Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines

IEC 61969-1:2011 contains design guidelines for outdoor enclosures and is applicable over a wide field of mechanical, electromechanical and electronic equipment and its installation where a modular design is used. The objective of this standard is to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations. These enclosures are considered to contain any equipment and provide protection for the outdoor installed facilities against unwanted environmental impacts. The installed equipment may be, but is not limited to, subracks according to IEC 60917-2-2 or IEC 60297-3-101. This second edition cancels and replaces the first edition issued in 1999. It constitutes a technical revision. The main technical changes with regard to the previous edition are as follows:
- Addition of design guidance for thermal management and noise suppression as thermal/noise management is often considered a basic requirement of an empty outdoor enclosure. If thermal management components are included in the product, the environmental impact may become the responsibility of the empty outdoor enclosure manufacturer. Therefore the acoustic limitations shall be observed. Typically, the user of the empty outdoor enclosure follows the local regulatory acoustic requirements (sound power and/or sound pressure). Acoustic measurements may be performed on the empty outdoor enclosure fitted with thermal management components only or, if agreed between manufacturer and user at the final stage of the application specific installation.
- Historically, Ed 1 intended to create a market for standardized empty outdoor enclosures offered by multiple vendors. Detail standards such as IEC 61969-2-1 Ed 1 and IEC 61969-2-2 Ed 1 were issued to guide users to preferred and available solutions. However, development showed that this intend (created with user's participation) was not satisfying the user's expectations. Consequently, the detail standards IEC 61969-2-1 Ed 1 and IEC 61969-2-2 Ed 1 will be withdrawn when IEC 61969-2 Ed 2 is issued. The IEC 61969-2 Ed 2 co-ordination dimensions are based on IEC 60917-1. The definition outdoor cases and outdoor cabinets are merged into the definition outdoor enclosures.

Structures mécaniques pour équipment électronique - Enveloppes de plein air - Partie 1: Lignes directrices pour la conception

La CEI 61969-1:2011 fournit des lignes directrices pour la conception des enveloppes de plein air et s'applique à un vaste domaine d'équipement mécanique, électromécanique et électronique et à leur installation en configuration modulaire. Le but de cette norme est de fournir un ensemble de spécifications pour les enveloppes, spécialement pour ce qui concerne les contraintes propres aux applications de plein air pour une utilisation à poste fixe dans les lieux exposés aux intempéries. Ces enveloppes sont supposées contenir des équipements et protéger les installations situées en plein air contre les effets environnementaux indésirables. L'équipement installé peut, mais sans que ce soit limitatif, correspondre dimensionnellement aux bacs selon la CEI 60917-2-2 ou la CEI 60297-3-101. Cette deuxième édition annule et remplace la première édition, parue en 1999, dont elle constitue une révision technique. Les principaux changements techniques par rapport à l'édition précédente sont les suivants:
- Ajout de lignes directrices pour la conception de la gestion thermique et la suppression du bruit, puisque la gestion thermique/bruit sont souvent considérés comme correspondant à une exigence fondamentale d'une enveloppe de plein air vide. Si les composantes de la gestion thermique sont incluses dans la définition, l'impact environnemental peut devenir de la responsabilité du fournisseur de l'enveloppe de plein air vide. Par conséquent, les limites acoustiques doivent être observées. Généralement, l'utilisateur de l'enveloppe de plein air vide suit les exigences acoustiques réglementaires locales (puissance sonore et/ou pression sonore). Les mesures acoustiques peuvent être réalisées sur l'enveloppe de plein air vide équipée des composantes de gestion thermique uniquement ou, si cela est convenu entre le fournisseur et l'utilisateur à l'étape finale de l'installation spécifique à l'application.
- À l'origine, l'Éd 1 était prévue pour créer un marché pour les enveloppes de plein air vide que proposaient de nombreux vendeurs. Des normes particulières telles que la CEI 61969-2-1 Éd 1 et la CEI 61969-2-2 Éd 1 devaient orienter les utilisateurs vers des solutions préférentielles et disponibles sur le marché. Toutefois, le développement a montré que cet objectif (élaboré avec la participation de l'utilisateur) n'a pas répondu aux attentes de l'utilisateur. En conséquence, les normes particulières CEI 61969-2-1 Éd 1 et CEI 61969-2-2 Éd 1 seront supprimées au moment où sera publiée la CEI 61969-2 Éd 2. Les dimensions de coordination faisant l'objet de la CEI 61969-2 Éd 2 sont fondées sur la CEI 60917-1. La définition des coffrets de plein air et celle des armoires de plein air ont fusionné pour donner lieu à la définition des enveloppes de plein air.

General Information

Status
Published
Publication Date
16-Nov-2011
Current Stage
DELPUB - Deleted Publication
Start Date
31-Aug-2017
Completion Date
12-May-2020
Ref Project

Relations

Buy Standard

Standard
IEC 61969-1:2011 - Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines Released:11/17/2011
English and French language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 61969-1 ®
Edition 2.0 2011-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Mechanical structures for electronic equipment – Outdoor enclosures –
Part 1: Design guidelines
Structures mécaniques pour équipement électronique – Enveloppes de plein
air –
Partie 1: Lignes directrices pour la conception

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or

IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.

Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette

publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61969-1 ®
Edition 2.0 2011-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Mechanical structures for electronic equipment – Outdoor enclosures –
Part 1: Design guidelines
Structures mécaniques pour équipement électronique – Enveloppes de plein
air –
Partie 1: Lignes directrices pour la conception

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX L
ICS 31.240 ISBN 978-2-88912-791-7

– 2 – 61969-1  IEC:2011
CONTENTS
FOREWORD . 3

INTRODUCTION . 5

1 Scope . 6

2 Normative references . 7

3 Terms and definitions . 8

4 Dimensions . 9

5 Environmental requirements and tests, safety aspects. 9

5.1 Classification of environmental conditions . 9
5.2 Static load . 10
5.3 Dynamic stress . 10
5.4 Seismic performance . 10
6 Electromagnetic shielding . 10
7 Thermal management and acoustic noise suppression . 11

Figure 1 – Typical outdoor enclosure . 6
Figure 2 – Locations of outdoor enclosures . 8

Table 1 – Environmental conditions . 9
Table 2 – Safety aspects . 10

61969-1  IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT –

OUTDOOR ENCLOSURES –
Part 1: Design guidelines
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 61969-1 has been prepared by subcommittee 48D: Mechanical
structures for electronic equipment, of IEC technical committee 48: Electromechanical
components and mechanical structures for electronic equipment.
This second edition cancels and replaces the first edition issued in 1999. It constitutes a
technical revision.
The main technical changes with regard to the previous edition are as follows:
a) Addition of design guidance for thermal management and noise suppression as
thermal/noise management is often considered a basic requirement of an empty outdoor
enclosure. If thermal management components are included in the product, the
environmental impact may become the responsibility of the empty outdoor enclosure
manufacturer. Therefore the acoustic limitations shall be observed.

– 4 – 61969-1  IEC:2011
Typically, the user of the empty outdoor enclosure follows the local regulatory acoustic

requirements (sound power and/or sound pressure). Acoustic measurements may be

performed on the empty outdoor enclosure fitted with thermal management components

only or, if agreed between manufacturer and user at the final stage of the application

specific installation.
b) Historically, Ed 1 intended to create a market for standardized empty outdoor enclosures

offered by multiple vendors. Detail standards such as IEC 61969-2-1 Ed 1 and IEC 61969-

2-2 Ed 1 were issued to guide users to preferred and available solutions.

However, development showed that this intend (created with user’s participation) was not
satisfying the user’s expectations.

Consequently, the detail standards IEC 61969-2-1 Ed 1 and IEC 61969-2-2 Ed 1 will be
withdrawn when IEC 61969-2 Ed 2 is issued. The IEC 61969-2 Ed 2 co-ordination dimensions
are based on IEC 60917-1. The definition outdoor cases and outdoor cabinets are merged
into the definition outdoor enclosures.
The text of this standard is based on the following documents:
FDIS Report on voting
48D/488/FDIS 48D/498/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 61969, under the general title, Mechanical structures for electronic
equipment – Outdoor enclosures, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61969-1  IEC:2011 – 5 –
INTRODUCTION
This standard is intended as a generic guide for the development of further standards. The

products covered are empty enclosures to be equipped with application-specific solutions to

be used at non-weather protected locations above ground. This standard is followed by a co-

ordination dimension standard (IEC 61969-2 Ed 2) and an environmental requirements and

tests, safety aspect standard (IEC 61969-3 Ed 2).

– 6 – 61969-1  IEC:2011
MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT –

OUTDOOR ENCLOSURES –
Part 1: Design guidelines
1 Scope
This part of IEC 61969 contains design
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.