EN 62841-3-10:2015
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
IEC 62841-3-10:2015(E) applies to transportable cut-off machines intended to cut materials such as metals, concrete and masonry and to be fitted with one abrasive bonded reinforced wheel of Type 41, or diamond cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm and with a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the maximum wheel diameter and a wheel diameter range of 250 mm to 410 mm. This standard does not apply to: - transportable mitre saws; - transportable tile saws or transportable metal saws. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. This publication is to be read in conjunction with IEC 62841-1:2014. Key words: Hand-held tools, Transportable tools, Cut-off machines
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-10: Besondere Anforderungen für transportable Trennschleifmaschinen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-10: Exigences particulières pour les tronçonneuses à disque transportables
IEC 62841-3-10:2015 s’applique aux tronçonneuses à disque transportables destinées au découpage de matériaux tels que les métaux, le béton et la maçonnerie, munies d’un disque abrasif du type disque aggloméré renforcé de Type 41, ou disque à tronçonner diamant à rainures périphériques, le cas échéant, ne dépassant pas 10 mm et avec une vitesse assignée à vide ne dépassant pas une vitesse périphérique du disque de 100 m/s avec le diamètre de disque maximal et une plage de diamètres de disque compris entre 250 mm et 410 mm. La présente norme ne s’applique pas aux: scies à onglets transportables, scies à céramique transportables ou aux scies à métaux transportables. L’attention des Comités Nationaux est attirée sur le fait que les fabricants d’appareils et les organismes d’essai peuvent avoir besoin d’une période transitoire après la parution d’une nouvelle publication IEC, ou d’une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication. La présente Partie 3-10 doit être utilisée conjointement avec la première édition de l’IEC 62841-1:2014. Mots clés: outils portables, outils transportables, tronçonneuses à disque transportables Le contenu du corrigendum de juillet 2016 a été intégré dans ce texte.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-10. del: Posebne zahteve za premične rezalnike
Standard se uporablja za prenosne rezalnike za rezanje materialov, kot so kovine, beton in zidovje, na katere se namesti – ojačana abrazivna plošča tipa 41 ali – diamantna rezalna plošča z morebitnimi perifernimi luknjami, ki niso večje do 10 mm, – z nazivno hitrostjo brez obremenitve, ki ne presega periferne hitrosti plošče 100 m/s pri največjem premeru plošče in – razponom premera plošče od 250 mm do 410 mm. Ta standard se ne uporablja za: – prenosne zajeralne žage; – prenosne žage za ploščice; – prenosne žage za kovino.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2016
1DGRPHãþD
SIST EN 61029-2-10:2010
SIST EN 61029-2-10:2010/A11:2014
(OHNWURPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO 3RVHEQH]DKWHYH]DSUHPLþQHUH]DOQLNH
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
Ta slovenski standard je istoveten z: EN 62841-3-10:2015
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 62841-3-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2015
ICS 25.140.20 Supersedes EN 61029-2-10:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-10: Particular
requirements for transportable cut-off machines
(IEC 62841-3-10:2015 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-10: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à onglets transportables Gartenmaschinen - Sicherheit - Teil 3-10: Besondere
(IEC 62841-3-10:2015 , modifiée) Anforderungen für transportable Trennschleifmaschinen
(IEC 62841-3-10:2015 , modifiziert)
This European Standard was approved by CENELEC on 2015-10-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-10:2015 E
European foreword
The text of document 116/240/FDIS, future edition 1 of IEC 62841-3-10, prepared by IEC/TC 116 “Safety
of motor-operated electric tools” was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-3-10:2015.
A draft amendment, which covers common modifications to IEC 62841-3-10:2015, was prepared by
CLC/TC 116 “Safety of motor-operated electric tools” and approved by CENELEC.
The following dates are fixed:
– latest date by which this document has to be implemented (dop) 2016-10-19
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2019-10-19
with this document have to be withdrawn
This European Standard is divided into four parts:
Part 1: General requirements which are common to most electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 3-10 is to be used in conjunction with EN 62841-1:2015.
This Part 3-10 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert
it into the European Standard: Particular requirements for transportable cut-off machines.
Where a particular subclause of Part 1 is not mentioned in this Part 3-10, that subclause applies as far as
relevant. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1
is to be adapted accordingly.
Compliance with the clauses of Part 1 together with this Part 3-10 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EU Directives can be applicable to the products falling within
the scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 62841-3-10:2015 was approved by CENELEC as a
European Standard with agreed common modifications.
COMMON MODIFICATIONS
Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions
Add the following annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
This annex from EN 62841-1:2015 is applicable with the following addition:
Publication Year Title EN/HD Year
ISO 603-15 - - -
Bonded abrasive products - Dimensions -
Part 15: Grinding wheels for cutting-off on
stationary or mobile cutting-off machines
ISO 630 Series Structural steels - -
Annex ZZ
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within
the scope of this standard.
IEC 62841-3-10 ®
Edition 1.0 2015-09
INTERNATIONAL
STANDARD
colour
inside
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-10: Particular requirements for transportable cut-off machines
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.140.20 ISBN 978-2-8322-2912-5
– 2 – IEC 62841-3-10:2015 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 7
5 General conditions for the tests . 7
6 Radiation, toxicity and similar hazards . 8
7 Classification . 8
8 Marking and instructions . 8
9 Protection against access to live parts . 11
10 Starting . 11
11 Input and current . 11
12 Heating . 11
13 Resistance to heat and fire . 11
14 Moisture resistance . 11
15 Resistance to rusting . 11
16 Overload protection of transformers and associated circuits . 11
17 Endurance . 11
18 Abnormal operation . 12
19 Mechanical hazards . 12
20 Mechanical strength . 17
21 Construction . 18
22 Internal wiring . 18
23 Components . 19
24 Supply connection and external flexible cords . 19
25 Terminals for external conductors . 19
26 Provision for earthing . 19
27 Screws and connections . 19
28 Creepage distances, clearances and distances through insulation . 19
Annexes . 26
Annex I (informative) Measurement of noise and vibration emissions . 26
Annex K (normative) Battery tools and battery packs . 27
Bibliography . 28
Figure 101 – Example of a cut-off machine . 20
Figure 102 – Examples of gaps and rake angles . 21
Figure 103 – Wheel guards . 22
Figure 104 – Test probe . 22
Figure 105 – Spark deflection . 23
Figure 106 – Principal designs and dimensions of flanges . 24
Figure 107 – Position of test hole for impact test . 25
IEC 62841-3-10:2015 © IEC 2015 – 3 –
Figure 108 – Wheel guard material strength test . 25
Table 4 – Required performance levels . 12
Table 101 – Flange dimensions . 16
Table 102 – Torques for testing flanges .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.