iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60060-2:1994/A11:1998

(Amendment)

High-voltage test techniques - Part 2: Measuring systems

High-voltage test techniques - Part 2: Measuring systems

Superseded by EN 60060-2:2011

Hochspannungs-Prüftechnik - Teil 2: Meßsysteme

Techniques des essais à haute tension - Partie 2: Systèmes de mesure

High-voltage test techniques - Part 2: Measuring systems - Amendment 1

General Information

Status
Withdrawn
Publication Date
12-Jan-1998
Withdrawal Date
31-Jul-1998
ICS
19.080 - Electrical and electronic testing
Technical Committee
CLC/SR 42 - High-voltage testing techniques
Drafting Committee
IEC/TC 42 - IEC_TC_42
Parallel Committee
IEC/TC 42 - IEC_TC_42
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Jan-2014
Completion Date
01-Jan-2014
Ref Project
SIST EN 60060-2:1998/A11:2000 - High-voltage test techniques - Part 2: Measuring systems - Amendment 1

Relations

Replaced By
EN 60060-2:2011 - High-voltage test techniques - Part 2: Measuring systems
Effective Date
28-Jan-2023
Amends
EN 60060-2:1994 - High-voltage test techniques - Part 2: Measuring systems
Effective Date
28-Jan-2023

Buy Standard

EN 60060-2:1998/A11:2000EN 60060-2:1998/A11:2000
PreviousNext
Amendment
EN 60060-2:1998/A11:2000
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2000
High-voltage test techniques - Part 2: Measuring systems - Amendment 1
High-voltage test techniques - Part 2: Measuring systems - Amendment 1
Hochspannungs-Prüftechnik -- Teil 2: Meßsysteme
Techniques des essais à haute tension -- Partie 2: Systèmes de mesure
Ta slovenski standard je istoveten z: EN 60060-2:1994/A11:1998
ICS:
19.080 (OHNWULþQRLQHOHNWURQVNR Electrical and electronic
SUHVNXãDQMH testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61083-3:2021(Main)
Instruments and software used for measurement in high-voltage and high-current tests - Part 3: Requirements for hardware for tests with alternating and direct voltages and currents
SIST EN IEC 61083-3:2021

IEC 61083-3:2020 is applicable to digital recording instruments used for measurements during tests with high alternating and direct voltages and currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertainties and procedures specified in the relevant IEC standards (e.g. IEC 60060-1, IEC 60060-2, IEC 60060-3, IEC 62475, IEC 61180). This document is applicable to those digital recording instruments that will be designed and type tested according to this document. This document • defines performance requirements for digital recording instruments used during tests with alternating voltages and currents (AC) or direct voltages and currents (DC); • specifies the necessary requirements for such instruments to ensure their suitability for use under the relevant standards; • establishes the tests and procedures necessary to demonstrate their compliance; • defines the terms related to digital recording instruments with recording function and access to raw data. Examples of relevant alternating and direct voltages and currents to be measured are listed in Annex D. This International Standard has the status of a horizontal standard in accordance with IEC Guide 108.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61180:2016(Main)
High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment
SIST EN 61180:2017

IEC 61180:2016 is applicable to dielectric tests with direct voltage; dielectric tests with alternating voltage; dielectric tests with impulse voltage and test equipment used for dielectric tests on low-voltage equipment. This standard is applicable only to tests on equipment having a rated voltage of not more than 1 kV a.c. or 1,5 kV d.c. This standard is applicable to type and routine tests for objects which are subjected to high voltage tests as specified by the technical committee. The test equipment comprises a voltage generator and a measuring system. This standard covers test equipment in which the measuring system is protected against external interference and coupling by appropriate screening, for example a continuous conducting shield. Therefore, simple comparison tests are sufficient to ensure valid results. This standard is not intended to be used for electromagnetic compatibility tests on electric or electronic equipment. Tests with the combination of impulse voltages and currents are covered by IEC 61000-4-5. This standard provides the relevant technical committees as far as possible with: - defined terms of both general and specific applicability; - general requirements regarding test objects and test procedures; - methods for generation and measurement of test voltages; - test procedures; - methods for the evaluation of test results and to indicate criteria for acceptance; - requirements concerning approved measuring devices and checking methods and measurement uncertainty. Alternative test procedures may be required and these should be specified by the relevant technical committees. Care should be taken if the test object has voltage limiting devices, as they may influence the results of the test. The relevant technical committees should provide guidance for testing objects equipped with voltage limiting devices. This 1st edition of IEC 61180 cancels and replaces the 1st edition of IEC 61180-1, issued in 1992, and the 1st edition of IEC 61180-2, issued in 1994. Key words: High Voltage Test Techniques, Dielectric Tests, Disruptive Discharge, Withstand Voltage.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60270:2001/A1:2016(Amendment)
High-voltage test techniques - Partial discharge measurements
SIST EN 60270:2002/A1:2016

Applicable to the measurement of partial discharges which occur in electrical apparatus, components or systems when tested with alternating voltage up to 400 Hz or with direct voltage.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61083-2:2013(Main)
Instruments and software used for measurement in high-voltage and high-current tests - Part 2: Requirements for software for tests with impulse voltages and currents
SIST EN 61083-2:2013

IEC 61083-2:2013 applies to software used for evaluation of impulse parameters from recorded impulse voltages and currents. It provides test waveforms and reference values for the software required to meet the measuring uncertainties and procedures specified in IEC 60060-1, IEC 60060-2, IEC 60060-3 and IEC 62475. Hardware with built-in firmware that cannot accept external numerical input data is not covered by this standard. The object of this standard is to establish the tests which are necessary to show that the performance of the software complies with the requirements of the relevant IEC standards, define the terms specifically related to digital processing, specify reference values and the acceptance limits for the reference impulses, specify the requirements for the record of performance and define the methods to assess the contribution of software to the measurement uncertainty. This second edition cancels and replaces the first edition published in 1996 and constitutes a technical revision. The main changes with respect to the previous edition are: - the test data generator software has been updated, - the number of reference impulse waveforms included in the test data generator has been significantly increased, - all reference values have been recalculated according to new definitions in IEC 60060-1 and IEC 62475 and - methods for estimating the uncertainty of parameter evaluation have been introduced and are in line with the procedure introduced in IEC 60060-2. Keywords: High voltage, High current, Impulse voltage, Impulse current.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60060-2:2011(Main)
High-voltage test techniques - Part 2: Measuring systems
SIST EN 60060-2:2011

IEC 60060-2:2010 is applicable to complete measuring systems, and to their components, used for the measurement of high voltages during laboratory and factory tests with direct voltage, alternating voltage and lightning and switching impulse voltages as specified in IEC 60060-1. For measurements during on-site tests see IEC 60060-3. The limits on uncertainties of measurements stated in this standard apply to test levels stated in IEC 60071-1:2006. The principles of this standard apply also to higher levels but the uncertainty may be greater. This standard also defines the terms used, methods to estimate the uncertainties of high-voltage measurements, states the requirements which the measuring systems shall meet, describes the methods for approving a measuring system and checking its components and describes the procedures by which the user shall show that a measuring system meets the requirements of this standard, including the limits set for the uncertainty of measurement. This third edition cancels and replaces the second edition, published in 1994, and constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: - The general layout and text was updated and improved to make the standard easier to use. - The standard was revised to align it with IEC 60060-1. - The treatment of measurement uncertainty estimation has been expanded.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62475:2010(Main)
High-current test techniques - Definitions and requirements for test currents and measuring systems
SIST EN 62475:2011

IEC 62475:2010 is applicable to high-current testing and measurements on both high-voltage and low-voltage equipment. It deals with steady-state and short-time direct current (as e.g. encountered in high-power d.c. testing), steady-state and short-time alternating current (as e.g. encountered in high-power a.c. testing), and impulse-current. In general, currents above 100 A are considered in this International Standard, although currents less than this can occur in tests. This standard also covers fault detection during, for example, lightning impulse testing.

  • Standard
    106 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60060-3:2006(Main)
High voltage test techniques - Part 3: Definitions and requirements for on-site tests
SIST EN 60060-3:2006

Applicable to the following on-site test voltages and in service stresses, which are in relation to IEC 60060-1: direct voltage;alternating voltage; lightning impulse voltage of aperiodic or oscillating shape: switching impulse voltage of aperiodic or oscillating shape.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60052:2002(Main)
Voltage measurement by means of standard air gaps
SIST EN 60052:2004

Applies to the construction and use of sphere-gaps for measuring the peak value of alternating, direct and both full standard and longer tail impulse voltages. Peak values of the disruptive voltages in air are given in tabular form. Note: - For high-voltage test techniques, see EN 60.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61083-1:2001(Main)
Instruments and software used for measurement in high-voltage impulse tests - Part 1: Requirements for instruments
SIST EN 61083-1:2002

Applies to digital recorders and digital oscilloscopes used for measurements during tests with high impulse voltages and high impulse currents. Specifies the measuring characteristics and calibrations required to meet the measuring accuracies and procedures given in EN 60-1.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60270:2001(Main)
High-voltage test techniques - Partial discharge measurements
SIST EN 60270:2002

Applies to the measurement of localized electrical discharges in insulating media, restricted to only a part of the dielectric under test and only partially bridging the insulation between conductors.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day