EN 62442-1:2011

SLOVENSKI STANDARD
01-januar-2012
(QHUJLMVNHODVWQRVWLNUPLOQHQDSUDYHVLMDONHGHO.UPLOQDQDSUDYD]D
IOXRUHVFHQWQHVLMDONH0HULOQDPHWRGD]DXJRWDYOMDQMHFHORWQHYKRGQHPRþL
NUPLOQLKYH]LMLQL]NRULVWNDNUPLOQHQDSUDYH
Energy performance of lamp control gear - Part 1: Control gear for fluorescent lamps -
Method of measurement to dertermine the total input power of control gear circuits and
the efficiency of the control gear
Energieeffizienz von Lampenbetriebsgeräten - Teil 1: Betriebsgeräte für
Leuchtstofflampen - Messverfahren zur Bestimmung der Gesamteingangsleistung von
Betriebsgeräteschaltungen und des Wirkungsgrades von Betriebsgeräten
Performance énergétique des appareillages de lampes - Partie 1: Appareillages des
lampes à fluorescence - Méthode de mesure pour la détermination de la puissance
d'entrée totale des circuits d'appareillage et du rendement des appareillages
Ta slovenski standard je istoveten z: EN 62442-1:2011
ICS:
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 62442-1
NORME EUROPÉENNE
November 2011
EUROPÄISCHE NORM
ICS 29.140.99
English version
Energy performance of lamp controlgear -
Part 1: Controlgear for fluorescent lamps -
Method of measurement to determine the total input power of controlgear
circuits and the efficiency of the controlgear
(IEC 62442-1:2011)
Performance énergétique des Energieeffizienz von
appareillages de lampes - Lampenbetriebsgeräten -
Partie 1: Appareillages des lampes à Teil 1: Betriebsgeräte für
fluorescence - Leuchtstofflampen -
Méthode de mesure pour la détermination Messverfahren zur Bestimmung der
de la puissance d'entrée totale des circuits Gesamteingangsleistung von
d'appareillage et du rendement des Betriebsgeräteschaltungen und des
appareillages Wirkungsgrades von Betriebsgeräten
(CEI 62442-1:2011) (IEC 62442-1:2011)

This European Standard was approved by CENELEC on 2011-11-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62442-1:2011 E
Foreword
The text of document 34C/987/FDIS, future edition 1 of IEC 62442-1, prepared by SC 34C, "Auxiliaries for
lamps", of IEC/TC 34, "Lamps and related equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 62442-1:2011.

The following dates are fixed:
(dop) 2012-08-16
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-11-16
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62442-1:2011 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 62442-1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60081 - Double-capped fluorescent lamps - EN 60081 -
Performance specifications
IEC 60901 - Single-capped fluorescent lamps - EN 60901 -
Performance specifications
IEC 60921 2004 Ballasts for tubular fluorescent lamps - EN 60921 2004
Performance requirements
IEC 60929 2011 AC and/or DC-supplied electronic control EN 60929 2011
+ corr. September 2011 gear for tubular fluorescent lamps -
Performance requirements
IEC 61347-2-3 - Lamp controlgear - EN 61347-2-3 -
Part 2-3: Particular requirements for a.c.
and/or d.c. supplied electronic control gear for
fluorescent lamps
IEC 61347-2-8 - Lamp controlgear - EN 61347-2-8 -
Part 2-8: Particular requirements for ballasts
for fluorescent lamps
IEC 62442-1 ®
Edition 1.0 2011-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Energy performance of lamp controlgear –
Part 1: Controlgear for fluorescent lamps – Method of measurement to determine
the total input power of controlgear circuits and the efficiency of the controlgear

Performance énergétique des appareillages de lampes –
Partie 1: Appareillages des lampes à fluorescence – Méthode de mesure pour la
détermination de la puissance d'entrée totale des circuits d'appareillage et du
rendement des appareillages
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX R
ICS 29.140.99 ISBN 978-2-88912-718-4

– 2 – 62442-1 © IEC:2011
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 6
4 General . 8
4.1 Applicability . 8
4.2 Declaration of ballast lumen factor . 8
4.3 Dimmable controlgear . 8
4.4 Multi-wattage and/or multi-lamp controlgear . 8
4.5 Accuracy of measurement . 8
4.6 Sampling of controlgear for testing . 8
4.7 Number of samples. 9
4.8 Conditioning of lamps . 9
4.9 Test voltages and frequencies . 9
5 Method of measurement and calculation of total input power of controlgear –lamp
circuits and the efficiency of controlgear . 9
5.1 Correction for ballast lumen factor . 9
5.2 Method of measurement . 9
5.3 Measurement and calculation of the total input power of magnetic wire wound
controlgear – lamp circuits . 10
5.4 Calculation of the efficiency of magnetic wire wound controlgear . 10
5.5 Measurement and calculation of the total input power of electronic
controlgear –lamp circuits . 10
5.6 Calculation of the efficiency of electronic controlgear . 12
5.7 Measuring the standby power. 12
Annex A (normative) Energy performance measurement setup . 13
Annex B (informative) Application of the reference ballast when assessing lamps in
electronic operation . 17
Bibliography . 18

Figure 1 – Configuration of lamp and photocell sensor . 12
Figure A.1 – Measurement of magnetic wire wound controlgear – lamp circuits . 13
Figure A.2 – Measurement of a.c. supplied electronic controlgear – lamp circuits . 14
Figure A.3 – Test setup for measuring standby power . 14
Figure A.4 – Side view of light output measurement system . 15
Figure A.5 – Top view of light output measurement system . 15

Table 1 – Typical nominal electricity supply details for some regions . 9

62442-1 © IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ENERGY PERFORMANCE OF LAMP CONTROLGEAR –

Part 1: Controlgear for fluorescent lamps –
Method of measurement to determine the total input power
of controlgear circuits and the efficiency of the controlgear

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication
...