Nanomanufacturing - Key control characteristics - Part 6-18: Graphene-based material - Functional groups: TGA-FTIR

IEC TS 62607-6-18:2022(E) establishes a standardized method to determine the chemical key control characteristic
functional groups  for functionalized graphene-based material and graphene oxide by
thermogravimetry analysis (TGA) coupled with Fourier transform infrared spectroscopy (FTIR), referred to as TGA-FTIR.  The content of functional groups is derived by changes in mass of the sample as a function of temperature using TGA. Materials evolved during these mass changes are then analysed using coupled FTIR to identify functional groups.
The functional groups determined according to this document will be listed as a key control characteristic in the blank detail specification for graphene IEC 62565-3-1 for graphene powder.
The method is applicable for functionalized graphene powder and graphene oxide that can be pyrolysed and gasified with elevated temperature during TGA.
Typical application areas are quality control for graphene manufacturers, and product selection for downstream users.

General Information

Status
Published
Publication Date
13-Dec-2022
Current Stage
PPUB - Publication issued
Start Date
13-Jan-2023
Completion Date
14-Dec-2022
Ref Project

Buy Standard

Technical specification
IEC TS 62607-6-18:2022 - Nanomanufacturing - Key control characteristics - Part 6-18: Graphene-based material - Functional groups: TGA-FTIR Released:12/14/2022
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TS 62607-6-18 ®
Edition 1.0 2022-12
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –
Part 6-18: Graphene-based material – Functional groups: TGA-FTIR
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62607-6-18 ®
Edition 1.0 2022-12
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Key control characteristics –

Part 6-18: Graphene-based material – Functional groups: TGA-FTIR

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 07.120 ISBN 978-2-8322-6223-8

– 2 – IEC TS 62607-6-18:2022  IEC 2022
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General . 9
4.1 Measurement principle . 9
4.2 Sample preparation method . 9
4.3 Measurement system . 9
4.4 Description of measurement equipment . 9
4.5 Supporting materials . 9
4.6 Ambient conditions during measurement . 10
5 Measurement procedure . 10
5.1 Calibration of measurement equipment . 10
5.2 Detailed protocol of the measurement procedure . 10
6 Data analysis . 11
7 Results to be reported . 12
7.1 General . 12
7.2 Product or sample identification . 12
7.3 Test conditions . 12
7.4 Measurement specific information . 12
7.5 Test results . 12
Annex A (informative) Format of the test report . 13
Annex B (informative) Case study: Data analysis . 15
B.1 Confirmation of characteristic temperature points from TGA curve . 15
B.2 Analysis of FTIR spectra obtained at different ashing temperatures . 15
B.3 Analysis of FTIR spectra obtained by TGA-FTIR measurements . 16
B.4 Confirmation and quantification of the functional groups . 17
Bibliography . 19

Figure 1 – Flow chart of data analysis . 11
Figure B.1 – Weight loss curve (left) obtained from TGA-FTIR measurement and
corresponding differential weight loss curve (right) . 15
Figure B.2 – FTIR spectra corresponding to different ashing temperature points . 15
Figure B.3 – A 3D FTIR spectrum obtained by one FTIR-TGA measurement . 16
Figure B.4 – Absorption dynamics of each gas component . 17
Figure B.5 – Absorption dynamics of each gas component . 17
Figure B.6 – Weight loss dynamics of each gas component . 18

Table A.1 – Product identification (in accordance with IEC 62565-3-1) . 13
Table A.2 – General material description (in accordance with IEC 62565-3-1). 13
Table A.3 – Test information . 14
Table A.4 – Measurement results . 14

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
NANOMANUFACTURING – KEY CONTROL CHARACTERISTICS –

Part 6-18: Graphene-based material – Functional groups: TGA-FTIR

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC TS 62607-6-18 has been prepared by IEC technical committee 113: Nanotechnology for
electrotechnical products and systems. It is a Technical Specification.
The text of this Technical Specification is based on the following documents:
Draft Report on voting
113/680/DTS 113/706/RVDTS
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.

– 4 – IEC TS 62607-6-18:2022  IEC 2022
A list of all parts in the IEC TS 62607 series, published under the general title
Nanomanufacturing – Key control characteristics, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.

INTRODUCTION
One of the most well-studied routes for the preparation of graphene is the oxidation and
reduction process. The most cost-effective process to obtain graphene is the exfoliation of
natural graphite layers after oxidation to get individual oxidized layers and then de-oxygenation
(reduction) of these individual layers [1], [2] . During the oxidation process, various
functionalized groups (-OH, -O-, -COOH, C=O, etc.) go into the graphene skeleton, breaking
the π bond of graphene structure [3]. Oxygen attachment to graphene in any chemical form
(epoxide, hydroxyl, carboxyl and ketonic-type functional groups) both on the basal plane and at
the edges reduces electronic states at the Fermi level [4], [5], [6]. The type and content of
functional groups affect the physiochemical properties of graphene. Therefore, the identification
and quantification of functional groups on graphene powder is believed to be a key control
characteristic for its production and application.
Coupling thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR)
is an excellent solution to identify and quantify functional groups on graphene powder. In TGA-
FTIR, while mass changes such as sample pyrolysis and vaporization that accompany changes
in temperature are measured quantitatively by the TGA, qualitative analysis of the gaseous
components can be conducted simultaneously by FTIR measurement of the obtained spectra.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.