IEC 61169-1:2013
(Main)Radio frequency connectors - Part 1: Generic specification - General requirements and measuring methods
Radio frequency connectors - Part 1: Generic specification - General requirements and measuring methods
IEC 61169-1:2013, which is a generic specification, relates to radio frequency connectors for r.f. transmission lines for use in telecommunications, electronics and similar equipment. It provides the basis for the sectional standards, which apply to individual connector types. It is intended to establish uniform concepts and procedures concerning:
- terminology;
- standard ratings and characteristics;
- testing and measuring procedures concerning electrical, mechanical and climatic properties;
- classification of connectors with regard to climatic testing procedures involving temperature and humidity.
The test methods and procedures of this standard are intended for acceptance and type approval testing. This second edition cancels and replaces the first edition, published in 1992, its Amendments 1 (1996) and 2 (1997). This edition constitutes a technical revision. With respect to the previous edition, tests methods have been updated as well as terminology. The contents of the corrigendum of February 2016 have been included in this copy.
Connecteurs pour fréquences radioélectriques - Partie 1: Spécification générique - Exigences générales et méthodes de mesure
L'IEC 61169-1:2013 est une spécification générique, qui s'applique aux connecteurs pour fréquences radioélectriques de lignes de transmission pour fréquences radioélectriques destinés à être utilisés dans des équipements de télécommunications, électroniques et similaires. Elle fournit la base de spécifications intermédiaires qui s'appliquent à des types de connecteurs distincts. Elle a pour objet de fixer des concepts et des procédures uniformes concernant:
- la terminologie;
- les valeurs assignées et les caractéristiques;
- les procédures d'essai et de mesure concernant les propriétés électriques, mécaniques et climatiques;
- la classification des connecteurs d'après les procédures d'essais climatiques relatives à la température et à l'humidité. Les méthodes et les procédures d'essai de la présente norme sont d'abord prévues pour des essais d'approbation de type. Cette deuxième édition annule et remplace la première édition parue en 1992, ainsi que ses amendements 1 (1996) et 2 (1997). Cette édition constitue une révision technique. Par rapport à l'édition antérieure, les méthodes d'essai ainsi que la terminologie ont été mises à jour. Le contenu du corrigendum publié en Février 2016 est inclus.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61169-1 ®
Edition 2.0 2013-07
INTERNATIONAL
STANDARD
colour
inside
Radio frequency connectors –
Part 1: Generic specification – General requirements and measuring methods
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
IEC 61169-1 ®
Edition 2.0 2013-07
INTERNATIONAL
STANDARD
colour
inside
Radio frequency connectors –
Part 1: Generic specification – General requirements and measuring methods
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
XA
ICS 33.120.30 ISBN 978-2-8322-0925-7
– 2 – 61169-1 © IEC:2013(E)
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
3.1 General, parts of connectors . 8
3.2 Basic connector terms . 9
3.3 Constructional terms . 10
3.4 Sealing . 11
3.5 Miscellaneous terms . 11
3.6 General electrotechnical terms . 12
4 Units, symbols and dimensions . 12
4.1 Units and symbols . 12
4.2 Dimensions . 13
4.2.1 Details to be provided in relevant specifications . 13
4.2.2 Dimensional units to be used in specifications . 13
5 Standards ratings and characteristics . 13
6 Classifications into climatic categories . 13
7 IEC type designation . 14
8 Testing . 14
9 Test methods. 14
9.1 Mechanical inspection . 14
9.1.1 Visual inspection . 14
9.1.2 Dimensions. 15
9.2 Electrical tests and measuring procedures . 15
9.2.1 Return loss . 15
9.2.2 Power rating . 19
9.2.3 Contact resistance, outer conductor and centre conductor continuity
(mated cabled connectors) . 20
9.2.4 Centre and outer conductor contact continuity under severe
mechanical conditioning . 22
9.2.5 Insulation resistance . 22
9.2.6 Voltage proof . 23
9.2.7 Screening effectiveness . 24
9.2.8 Discharge test (corona test) . 24
9.2.9 Intermodulation level (PIM) . 25
9.2.10 Surge withstand . 26
9.3 Mechanical tests and measuring procedures . 26
9.3.1 General . 26
9.3.2 Soldering . 26
9.3.3 Vibration . 26
9.3.4 Insertion force (resilient contacts) . 27
9.3.5 Centre contact captivation . 28
9.3.6 Engagement and separation forces and torques . 28
9.3.7 Effectiveness of clamping device against cable rotation (nutation of
cable end) . 29
9.3.8 Effectiveness of clamping device against cable pulling . 29
61169-1 © IEC:2013(E) – 3 –
9.3.9 Effectiveness of clamping device against cable bending . 30
9.3.10 Effectiveness of clamping device against cable torsion . 31
9.3.11 Strength of coupling mechanism . 32
9.3.12 Safety wire hole pull-out bending moment (and shearing force) . 32
9.3.13 Bump . 33
9.3.14 Shock . 34
9.3.15 Mechanical endurance . 35
9.4 Climatic conditionings and tests . 35
9.4.1 Conditionings . 35
9.4.2 Climatic sequence . 36
9.4.3 Damp heat, steady state . 37
9.4.4 Change of temperature . 37
9.4.5 High temperature endurance . 38
9.4.6 Low temperature endurance . 39
9.4.7 Sealing non-hermetic sealed connectors. 40
9.4.8 Hermetically sealed connectors . 40
9.4.9 Water immersion test . 41
9.4.10 Salt mist . 43
9.4.11 Resistance to solvents and contaminating fluids . 43
9.4.12 Sulphur dioxide test . 45
10 Quality assessment . 46
10.1 General . 46
10.2 Quality assessment steps . 46
10.2.1 Primary stage of manufacture . 46
10.2.2 Structurally similar components . 46
10.2.3 General principle for obtaining quality conformance . 46
10.3 Test schedule and inspection requirements . 46
10.3.1 Acceptance tests . 46
10.3.2 Periodic tests. 48
10.4 Procedures for quality conformance . 49
10.4.1 Quality conformance inspection . 49
10.4.2 Quality conformance and its maintenance . 49
10.5 Test and measurement procedures . 49
10.5.1 General . 49
10.5.2 Schedule of basic test groupings for acceptance and periodic tests . 50
10.6 Specifications . 50
10.6.1 Specification structures . 50
10.6.2 Sectional specification (SS) . 50
10.6.3 Detail specification (DS) . 50
10.6.4 Blank detail specification . 51
10.6.5 Blank detail specification pro-forma for XXXX connectors . 52
11 Marking . 57
11.1 Marking of component . 57
11.2 Marking and contents of package . 57
Annex A (informative) Simulated sea-water solution for use with salt mist test (marine
environment, see 9.4.10.3) . 58
Bibliography . 59
– 4 – 61169-1 © IEC:2013(E)
Figure 1 – graphical symbols . 16
Figure 2 – General principle . 16
Figure 3 – Measuring set-up for two-connector procedure . 17
Figure 4 – Example of a time domain reflectometer measurement recording . 18
Figure 5 – Equipment set-up for the measurement of reflection in time domain . 19
Figure 6 – Possible test arrangements . 23
Figure 7 – Measuring circuit for the discharge test . 25
Figure 8 – Test arrangement for nutation . 29
Figure 9 – Test arrangement for pulling .
...
IEC 61169-1 ®
Edition 2.0 2013-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency connectors –
Part 1: Generic specification – General requirements and measuring methods
Connecteurs pour fréquences radioélectriques –
Partie 1: Spécification générique – Exigences générales et méthodes de mesure
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 15
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
La recherche avancée permet de trouver des publications IEC 65 000 entrées terminologiques électrotechniques, en anglais
en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des
comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées
projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et
CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 61169-1 ®
Edition 2.0 2013-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency connectors –
Part 1: Generic specification – General requirements and measuring methods
Connecteurs pour fréquences radioélectriques –
Partie 1: Spécification générique – Exigences générales et méthodes de mesure
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-3230-9
– 2 – IEC 61169-1:2013 © IEC:2013
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
3.1 General, parts of connectors . 8
3.2 Basic connector terms . 9
3.3 Constructional terms . 10
3.4 Sealing . 11
3.5 Miscellaneous terms . 11
3.6 General electrotechnical terms . 12
4 Units, symbols and dimensions . 12
4.1 Units and symbols . 12
4.2 Dimensions . 13
4.2.1 Details to be provided in relevant specifications . 13
4.2.2 Dimensional units to be used in specifications . 13
5 Standards ratings and characteristics . 13
6 Classifications into climatic categories . 13
7 IEC type designation . 14
8 Testing . 14
9 Test methods . 14
9.1 Mechanical inspection. 14
9.1.1 Visual inspection . 14
9.1.2 Dimensions . 15
9.2 Electrical tests and measuring procedures . 15
9.2.1 Return loss . 15
9.2.2 Power rating . 19
9.2.3 Contact resistance, outer conductor and centre conductor continuity
(mated cabled connectors) . 20
9.2.4 Centre and outer conductor contact continuity under severe
mechanical conditioning . 22
9.2.5 Insulation resistance . 22
9.2.6 Voltage proof . 23
9.2.7 Screening effectiveness . 24
9.2.8 Discharge test (corona test) . 24
9.2.9 Intermodulation level (PIM). 25
9.2.10 Surge withstand . 26
9.3 Mechanical tests and measuring procedures . 26
9.3.1 General . 26
9.3.2 Soldering . 26
9.3.3 Vibration . 26
9.3.4 Insertion force (resilient contacts) . 27
9.3.5 Centre contact captivation . 28
9.3.6 Engagement and separation forces and torques . 28
9.3.7 Effectiveness of clamping device against cable rotation (nutation of
cable end) . 29
9.3.8 Effectiveness of clamping device against cable pulling . 29
9.3.9 Effectiveness of clamping device against cable bending . 30
9.3.10 Effectiveness of clamping device against cable torsion . 31
9.3.11 Strength of coupling mechanism . 32
9.3.12 Safety wire hole pull-out bending moment (and shearing force) . 32
9.3.13 Bump . 33
9.3.14 Shock . 34
9.3.15 Mechanical endurance . 35
9.4 Climatic conditionings and tests . 35
9.4.1 Conditionings . 35
9.4.2 Climatic sequence . 36
9.4.3 Damp heat, steady state . 37
9.4.4 Change of temperature . 37
9.4.5 High temperature endurance . 38
9.4.6 Low temperature endurance . 39
9.4.7 Sealing non-hermetic sealed connectors . 40
9.4.8 Hermetically sealed connectors . 40
9.4.9 Water immersion test . 41
9.4.10 Salt mist . 43
9.4.11 Resistance to solvents and contaminating fluids . 43
9.4.12 Sulphur dioxide test . 45
10 Quality assessment . 46
10.1 General . 46
10.2 Quality assessment steps . 46
10.2.1 Primary stage of manufacture . 46
10.2.2 Structurally similar components . 46
10.2.3 General pri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.