iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61264:1998

(Main)

Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear

Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear

Applies to hollow insulators made of ceramic material, with their fixing devices, intended for use with a permanent gas pressure greater than 50 kPa gauge having an internal volume equal to or greater than 1 l (1 000 cm3). They are intended for use in electrical equipment operating on alternating current with a rated voltage greater than 1000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a rated voltage greater than 1 500 V.

Druckbeanspruchte Hohlisolatoren aus keramischem Werkstoff für Hochspannungs- Schaltgeräte und Schaltanlagen

Enveloppes isolantes sous pression en matière céramique pour l'appareillage haute tension

S'applique aux isolateurs en matière céramique creux, avec leurs dispositifs de fixation, destinés à être utilisés avec une pression de gaz permanente supérieure à 50 kPa et ayant un volume interne égal ou supérieur à 1 l (1 000 cm3). Ils sont destinés à être utilisés dans des appareils électriques fontionnant en courant alternatif avec une tension nominale supérieure à 1 000 V et une fréquence de 100 Hz au maximum, ou dans des appareils à courant continu avec une tension nominale supérieure à 1 500 V.

Ceramic pressurized insulators for high-voltage swichgear and controlgear (IEC 61264:1998)

General Information

Status
Withdrawn
Publication Date
05-Nov-1998
ICS
29.080.10 - Insulators
Technical Committee
CLC/SR 36C - Insulators for substations
Drafting Committee
IEC/SC 36C - IEC_SC_36C
Parallel Committee
IEC/SC 36C - IEC_SC_36C
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-May-2006
Completion Date
01-May-2006
Ref Project
SIST EN 61264:2000 - Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear

Relations

Replaces
EN 50062:1991 - Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear
Effective Date
29-Jan-2023
Replaced By
EN 62155:2003 - Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V
Effective Date
28-Jan-2023

Buy Standard

EN 61264:2000EN 61264:2000
PreviousNext
Standard
EN 61264:2000
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61264:2000
01-februar-2000
1DGRPHãþD
SIST EN 50062:1995
Ceramic pressurized insulators for high-voltage swichgear and controlgear (IEC
61264:1998)
Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear
Druckbeanspruchte Hohlisolatoren aus keramischem Werkstoff für Hochspannungs-
Schaltgeräte und Schaltanlagen
Enveloppes isolantes sous pression en matière céramique pour l'appareillage haute
tension
Ta slovenski standard je istoveten z: EN 61264:1998
ICS:
29.080.10 Izolatorji Insulators
SIST EN 61264:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61264:2000

---------------------- Page: 2 ----------------------

SIST EN 61264:2000

---------------------- Page: 3 ----------------------

SIST EN 61264:2000

---------------------- Page: 4 ----------------------

SIST EN 61264:2000

---------------------- Page: 5 ----------------------

SIST EN 61264:2000

---------------------- Page: 6 ----------------------

SIST EN 61264:2000

---------------------- Page: 7 ----------------------

SIST EN 61264:2000

---------------------- Page: 8 ----------------------

SIST EN 61264:2000

---------------------- Page: 9 ----------------------

SIST EN 61264:2000

---------------------- Page: 10 ----------------------

SIST EN 61264:2000

------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60433:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic insulators for AC systems - Characteristics of insulator units of the long rod type
SIST EN IEC 60433:2021

IEC 60433:2021 is applicable to string insulator units of the long rod type with insulating parts of ceramic material intended for use in AC overhead power lines with a nominal voltage greater than 1000 V and a frequency not greater than 100 Hz. It is also applicable to insulators of similar design, used in substations. This document is applicable to ceramic string insulator units of the long rod type, either with a clevis end fitting at both ends for coupling with a tongue, or with a socket end fitting at both ends for coupling with a pin ball. The object of this document is to prescribe specified values for electrical and mechanical characteristics, and for the principal dimensions of ceramic string insulator units of the long rod type. This fourth edition cancels and replaces the third edition published in 1998. This edition includes the following significant technical changes with respect to the previous edition: - wording in Scope changed from "should" to "are intended to"; - new normative references added; - title of Clause 4 amended, new Note 4 added; - Table 1 expanded to include more specified mechanical failing loads.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60305:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic or glass insulator units for AC systems - Characteristics of insulator units of the cap and pin type
SIST EN IEC 60305:2021

IEC 60305:2021 applies to string insulator units of the cap and pin type with insulating parts of ceramic material or glass, intended for AC overhead lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to insulators of similar design used in substations. This document applies to string insulator units of the cap and pin type either with ball and socket couplings or with clevis and tongue couplings. This document applies to string insulator units for use on overhead lines in clean areas and polluted areas. For use in areas characterized by very heavy pollution levels and for other particular or extreme environmental conditions, it may be necessary for certain dimensions to be changed and insulator units having different creepage distances, spacing and forms may be preferred (for example, flat profile, hemispherical etc.). Insulators for use on DC systems may also need different dimensions. In any case, it is applicable that the standardized mechanical characteristics of this document and coupling sizes are retained. This fifth edition cancels and replaces the fourth edition published in 1995. This edition includes the following significant technical changes with respect to the previous edition: - wording in Scope changed from "it is recommended" to "it is applicable"; - new normative references added; - electromechanical or mechanical failing load in Clause 4 specified; - new figures added showing profiles.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60372:2020(Main)
Locking devices for ball and socket couplings of string insulator units - Dimensions and tests
SIST EN IEC 60372:2020

IEC 60372:2020 is applicable to locking devices used with ball and socket couplings of string insulator units and used with the corresponding metal fittings standardized in IEC 60120, when they are supplied separately.The object of this document is - to define the shapes and some standard dimensions for locking devices, - to define the test methods for locking devices, - to state the acceptance conditions for supply, - to give other dimensions for guidance of manufacturing only. This fourth edition cancels and replaces the third edition published in 1984. This edition includes the following significant technical changes with respect to the previous edition: a. Two new designated size of couplings, 36 and 40, were introduced; b. the relevant content of the 28B W-clip was deleted; c. Annex A is informative, Annex B is normative, Annex C is informative.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60120:2020(Main)
Ball and socket couplings of string insulator units - Dimensions
SIST EN IEC 60120:2020

IEC 60120:2020 define the dimensions of a series of standard ball and socket couplings using the standard locking devices (see IEC 60372) in order to permit the assembly of insulators or metal fittings supplied by different manufacturers. This document applies to string insulator units of the cap and pin and long rod types and their associated metal fittings. For the pin ball and the socket, dimensions apply to the finished product after any surface treatment. Extreme positions of the pin ball in the socket are given in annex. Typical examples of gauges for checking the dimensions of pin balls and sockets are given in REF _Ref22908296 \r \hannex.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60471:2020(Main)
Clevis and tongue couplings of string insulator units - Dimensions
SIST EN IEC 60471:2020

IEC 60471:2020 applies to string insulator units of the cap and pin type and also of the long rod type as well as the fittings used with such insulators. The object of this document is to define the dimensions of a series of clevis and tongue couplings to permit the assembly of insulators or fittings supplied by different manufacturers. This third edition cancels and replaces the second edition published in 1977. This edition includes the following significant technical changes with respect to the previous edition: - there are no new clevis and tongue couplings; - For the dimensions of the existing designated size of couplings that characterize the same location, the effective number of the size is unified.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61952-1:2019(Main)
Insulators for overhead lines - Composite line post insulators for AC systems with a nominal voltage greater than 1 000 V - Part 1: Definitions, end fittings and designations
SIST EN IEC 61952-1:2019

This part of IEC 61952 is applicable to composite line post insulators for AC overhead lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to line post insulators of similar design used in substations or on electric traction lines. This document applies to line post insulators of composite type, generally with metallic couplings, with and without a base plate. It also applies to such insulators when used in complex structures. It does not apply to hollow insulators adapted for use as line post insulators. The object of this document is to specify the main dimensions of the couplings to be used on the composite line post insulators in order to permit the assembly of insulators or fittings supplied by different manufacturers and to allow, whenever practical, interchangeability with existing installations. It also specifies a standard designation system for composite line post insulators.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60507:2014/AC:2018-09(Corrigendum)
Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
SIST EN 60507:2014/AC:2018

IEC - Corrected version

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61466-2:1998/A2:2018(Amendment)
Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V - Part 2: Dimensional and electrical characteristics
SIST EN 61466-2:2000/A2:2018
  • Addendum – translation
    8 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62772:2016(Main)
Composite Hollow Core Station Post Insulators for substations with a.c. voltage greater than 1 000 V and d.c. voltage greater than 1 500 V - Definitions, test methods and acceptance criteria
SIST EN 62772:2017

IEC 62772:2016 applies to composite hollow core station post insulators consisting of a load-bearing insulating tube (core) made of resin impregnated fibres an insulating filler material (e.g. solid, liquid, foam, gaseous pressurized or unpressurized), a housing (outside the insulating tube) made of polymeric material (for example silicone or ethylene-propylene) and metal fixing devices at the ends of the insulating tube. Composite hollow core station post insulators as defined in this standard are intended for general use in substations in both, outdoor and indoor environments, operating with a rated AC voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current systems with a rated voltage greater than 1 500 V. The object of this standard is: - to define the terms used; - to prescribe test methods; - to prescribe acceptance criteria. All the tests in this standard, apart from the thermal-mechanical test, are performed at normal ambient temperature. This standard does not prescribe tests that may be characteristic of the apparatus of which the composite hollow core station post insulator ultimately may form a part.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61466-1:2016(Main)
Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings
SIST EN 61466-1:2016

Prescribes specified values for the mechanical characteristics of the composite string insulator units. Defines the main dimensions of the couplings to be used on the composite string insulator units in order to permit the assembly of insulators of fittings supplied by different manufacturers and to allow, whenever practical, interchangeability with existing installations. It also defines a standard designation system for composite string insulator units.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    27 pages
    French language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    25 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day