IEC 60204-1:1997/COR1:1998
(Corrigendum)Corrigendum 1 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements
Corrigendum 1 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements
Corrigendum 1 - Sécurité des machines - Equipement électrique des machines - Partie 1: Règles générales
General Information
Relations
Standards Content (Sample)
Publication 60204-1 de la CEI IEC Publication 60204-1
(Quatrième édition – 1997) (Fourth edition – 1997)
Sécurité des machines – Safety of machinery –
Equipement électrique des machines – Electrical equipment of machines –
Partie 1: Règles générales Part 1: General requirements
CORRIGENDUM 1
2 Références normatives 2 Normative references
Page 24 Page 25
Remplacer la quatrième référence Replace the fourth reference
CEI 60364-6-61:1986, Installations IEC 60364-6-61:1986, Electrical installations of
électriques des bâtiments –
...
This May Also Interest You
- Standard21 pagesEnglish and French languagesale 15% off
IEC 62061:2021 specifies requirements and makes recommendations for the design, integration and validation of safety-related control systems (SCS) for machines. It is applicable to control systems used, either singly or in combination, to carry out safety functions on machines that are not portable by hand while working, including a group of machines working together in a coordinated manner.
This document is a machinery sector specific standard within the framework of IEC 61508 (all parts).
The design of complex programmable electronic subsystems or subsystem elements is not within the scope of this document.
The main body of this sector standard specifies general requirements for the design, and verification of a safety-related control system intended to be used in high/continuous demand mode.
This document:
– is concerned only with functional safety requirements intended to reduce the risk of hazardous situations;
– is restricted to risks arising directly from the hazards of the machine itself or from a group of machines working together in a coordinated manner;
This document does not cover
– electrical hazards arising from the electrical control equipment itself (e.g. electric shock - see IEC 60204-1);
– other safety requirements necessary at the machine level such as safeguarding;
– specific measures for security aspects – see IEC TR 63074.
This document is not intended to limit or inhibit technological advancement.
IEC 62061:2021 cancels and replaces the first edition, published in 2005, Amendment 1:2012 and Amendment 2:2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
– structure has been changed and contents have been updated to reflect the design process of the safety function,
– standard extended to non-electrical technologies,
– definitions updated to be aligned with IEC 61508-4,
– functional safety plan introduced and configuration management updated (Clause 4),
– requirements on parametrization expanded (Clause 6),
– reference to requirements on security added (Subclause 6.8),
– requirements on periodic testing added (Subclause 6.9),
– various improvements and clarification on architectures and reliability calculations (Clause 6 and Clause 7),
– shift from "SILCL" to "maximum SIL" of a subsystem (Clause 7),
– use cases for software described including requirements (Clause 8),
– requirements on independence for software verification (Clause 8) and validation activities (Clause 9) added,
– new informative annex with examples (Annex G),
– new informative annexes on typical MTTFD values, diagnostics and calculation methods for the architectures (Annex C, Annex D and Annex H).
- Standard289 pagesEnglish languagesale 15% off
- Standard304 pagesEnglish and French languagesale 15% off
IEC 60204-32:2023 applies to electrical, electronic, programmable electronic equipment and systems to hoisting machines and related equipment, including a group of hoisting machines working together in a co-ordinated manner. The equipment covered by this document commences at the point of connection of the supply to the electrical equipment of the hoisting machine (crane-supply-switch) and includes systems for power supply and control feeders situated outside of the hoisting machine, for example, flexible cables or conductor wires or conductor bars. This document is applicable to equipment or parts of equipment not exceeding 1 000 V AC or 1 500 V DC between lines and with nominal frequencies not exceeding 200 Hz. This document does not cover all the requirements (for example guarding, interlocking, or control) that are needed or required by other standards or regulations in order to protect persons from hazards other than electrical hazards. Each type of hoisting machine has unique requirements to be accommodated to provide adequate safety. This document does not cover noise risks. Additional and special requirements can apply to the electrical equipment of hoisting machines including those that
– handle or transport potentially explosive material (e.g. paint or sawdust);
– are intended for use in potentially explosive and/or flammable atmospheres;
– have special risks when transporting or moving certain materials;
– are intended for use in mines.
For the purposes of this document, hoisting machines include cranes of all types, winches of all types and storage and retrieval machines. The following product groups are included:
– overhead travelling cranes;
– mobile cranes;
– tower cranes;
– slewing luffing cranes;
– gantry cranes;
– offshore cranes;
– floating cranes;
– winches of all types;
– hoists and accessories;
– loader cranes;
– cable cranes;
– load holding devices;
– storage and retrieval machines;
– monorail hoists;
– straddle carriers;
– rubber tyred gantry cranes (RTGs).
This document does not cover individual items of electrical equipment other than their selection for use and their erection.
IEC 60204-32:2023 cancels and replaces the second edition published in 2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment to the IEC 60204-1 sixth edition (2016) especially for:
– requirements for earthing and bonding;
– requirements for circuit protection;
– consideration of use of Power Drive Systems;
– protective bonding requirements and terminology;
– requirements pertaining to safe torque off for PDS, emergency stop, and control circuit protection;
– symbols for actuators of control devices;
b) reference for high voltage electrical equipment;
c) cableless control system requirements;
d) EMC requirements;
e) technical documentation requirements;
f) general updating to current special national conditions, normative standards, and bibliographical references.
- Standard496 pagesEnglish languagesale 15% off
- Standard313 pagesEnglish and French languagesale 15% off
IEC TS 63394:2023 In the context of the safety of machinery, the sector standard IEC 62061, along with ISO 13849 1, provides requirements to manufacturers of machines for the design, development and integration of safety-related control systems (SCS) or safety-related parts of control systems (SRP/CS), depending on technology used (mechanical, pneumatic, hydraulic or electrical technologies) to perform safety function(s). This document does not replace ISO 13849-1 and IEC 62061. This document gives additional guidance to the application of IEC 62061 or ISO 13849-1.
This document:
– gives guidelines and specifies additional requirements for specific safety functions based on the methodology of ISO 12100, which are relevant in machinery and respecting typical boundary conditions of machinery;
– considers safety functions which are designed for high demand mode of operation yet are rarely operated, called rarely activated safety functions;
– gives additional information for the calculation of failure rates using other (non-electronic) technologies based e.g. on Weibull distribution, because all the formula defined in IEC 62061 and ISO 13849-1 are based on exponential distribution.
Therefore, the basis for these guidelines and additional requirements is
– a typical classification of safety functions;
– a consideration of typical architectures used for designing safety functions;
– a consideration of modes of operation of safety functions;
– the derivation and evaluation of PFH formulas for subsystems considering the used technology.
This document does not address low demand mode of operation according to IEC 61508.
This document does not take into account either layer of protection analysis (LOPA) or basic process control system (BPCS), according to IEC 61511 as a risk reduction measure.
This document considers all lifecycle phases of the machine regarding functional safety, and SCS or SRP/CS.
- Technical specification142 pagesEnglish languagesale 15% off
IEC TS 63074:2023 identifies the relevant aspects of the IEC 62443 series related to security threats and vulnerabilities that are considered for the design and implementation of safety-related control systems (SCS) which can lead to the loss of the ability to maintain safe operation of a machine.
Typical security aspects related to the machine with potential relation to SCS are:
– vulnerabilities of the SCS either directly or indirectly through the other parts of the machine which can be exploited by security threats that can result in security attacks (security breach);
– influence on the safety characteristics and ability of the SCS to properly perform its function(s);
– typical use case definition and application of a corresponding threat model.
Non-safety-related aspects of security threats and vulnerabilities are not considered in this document.
The focus of this document is on intentional malicious actions. However, intentional hardware manipulation (e.g. wiring, exchange of components) or foreseeable misuse by physical manipulation of SCS (e.g. physical bypass) is not considered in this document.
This document does not cover security requirements for information technology (IT) products and for the design of devices used in the SCS (e.g., product specific standards can be available, such as IEC TS 63208).
- Technical specification30 pagesEnglish languagesale 15% off
- Standard20 pagesEnglish and French languagesale 15% off
IEC 60204-11:2018 is now available as IEC 60204-11:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60204-11:2018 applies to electrical and electronic equipment and systems to machines, including a group of machines working together in a co-ordinated manner, which operate at nominal voltages above 1 000 V AC or 1 500 V DC and not exceeding 36 kV AC or DC with nominal frequencies not exceeding 60 Hz. IEC 60204-11:2018 cancels and replaces the first edition, published in 2000. This edition constitutes a technical revision. This edition contains significant technical changes with respect to the previous edition regarding the following:
– aspects of risk assessment, which are mirrored from ISO 12100;
– equipotential bonding and earthing;
– EMC and power quality;
– HV switchgear and controlgear;
– creepage distances for conductors and slip-ring assemblies;
– a list of machinery using HV equipment, in Annex A.
IEC 60204-11:2018 has been updated and improved to reflect the experience gained with the first edition and the evolution of high-voltage equipment reflected in the relevant standards. Regarding formal requirements, IEC 60204-11 has been aligned with
– IEC 60204-1:2016,
– IEC 61936-1:2010 and IEC 61936-1:2010/AMD1:2014,
– IEC 62271 (all parts). This document is intended to be used in conjunction with IEC 60204-1.
- Standard191 pagesEnglish languagesale 15% off
- Standard120 pagesEnglish and French languagesale 15% off
IEC 62745:2017 specifies requirements for the functionality and interfacing of cableless (for example, radio, infra-red) control systems that provide communication between operator control station(s) and the control system of a machine. Specific requirements are included for such operator control stations that are portable by the operator.
- Standard27 pagesEnglish languagesale 15% off
- Standard55 pagesEnglish and French languagesale 15% off
IEC 60204-1:2016 is available as IEC 60204-1:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60204-1:2016 applies to electrical, electronic and programmable electronic equipment and systems to machines not portable by hand while working, including a group of machines working together in a co-ordinated manner. The equipment covered by this part of IEC 60204 commences at the point of connection of the supply to the electrical equipment of the machine. This sixth edition cancels and replaces the fifth edition published in 2005. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- added requirements to address applications involving power drive systems (PDS);
- revised electromagnetic compatibility (EMC) requirements;
- clarified overcurrent protection requirements;
- requirements for determination of the short circuit current rating of the electrical equipment;
- revised protective bonding requirements and terminology;
- reorganization and revision to Clause 9, including requirements pertaining to safe torque off of PDS, emergency stop, and control circuit protection;
- revised symbols for actuators of control devices;
- revised technical documentation requirements;
- general updating to current special national conditions, normative standards, and bibliographical references.
- Standard439 pagesEnglish languagesale 15% off
- Standard277 pagesEnglish and French languagesale 15% off
- Standard563 pagesEnglish and French languagesale 15% off
specifies requirements and makes recommendations for the design, integration and validation of safety-related electrical, electronic and programmable electronic control systems (SRECS) for machines (see Notes 1 and 2). It is applicable to control systems used, either singly or in combination, to carry out safety-related control functions on machines that are not portable by hand while working, including a group of machines working together in a co-ordinated manner. The contents of the corrigenda of July 2005 and April 2008 have been included in this copy.
- Standard10 pagesEnglish and French languagesale 15% off
- Standard205 pagesEnglish and French languagesale 15% off
- Standard204 pagesEnglish and French languagesale 15% off
- Standard387 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.