EN 61274-1-1:2006

SLOVENSKI STANDARD
01-september-2007
1DGRPHãþD
SIST EN 61274-1-1:1997
3ULODJRGLOQLþOHQLDGDSWHUML]DRSWLþQHNRQHNWRUMH±GHO2NYLUQDSRGUREQD
VSHFLILNDFLMD,(&
Adaptors for fibre optic connectors -- Part 1-1: Blank detail specification (IEC 61274-1-
1:2006)
Kupplungen für Lichtwellenleiter-Steckverbinder - Teil 1-1: Vordruck für
Bauartspezifikation (IEC 61274-1-1:2006)
Raccords de connecteurs de fibres optiques -- Partie 1-1: Spécification particuliere cadre
(IEC 61274-1-1:2006)
Ta slovenski standard je istoveten z: EN 61274-1-1:2006
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61274-1-1
NORME EUROPÉENNE
November 2006
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61274-1-1:1997

English version
Adaptors for fibre optic connectors
Part 1-1: Blank detail specification
(IEC 61274-1-1:2006)
Raccords de connecteurs  Kupplungen für Lichtwellenleiter-
de fibres optiques Steckverbinder
Partie 1-1: Spécification particulière cadre Teil 1-1: Vordruck für Bauartspezifikation
(CEI 61274-1-1:2006) (IEC 61274-1-1:2006)

This European Standard was approved by CENELEC on 2006-10-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61274-1-1:2006 E
Foreword
The text of document 86B/2344/FDIS, future edition 2 of IEC 61274-1-1, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61274-1-1 on 2006-10-01.
This European Standard supersedes EN 61274-1-1:1997.
Specific technical changes from EN 61274-1-1:1997 include increased detail in the work sheet formats,
for example applicable fibre/cable information has been added.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-10-01
__________
Endorsement notice
The text of the International Standard IEC 61274-1-1:2006 was approved by CENELEC as a European
Standard without any modification.
__________
NORME CEI
INTERNATIONALE
IEC
61274-1-1
INTERNATIONAL
QC 860001
STANDARD
Deuxième édition
Second edition
2006-09
Raccords de connecteurs de fibres optiques –
Partie 1-1:
Spécification particulière cadre

Adaptors for fibre optic connectors –
Part 1-1:
Blank detail specification
 IEC 2006 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
M
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

61274-1-1  IEC:2006 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Qualification approval .9
2.1 Procedure.9
2.2 Test schedule and performance requirements.9
3 Quality conformance inspection .9
3.1 Lot-by-lot inspection .9
3.2 Periodic inspection .9
4 Detail specification worksheet .9

61274-1-1  IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
ADAPTORS FOR FIBRE OPTIC CONNECTORS –

Part 1-1: Blank detail specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61274-1-1 had been prepared by subcommittee 86B. Fibre optic
interconnecting devices and passive components of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition of IEC 61274-1-1 published in 1994
and constitutes a technical revision. Specific technical changes since the first edition include
increased detail in the work sheet formats, for example applicable fibre/cable information has
been added.
The text of this standard is based on the following documents:
FDIS Report on voting
86B/2344/FDIS 86B/2391/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

61274-1-1  IEC:2006 – 7 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The QC numbers that appear on the front cover of this publication are the specification
numbers in the IEC Quality Assessment System for Electronic Components (IECQ)
IEC 61274 consists of the following parts, under the general title Adaptors for fibre optic
connectors
Part 1: Generic specification
Part 1-1: Blank detail specification
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
61274-1-1  IEC:2006 – 9 –
ADAPTORS FOR FIBRE OPTIC CONNECTORS –

Part 1-1: Blank detail specification

1 Scope
This blank detail specification is not, by itself, a specification. It is part of the generic
specification IEC 61274-1 (QC 910000). It includes:
– a blank worksheet with instructions for preparing detail specifications.
2 Qualification approval
2.1 Procedure
The detail specification shall state the qualification approval procedure to be used (see 5.3 of
IEC 61274-1, QC 910000)
2.2 Test schedule and performance requirements
The mandatory test schedules for qualification by the fixed sample procedure are defined in
Table 1 of the detail specification worksheet (see Clause 4).
3 Quality conformance inspection
3.1 Lot-by-lot inspection
The mandatory test schedules for lot-by-lot inspection (groups A and B) are defined in Table 2
of the detail specification worksheet (see Clause 4).
3.2 Periodic inspection
The mandatory test schedules for periodic inspection (groups C and D) are defined in Table 3
of the detail specification worksheet (see Clause 4).
4 Detail specification worksheet
The following worksheet is provided to aid in the preparation of detail specifications. Spaces
are provided for entering information. When the spaces are completed, the detail specification
can be drafted in its final form.
The spaces are identified by numbers between brackets. Instructions for completing these
numbered spaces are given below. When drafting the final detail specification, eliminate the
bracketed instruction numbers.
[1] The National IEC number assigned to the detail specification is added by the National
Committee.
[2] The date of the detail specification is added by the National Committee.
[3] Enter the name and address of the National Committee.
[4] Enter the applicable classification categories (see 4.1 of IEC 61274-1) (QC 910000).

61274-1-1  IEC:2006 – 11 –
[5]  Enter the applicable adaptor type.
[6]  Enter the applicable interface standard. If the connector set does not meet an interface
standard, add the words "not applicable".
[7] Enter the performance standard. If the connector set does not meet a performance
standard, add the words "not applicable".
[8]  Enter the applicable assessment level.
[9] Add the qualification procedure required for the detail specification (fixed-sample
procedure or lot-by-lot procedure – see 5.3 of IEC 61274-1).
[10] Enter any applicable fibre / cable information. This is mandatory for terminated connector
sets, i.e. pigtails or patchcords.
[11] Specify the component control dimensions in the format shown (see 4.2.3 of IEC 61274-
1). Include:
– component control dimensions. When a standardised type of connector interface is
referenced, these dimensions shall fall within the mating face dimensions of the
appropriate standard;
– control dimensions for all variants;
– panel cut-out and mounting dimensions where applicable;
– the measurement method(s) to be used when the requirements of 4.2.5.1 of
IEC 61274-1 apply.
Add figures showing the dimensions for standard reference components and gauges if
they are required (see 4.2.5.2 and 4.2.5.3 of IEC 61274-1). Display the drawings in the
format shown.
[12] Tabulate the identification number for each variant of each component (see 4.7.1 of
IEC 61274-1). Assign a column in the table for each variant feature. For example: fibre
size, cable jacket diam
...