EN IEC 62677-3-102:2018

SLOVENSKI STANDARD
01-junij-2018
7RSORWQRVNUþOMLYHEUL]JDQHIRUPH]DXSRUDERSULQL]NLLQVUHGQMLQDSHWRVWLGHO
6SHFLILNDFLMD]DSRVDPH]QHPDWHULDOHOLVW7RSORWQRVNUþOMLYHSROLROHILQVNH
EUL]JDQHIRUPHRGSRUQHSURWLSOD]HþLPWRNRP]DXSRUDERQDVUHGQMLK
QDSHWRVWQLK,(&
Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for
individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded
shapes for medium voltage applications (IEC 62677-3-102:2018)
Ta slovenski standard je istoveten z: EN IEC 62677-3-102:2018
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62677-3-102

NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 29.035.20; 29.035.01
English Version
Heat-shrinkable low and medium voltage moulded shapes - Part
3: Specification for individual materials - Sheet 102: Heat-
shrinkable, polyolefin, anti-tracking moulded shapes for medium
voltage applications
(IEC 62677-3-102:2018)
Profilés thermorétractables basse et moyenne tensions - Wärmeschrumpfende Nieder- und Mittelspannungsformteile
Partie 3: Spécification pour matériaux particuliers - Feuille - Teil 3: Materialanforderungen - Blatt 102:
102: Profilés thermorétractables anticheminement en Wärmeschrumpfende Formteile aus Polyolefin,
polyoléfine pour applications moyenne tension kriechstromfest, für Mittelspannungsanwendungen
(IEC 62677-3-102:2018) (IEC 62677-3-102:2018)
This European Standard was approved by CENELEC on 2018-02-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62677-3-102:2018 E

European foreword
The text of document 15/815/FDIS, future edition 1 of IEC 62677-3-102, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62677-3-102:2018.

The following dates are fixed:
• latest date by which the document has to be (dop) 2018-11-14
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-02-14
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62677-3-102:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60684-3-280:2010 NOTE Harmonized as EN 60684-3-280:2010 (not modified).
IEC 60684-3- NOTE Harmonized as EN 60684-3-280:2010/A1:2014 (not modified).
280:2010/A1:2013
IEC 60684-3-283:2010 NOTE Harmonized as EN 60684-3-283:2011 (not modified).
IEC 60684-3- NOTE Harmonized as EN 60684-3-283:2011/A1:2014 (not modified).
283:2010/A1:2013
ISO 846:1997 NOTE Harmonized as EN ISO 846:1997 (not modified).

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60296 -  Fluids for electrotechnical applications - EN 60296 -
Unused mineral insulating oils for
transformers and switchgear
IEC 60757 -  Code for designation of colours HD 457 S1 -
IEC 62677-1 -  Heat shrinkable low and medium voltage EN IEC 62677-1 -
moulded shapes -- Part 1: General
requirements
IEC 62677-2 -  Heat shrinkable low and medium voltage EN IEC 62677-2 -
moulded shapes -- Part 2: Methods of test

IEC 62677-3-102 ®
Edition 1.0 2018-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Heat-shrinkable low and medium voltage moulded shapes –

Part 3: Specification for individual materials – Sheet 102: Heat-shrinkable,

polyolefin, anti-tracking moulded shapes for medium voltage applications

Profilés thermorétractables basse et moyenne tensions –

Partie 3: Spécification pour matériaux particuliers – Feuille 102: Profilés

thermorétractables anticheminement en polyoléfine pour applications moyenne

tension
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.035.20 29.035.01 ISBN 978-2-8322-5226-0

– 2 – IEC 62677-3-102:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Designation . 7
5 Conditions of test for dimensions . 7
6 Requirements . 7
7 Moulded shapes material conformance . 7
Annex A (informative) Adhesive compatibility guide . 10
Bibliography . 11

Table 1 – Property requirements . 8
Table 2 – Resistance to selected fluids . 9
Table A.1 – Adhesive compatibility guide . 10

IEC 62677-3-102:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HEAT-SHRINKABLE LOW AND MEDIUM
VOLTAGE MOULDED SHAPES –
Part 3: Specification for individual materials –
Sheet 102: Heat-shrinkable, polyolefin, anti-tracking
moulded shapes for medium voltage applications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62677-3-102 has been prepared by IEC technical committee 15:
Solid electrical insulating materials.
The text of this International Standard is based on the following documents:
FDIS Report on voting
15/815/FDIS 15/821/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC 62677-3-102:2018 © IEC 2018
A list of all parts in the IEC 62677 series, published under the general title Heat-shrinkable
low and medium voltage moulded shapes, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 62677-3-102:2018 © IEC 2018 – 5 –
INTRODUCTION
This part of IEC 62677 is one of a series that deals with heat shrinkable low and medium
voltage moulded shapes. The series consists of three parts:
Part 1: General requirements (IEC 62677-1);
Part 2: Methods of test (IEC 62677-2);
Part 3: Specification for individual materials (IEC 62677-3).
This standard gives one of the sheets comprising Part 3 as follows:
Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications
Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shap
...