IEC 63137-1:2019/COR1:2020
(Corrigendum)Corrigendum 1 - Standard test radio-frequency connectors - Part 1: Generic specification - General requirements and test methods
Corrigendum 1 - Standard test radio-frequency connectors - Part 1: Generic specification - General requirements and test methods
Corrigendum 1 - Connecteurs d’essai normalisés pour fréquences radioélectriques - Partie 1: Spécification générique - Exigences générales et méthodes d’essai
General Information
Relations
Standards Content (Sample)
IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 63137-1 IEC 63137-1
Edition 1.0 2019-08 Édition 1.0 2019-08
STANDARD TEST RADIO-FREQUENCY CONNECTEURS D'ESSAI NORMALISÉS POUR
CONNECTORS – FRÉQUENCES RADIOÉLECTRIQUES–
Part 1: Generic specification - General Partie 1: Spécification générique – Exigences
requirements a
...
This May Also Interest You
IEC TR 61169-1-8:2025 provides a test method for voltage standing wave ratio (VSWR, hereinafter) of single RF connector by double-connector method. This document is applicable to single RF cable connectors and single microstrip RF connectors as well as single adapters if an estimation of the VSWR of a single completely installed RF-connector is used and a time domain feature is not available on the vector network analyzer.
- Technical report18 pagesEnglish languagesale 15% off
IEC 61169-74:2025, which is a Sectional Specification (SS), provides information and rules for the preparation of Detail Specifications (DS) for series HN RF coaxial connectors with screw coupling with a characteristic impedance of 50 Ω.
This document prescribes mating face dimensions for high performance connectors (grade 2), dimensional details of standard test connectors (grade 0), gauging information and tests selected from IEC 61169-1, applicable to all Detail Specifications relating to series HN RF connectors.
This document indicates recommended performance characteristics which are considered when writing a Detail Specification and it covers test schedules and inspection requirements for assessment levels M and H.
The series HN connectors are intended to be used in microwave transmission systems and can be connected with all kinds of RF cables and microstrips. The operating frequency is up to 6 GHz.
- Standard25 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
- Standard50 pagesEnglish and French languagesale 15% off
IEC 61169-64:2025, which is a sectional specification (SS), provides information for the preparation of detail specifications (DS) for coaxial connectors with 0,8 mm inner diameter of the outer conductor, characteristic impedance of 50 Ω, and with screw coupling. These connectors are referred to below as type 0,8 connectors. They are used in telecommunications technology as well as in test and measurement applications for operating frequencies up to 145 GHz.
This document describes mating face dimensions for high performance connectors (grade 1) and standard test connectors (grade 0), gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to type 0,8 connectors.
This document indicates the recommended performance characteristics to consider when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
This second edition cancels and replaces the first edition published in 2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) upgrading of the inferior connector class to a grade 1 “high performance connector”;
b) alignment of the mating face dimensions as well as the ratings and characteristics with the precision 0,8 mm connectors specified in the IEEE 287.1-2021 and IEEE 287.3-2021 standards;
c) figures: true-to-scale design; change of datum system for tolerances; introduction of an additional dimension;
d) gauge pins: correction of dimensions and test procedures;
e) simplification of the clauses on quality assessment (Clause 5), preparation of a detail specification (Clause 6), and marking (Clause 7) by making direct reference to the generic specification IEC 61169-1;
f) introduction of an optional design for the coupling nut.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
- Standard33 pagesEnglish and French languagesale 15% off
IEC 61169-23:2025, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for pin and socket connector for use with 3,5 mm rigid precision coaxial lines with inner diameter of outer conductor 3,5 mm (0,137 8 in).
This document specifies mating face dimensions for high performance connectors – grade 1, dimensional details of standard test connectors – grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series 3,5 mm RF connectors.
This document indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
These connectors are constructed so as to affix on the 50 Ω, 3,5 mm rigid precision coaxial line described in IEC 60457-5, and to provide low reflection to 34 GHz. These connectors can be intermated with SMA (IEC 61169-15) and 2,92 mm (IEC 61169-35) connectors.
- Standard22 pagesEnglish languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
- Standard45 pagesEnglish and French languagesale 15% off
IEC TS 61169-1-7:2025 relates to radio frequency connectors for RF transmission lines for use in telecommunications, electronics and similar equipment.
This document sets out the provisions for a report on the uncertainty specifications for insertion loss measurements, which apply to individual connector types, by vector network analyzers (VNAs). It is intended to establish concepts and procedures considering
– testing and measuring procedures concerning frequency domain electrical properties, and
– uncertainty specifications of VNAs measurements for insertion loss of RF connectors.
The test methods and procedures of this document are intended for acceptance and type approval testing.
- Technical specification11 pagesEnglish languagesale 15% off
IEC 61169-1-9:2025 specifies test methods for the safety wire hole pull-out of RF connectors.
This document is applicable to the connectors with safety wire holes.
- Standard17 pagesEnglish and French languagesale 15% off
IEC 63185:2025 relates to a measurement method for complex permittivity of dielectric substrates at microwave and millimeter-wave frequencies. This method has been developed to evaluate the dielectric properties of low-loss materials used in microwave and millimeter-wave circuits and devices. It uses higher-order modes of a balanced-type circular disk resonator and provides broadband measurements of dielectric substrates by using one resonator, where the effect of excitation holes and that of fringing fields are taken into account accurately on the basis of the mode-matching analysis.
This second edition cancels and replaces the first edition published in 2020. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the upper limit of the applicable frequency range has been extended from 110 GHz to 170 GHz;
b) circular disk resonators used for the measurements now include one with waveguide interfaces;
c) in calculating the complex permittivity from the measured resonant properties, the fringing fields are now accurately taken into account based on the mode-matching analysis.
- Standard28 pagesEnglish and French languagesale 15% off
IEC 61169-10:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series SMB RF coaxial connectors with snap-on coupling with a characteristic impedance of 50 Ω.
This document prescribes mating face dimensions for high performance connectors – grade 2, dimensional details of standard test connectors − grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series SMB RF connectors.
This document indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
The series SMB connectors are used to connect with all kinds of RF cables and microstrips in microwave transmission systems. The operating frequency is up to 4 GHz.
- Standard52 pagesEnglish and French languagesale 15% off
IEC 63138-2:2023, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for MQ4 series circular connectors with four RF channels, as well as a detailed specification of the blank format. An MQ4 series circular connector with 50 Ω nominal impedance has four RF channels which can be engaged and disengaged at the same time. There are two versions of plug connectors, one is a quick-lock version, and the other is a threaded version. The socket connector provides two coupling mechanisms, a quick-lock and a threaded coupling. MQ4 series circular connectors can be used in mobile communication systems and in other communication equipment. This document also specifies the mating face dimensions and gauging information of MQ4 series circular connectors, and tests selected from IEC 63138-1, applicable to all detail specifications relating to MQ4 series circular connectors.
- Standard94 pagesEnglish languagesale 15% off
- Standard58 pagesEnglish and French languagesale 15% off
IEC 61169-71:2022, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connector, typically for use in 50 Ω radio communication systems, type NEX10® .
This document describes mating face dimensions for general purpose connectors (grade 2), dimensional details of standard test connectors (grade 1), gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to type NEX10® RF coaxial connectors.
This document indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
- Standard66 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...