EN IEC 62841-3-9:2020

SLOVENSKI STANDARD
01-september-2020
Nadomešča:
SIST EN 62841-3-9:2016
SIST EN 62841-3-9:2016/A11:2018
SIST EN 62841-3-9:2016/AC:2016
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
9. del: Posebne zahteve za prenosne zajeralne žage (IEC 62841-3-9:2020)
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-9: Particular requirements for transportable mitre saws (IEC
62841-3-9:2020)
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 3-9: Besondere Anforderungen für
transportable Gehrungskappsägen (IEC 62841-3-9:2020)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-9: Exigences particulières pour les scies à onglets transportables (IEC
62841-3-9:2020)
Ta slovenski standard je istoveten z: EN IEC 62841-3-9:2020
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62841-3-9

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS 25.140.20 Supersedes EN 62841-3-9:2015 and all of its
amendments and corrigenda (if any)
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-9: Particular
requirements for transportable mitre saws
(IEC 62841-3-9:2020)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-9: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à onglets transportables Gartenmaschinen - Sicherheit - Teil 3-9: Besondere
(IEC 62841-3-9:2020) Anforderungen für transportable Gehrungskappsägen
(IEC 62841-3-9:2020)
This European Standard was approved by CENELEC on 2020-03-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62841-3-9:2020 E

European foreword
The text of document 116/430/FDIS, future edition 2 of IEC 62841-3-9, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-3-9:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-20
document have to be withdrawn
This document supersedes EN 62841-3-9:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of
Endorsement notice
The text of the International Standard IEC 62841-3-9:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 62841-3-10 NOTE Harmonized as EN 62841-3-10

IEC 62841-3-9 ®
Edition 2.0 2020-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Electric motor-operated hand-held tools, transportable tools and lawn

and garden machinery – Safety –

Part 3-9: Particular requirements for transportable mitre saws

Outils électroportatifs a moteur, outils portables et machines pour jardins

et pelouses – Sécurité –
Partie 3-9: Exigences particulières pour les scies à onglets transportables

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-7801-7

– 2 – IEC 62841-3-9:2020 © IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 11
5 General conditions for the tests . 11
6 Radiation, toxicity and similar hazards . 11
7 Classification . 11
8 Marking and instructions . 11
9 Protection against access to live parts . 14
10 Starting . 14
11 Input and current . 14
12 Heating . 15
13 Resistance to heat and fire . 15
14 Moisture resistance . 15
15 Resistance to rusting . 15
16 Overload protection of transformers and associated circuits . 15
17 Endurance . 15
18 Abnormal operation . 15
19 Mechanical hazards . 16
20 Mechanical strength . 22
21 Construction . 24
22 Internal wiring . 31
23 Components . 31
24 Supply connection and external flexible cords . 31
25 Terminals for external conductors . 32
26 Provision for earthing . 32
27 Screws and connections . 32
28 Creepage distances, clearances and distances through insulation . 32
Annexes . 33
Annex I (informative) Measurement of noise and vibration emissions . 33
Annex K (normative) Battery tools and battery packs . 34
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 35
Bibliography . 36

Figure 101 – Mitre saw with centre workpiece support . 7
Figure 102 – Mitre saw . 9
Figure 103 – Saw blade quadrants . 10
Figure 104 – Open guard construction . 18
Figure 105 – Position of saw blade and lower guard relative to saw table . 19

IEC 62841-3-9:2020 © IEC 2020 – 3 –
Figure 106 – Test probe . 20
Figure 107 – Application of test probe . 20
Figure 108 – Workpiece support dimensions . 26
Figure 109 – Minimum extension of fence . 28
Figure 110 – Distance between fence and saw blade . 29
Figure 111 – Flange characteristics . 31

Table 4 – Required performance levels . 15
Table I.101 – Noise test conditions for mitre saws . 33

– 4 – IEC 62841-3-9:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS,
TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-9: Particular requirements for transportable mitre saws

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in th
...