EN 140402:2015

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Vordruck für Bauartspezifikation: Oberflächenmontierbare drahtgewickelte Festwiderstände (SMD) niedriger BelastbarkeitSpécification particulière cadre: Résistances fixes bobinées à faible dissipation pour montage en surface (CMS)Blank Detail Specification: Fixed low power wirewound surface mount (SMD) resistors31.040.10Fiksni uporFixed resistorsICS:Ta slovenski standard je istoveten z:EN 140402:2015SIST EN 140402:2015en01-junij-2015SIST EN 140402:2015SLOVENSKI
STANDARDSIST EN 140402:20021DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 140402
April 2015 ICS 31.040.10
Supersedes
EN 140402:1998
English Version
Blank Detail Specification: Fixed low power wirewound surface mount (SMD) resistors
Spécification particulière cadre: Résistances fixes bobinées à faible dissipation pour montage en surface (CMS)
Vordruck für Bauartspezifikation: Oberflächenmontierbare drahtgewickelte Festwiderstände (SMD) niedriger Belastbarkeit This European Standard was approved by CENELEC on 2014-12-15. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 140402:2015 E SIST EN 140402:2015

Contents Foreword . 4 Introduction . 5 1 Characteristics and ratings . 7 1.1 General . 7 1.2 Dimensions and ratings . 7 1.3 Derating curve . 8 1.4 Resistance range and tolerance on rated resistance . 8 1.4.1 Level P . 8 1.4.2 Level R . 9 1.5 Variation of resistance with temperature and temperature rise . 10 1.6 Climatic categories . 11 1.7 Limits for change of resistance at tests . 11 1.8 Non-linearity . 13 1.9 Tests related to soldering . 13 1.9.1 Severities for solderability testing . 13 1.9.2 Severities for testing resistance to soldering heat . 13 1.10 Marking, packaging and ordering designation . 13 1.10.1 Marking of the component . 13 1.10.2 Packaging . 13 1.10.3 Marking of the packaging . 13 1.10.4 Ordering information . 13 1.11 Additional information (not for inspection purpose) . 14 1.11.1 Storage . 14 1.11.2 Mounting . 14 1.11.3 Soldering process . 14 1.11.4 Conductive gluing . 15 1.11.5 Use of cleaning solvents . 15 1.11.6 Pulse load capability . 15 1.11.7 Variation of resistance (drift) for lifetimes up to 200 000 h. 15 1.11.8 Dissipation notes . 15 2 Quality assessment procedures . 15 2.1 General . 15 2.1.1 Zero defect approach . 15 2.1.2 100 % Test . 16 2.1.3 Certificate of Conformity (CoC) . 16 2.1.4 Certified test records . 16 2.1.5 Failure rate level . 16 2.2 Qualification approval . 17 2.2.1 General . 17 2.2.2 Level P . 17 2.2.3 Level R . 17 2.3 Quality conformance inspection . 17 2.3.1 General . 17 2.3.2 Qualification approval according to QC 001002-3:2005, Clause 3 . 17 2.3.3 Technology approval according to QC 001002-3:2005, Clause 6 . 17 2.3.4 Non-conforming items . 18 SIST EN 140402:2015

- 3 - EN 140402:2015 Annex A (normative)
Fixed sample size Qualification Approval and Quality Conformance Inspection test schedule for fixed low power wire wound SMD resistors . 19 Annex B (informative)
Letter symbols and abbreviations . 29 B.1 Letter symbols . 29 B.2 Abbreviations . 30 Annex C (normative)
Normative references . 31 Bibliography . 32
Foreword This document (EN 140402:2015) has been prepared by CLC/TC 40XB, "Resistors".
The following dates are fixed:
• latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-12-15 • latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2017-12-15
This document supersedes EN 140402:1998.
- 5 - EN 140402:2015 Introduction Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements should not be considered as being in accordance with European Standards nor should they be so described. In the preparation of the detail specification the content of EN 60115-8:2012, 1.4 should be taken into account. The detail specification should be written by using the preferred values given in EN 60115-8. The detail specification should contain a table of contents prior the first page of the actual specification. For the use of SI units refer to EN ISO 80000-1, for the use of letter symbols to be used in electrical technology, refer to EN 60027-1. This Blank Detail Specification uses two different kinds of notes: – NOTE
for notes which give additional information intended to assist the understanding or use of the resulting document and therefore should be copied as NOTE into the drafted Detail Specification. – NOTE (ed)
for editorial notes which are intended to aid and direct the specification writer and therefore should not be copied into the drafted Detail Specification. Identification of the detail specification and the component The first page of the detail specification should have the layout recommended on page 6. The numbers in square brackets correspond to the indications to be completed thereunder: [1] the name of the Standardisation Organisation under whose authority the detail specification is published and if applicable, the organisation from whom the detail specification is available; [2] the CECC symbol and the number allocated to the detail specification by the CENELEC General Secretariat; [3] the number and issue number of the EN generic and sectional specification as relevant; also national reference if different; [4] the national number of the detail specification, date of issue and any further information required by the national system, together with any amendment numbers, if different from the EN number; [5] a brief description of the component or range of components; [6] information on typical construction (where applicable); [7] an outline drawing with the main dimensions which are of importance for interchangeability and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an annex to the detail specification; [8] the level of quality assessment covered by the detail specification. For [5] and [6] the text to be given in the detail specification should be suitable for an entry in a register of approvals and the “CENELEC Catalogue of European Standards”. SIST EN 140402:2015

Specification available from: [1]
EN 140402- . . . (Specification number)
[2]
Electronic components of assessed quality in accordance with: [3] EN 60115-1:2011 EN 60115-8:2012 EN 140402:2015 Issue . . .
[4] April 2015
[7]
Other shapes are permitted within the given dimensions. Figure 1 — Outline and dimensions (see Table 1) Fixed low power wire wound
[5] resistors
[6] (Description of the component)
Assessment level EZ a [8] Level P: with 100 %-test Level R: with failure rate level
and 100 %-test S
...