Classification
This clause of Part 1 is applicable.

60745-2-17 © IEC:2003(E) – 5 –

8 Marking and instructions
This clause of Part 1 is applicable except as follows:

8.1 Addition:
– rated no-load speed in revolutions per minute.

8.12.2 a) Addition:
7) Details of the type of cutters for which the tool is designed

8) Draw attention to the necessity for using bits of the correct shank diameter suitable for the

speed of the tool
9) Information concerning the diameter of shank for which the collet is designed
9 Protection against access to live parts
This clause of Part 1 is applicable.
10 Starting
This clause of Part 1 is applicable.
11 Input and current
This clause of Part 1 is applicable.
12 Heating
This clause of Part 1 is applicable, except as follows:
12.4 Replacement:
The tool is operated for 15 cycles, each cycle comprising a period of continuous operation of
1 min and a
...