EN 61300-2-7:2013

SLOVENSKI STANDARD
01-oktober-2013
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXVL8SRJLEQLPRPHQW
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-7: Tests - Bending moment
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-7: Prüfungen - Biegemoment
Ta slovenski standard je istoveten z: EN 61300-2-7:2013
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61300-2-7
NORME EUROPÉENNE
July 2013
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61300-2-7:1997

English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-7: Tests -
Bending moment
(IEC 61300-2-7:2013)
Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive
Procédures fondamentales d’essais et de Bauteile -
mesures - Grundlegende Prüf- und Messverfahren -
Partie 2-7: Essais - Moment de flexion Teil 2-7: Prüfungen -
(CEI 61300-2-7:2013) Biegemoment
(IEC 61300-2-7:2013)
This European Standard was approved by CENELEC on 2013-06-12. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-7:2013 E
Foreword
The text of document 86B/3579A/FDIS, future edition 2 of IEC 61300-2-7, prepared by SC 86B, “Fibre
optic interconnecting devices and passive components”, of IEC TC 86, “Fibre optics” was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-7:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2014-03-12
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-06-12
• latest date by which the national
standards conflicting with the

document have to be withdrawn
This document supersedes EN 61300-2-7:1997.
EN 61300-2-7:1997:
a) a complete reconsideration of the entire document, including additional normative references;
b) clarification of the device under test (DUT);
c) clarification of the relationship between severities, performance categories and the DUT.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61300-2-7:2013 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 61300-2-7:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation
and return loss
IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -
Part 3-4: Examinations and measurements -
Attenuation
IEC 61300-2-7 ®
Edition 2.0 2013-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-7: Tests – Bending moment

Dispositifs d'interconnexion et composants passifs à fibres optiques –

Procédures fondamentales d’essais et de mesures –

Partie 2-7: Essais – Moment de flexion

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX K
ICS 33.180.20 ISBN 978-2-83220-790-1

– 2 – 61300-2-7 © IEC:2013
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 General description . 5
4 Apparatus . 5
4.1 Design for a 1 piece or 3 piece DUT . 5
4.2 Design for a 2 piece DUT . 6
4.3 Optical measurements . 7
5 Procedure. 7
5.1 Preconditioning . 7
5.2 Initial examinations and measurements . 7
5.3 Conditioning for a 1 piece or 3 piece DUT . 7
5.4 Conditioning for a 2 piece DUT . 7
5.5 Recovery . 8
5.6 Final examinations and measurements . 8
6 Severity . 8
7 Details to be specified . 9
Annex A (informative) Example for a bending moment test method for splices . 10

Figure 1 – Test apparatus to apply a bending moment to a 1 piece or 3 piece DUT. 6
Figure 2 – Test apparatus to apply a bending moment to a 2 piece DUT . 7
Figure A.1 – Example for a bending moment test set-up for splices . 10

Table 1 – Relationship between severities, performance categories and DUT . 8
Table 2 – Severities for an 1 piece or 3 piece DUT . 9
Table 3 – Severities for an 2 piece DUT . 9

61300-2-7 © IEC:2013 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-7: Tests – Bending moment

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, se
...