EN 61274-1-1:2012

SLOVENSKI STANDARD
01-april-2012
1DGRPHãþD
SIST EN 61274-1-1:2007
3RYH]RYDOQHQDSUDYHLQSDVLYQHNRPSRQHQWHRSWLþQLKYODNHQ3ULODJRGLOQLþOHQL
DGDSWHUML]DRSWLþQHNRQHNWRUMHGHO2NYLUQDSRGUREQDVSHFLILNDFLMD,(&

Fibre optic interconnecting devices and passive components - Adaptors for fibre optic
connectors - Part 1-1: Blank detail specification (IEC 61274-1-1:2011)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Kupplungen für
Lichtwellenleiter-Steckverbinder - Teil 1-1: Vordruck für Bauartspezifikation (IEC 61274-
1-1:2011)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Raccords de
connecteurs de fibres optiques - Partie 1-1: Spécification particulière cadre (CEI 61274-1
-1:2011)
Ta slovenski standard je istoveten z: EN 61274-1-1:2012
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61274-1-1
NORME EUROPÉENNE
February 2012
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61274-1-1:2006

English version
Fibre optic interconnecting devices and passive components -
Adaptors for fibre optic connectors -
Part 1-1: Blank detail specification
(IEC 61274-1-1:2011)
Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive
Raccords de connecteurs de fibres Bauteile -
optiques - Kupplungen für Lichtwellenleiter-
Partie 1-1: Spécification particulière cadre Steckverbinder -
(CEI 61274-1-1:2011) Teil 1-1: Vordruck für Bauartspezifikation
(IEC 61274-1-1:2011)
This European Standard was approved by CENELEC on 2011-12-22. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61274-1-1:2012 E
Foreword
The text of document 86B/3269/FDIS, future edition 3 of IEC 61274-1-1, prepared by SC 86B, "Fibre optic
interconnecting devices and passive components", of IEC/TC 86, "Fibre optics" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61274-1-1:2012.

The following dates are fixed:
(dop) 2012-09-22
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2012-12-22

standards conflicting with the
document have to be withdrawn
This document supersedes EN 61274-1-1:2006.
Specific technical changes since EN 61274-1-1:2006 include to reconsider quality approval and quality
conformance inspection and to add the optical interface standard into the detail specification worksheet.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61274-1-1:2011 was approved by CENELEC as a European
Standard without any modification.

IEC 61274-1-1 ®
Edition 3.0 2011-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Adaptors for
fibre optic connectors –
Part 1-1: Blank detail specification

Dispositifs d’interconnexion et composants passifs à fibres optiques –
Raccords de connecteurs de fibres optiques –
Partie 1-1: Spécification particulière cadre

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX M
ICS 33.180.20 ISBN 978-2-88912-758-0

– 2 – 61274-1-1 © IEC:2011
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Qualification approval . 5
2.1 Procedure . 5
2.2 Test schedule and performance requirements . 5
3 Quality conformance inspection . 5
3.1 Lot-by-lot and periodic procedure . 5
3.2 Lot-by-lot inspection . 5
3.3 Periodic inspection . 5
4 Detail specification worksheet . 6

Table 1 – Fixed sample test schedule for qualification approval [13] . 10
Table 2 – Lot-by-lot quality conformance inspection schedule groups A and B [14] . 10
Table 3 – Periodic quality conformance inspection schedule groups C and D [15] . 11
Table 4 – Details, measurements and performance requirements [16] . 12

61274-1-1 © IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
ADAPTORS FOR FIBRE OPTIC CONNECTORS –

Part 1-1: Blank detail specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61274-1-1 had been prepared by subcommittee 86B. Fibre optic
interconnecting devices and passive components of IEC technical committee 86: Fibre optics.
This third edition cancels and replaces the second edition of IEC 61274-1-1 published in 2006
and constitutes a technical revision. Specific technical changes since the second edition
include to reconsider quality approval and quality conformance inspection and to add the
optical interface standard into the detail specification worksheet.

– 4 – 61274-1-1 © IEC:2011
The text of this standard is based on the following documents:
FDIS Report on voting
86B/3269/FDIS 86B/3299/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61274 series, under the general title Fibre optic interconnecting
devices and passive components – Adaptors for fibre optic connectors can be found on the
IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61274-1-1 © IEC:2011 – 5 –
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
ADAPTORS FOR FIBRE OPTIC CONNECTORS –

Part 1-1: Blank detail specification

1 Scope
This blank detail specification is not, by itself, a specification. It is part of the generic
specification IEC 61274-1, Fibre optic interconnecting devices and passive components-
Adaptors for fibre optic connectors-Part 1; Generic specification. It includes:
– a blank worksheet with instructions for preparing detail specifications.
2 Qualification approval
2.1 Procedure
The detail specification shall state the qualification approval procedure to be used either the
fixed sample or the lot-by-lot and periodic procedure may be used.
2.2 Test schedule and performance requirements
The mandatory test schedules for qualification by the fixed sample procedure are defined in
Table 1 of the detail specification worksheet (see Clause 4).
The fixed sample procedure consists in subjecting a sample of specimens to the fixed sample
qualification test sequence as specified in Table 1. The sample shall be drawn from current
production.
3 Quality conformance inspection
3.1 Lot-by-lot and periodic procedure
The lot-by-lot and periodic procedure consists in performing the lot-by-lot inspections on a
specified number of inspection lots (a minimum of three) taken in as short a time as possible.
The periodic tests are then performed on samples selected from at least one of the lots.
Samples shall be selected from the lots in accordance with IEC 60410. Normal inspection
shall be used, but when the sample size is so small that acceptance based on zero defects is
implied, additional specimens shall be taken to meet the sample size requirements for
acceptance on one defect.
3.2 Lot-by-lot inspection
The mandatory test schedules for lot-by-lot inspection (groups A and B) are defined in Table 2
of the detail specification worksheet (see Clause 4).
3.3 Periodic inspection
The mandatory test schedules for periodic inspection (groups C and D) are defined in Table 3
of the detail specification worksheet (see Clause 4).

– 6 – 61274-1-1 © IEC:2011
4 Detail specification worksheet
The following worksheet is provided to aid in the preparation of detail specifications. Spaces
are provided for entering information. When the spaces are completed, the detail
...