EN IEC 63132-2:2020

SLOVENSKI STANDARD
01-september-2020
Navodila za postopke vgradnje in tolerance hidroelektričnih strojev - 2. del:
Vertikalni generator (IEC 63132-2:2020)
Guide for installation procedures and tolerances of hydroelectric machines - Part 2:
Vertical generator (IEC 63132-2:2020)
Leitfaden für Installations-Prozeduren und -Toleranzen von hydroelektrischen Maschinen
– Teil 2: Vertikale Generatoren (IEC 63132-2:2020)
Guide des procédures et tolérances d'installation des machines hydroélectriques - Partie
2: Alternateur vertical (IEC 63132-2:2020)
Ta slovenski standard je istoveten z: EN IEC 63132-2:2020
ICS:
27.140 Vodna energija Hydraulic energy engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63132-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS 27.140
English Version
Guidance for installation procedures and tolerances of
hydroelectric machines - Part 2: Vertical generators
(IEC 63132-2:2020)
Lignes directrices des procédures et tolérances Leitfaden für Installations-Prozeduren und -Toleranzen von
d'installation des machines hydroélectriques - Partie 2: hydroelektrischen Maschinen - Teil 2: Vertikale
Alternateurs verticaux Generatoren
(IEC 63132-2:2020) (IEC 63132-2:2020)
This European Standard was approved by CENELEC on 2020-05-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63132-2:2020 E

European foreword
The text of document 4/381/FDIS, future edition 1 of IEC 63132-2, prepared by IEC/TC 4 "Hydraulic
turbines" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-25
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 63132-2:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 63132-1 NOTE Harmonized as EN IEC 63132-1
IEC 63132-3 NOTE Harmonized as EN IEC 63132-3
IEC 63132-4 NOTE Harmonized as EN IEC 63132-4

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60034-7 - Rotating electrical machines - Part 7: Classification - -
of types of construction, mounting arrangements
and terminal box position (IM Code)

Third edition under preparation. Stage at the time of publication: IEC/ACDV 60034-7:2019.
IEC 63132-2 ®
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Guidance for installation procedures and tolerances of hydroelectric machines –

Part 2: Vertical generators
Lignes directrices des procédures et tolérances d’installation des machines

hydroélectriques –
Partie 2: Alternateurs verticaux

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.140 ISBN 978-2-8322-8102-4

– 2 – IEC 63132-2:2020  IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Preparation . 6
5 Installation flowchart . 6
6 Steps . 8
6.1 Step 1: Turbine shaft free . 8
6.2 Step 2: Generator foundation check . 8
6.3 Step 3-1: Lower bracket assembly . 8
6.4 Step 3: Lower bracket installation . 9
6.5 Step 4: Lower bracket bases embedment . 9
6.6 Step 5-1: Stator assembly . 9
6.7 Step 5: Stator installation . 10
6.8 Step 6: Thrust and guide bearing assembly . 10
6.9 Step 7: Brakes and jacks installation . 11
6.10 Step 8: Lower generator shaft installation . 11
6.11 Step 9: Thrust block installation . 11
6.12 Step 10-1: Rotor assembly . 11
6.13 Step 10: Rotor installation . 12
6.14 Step 11: Upper shaft installation . 13
6.15 Step 12-1: Upper bracket assembly . 13
6.16 Step 12: Upper bracket installation . 13
6.17 Step 13: Uncoupled generator shafts runout check . 14
6.18 Step 14: Turbine and generator shafts coupling . 14
6.19 Step 15: Unit alignment . 15
6.20 Step 16: Upper bracket and/or stator bases embedment . 18
6.21 Step 17: Generator guide bearings assembly and adjustment . 19
6.22 Step 18: Slip (collector) rings installation and runout checks . 19
6.23 Step 19: Brush holder supporting structure and brushes installation . 19
6.24 Step 20: Remaining generator parts installation completion . 19
6.25 Step 21: Cleaning, painting and inspection before initial tests . 20
6.26 Step 22: Generator complete . 20
6.27 Step 23: Commissioning . 20
Bibliography . 21

Figure 1 – Generic installation flowchart – Generator . 7
Figure 2 – Stator and rotor magnetic centre . 17
Figure 3 – Unit alignment (thrust bearing below the rotor) . 18

Table 1 – Runout and shaft verticality . 15
Table 2 – Circularity, concentricity and verticality . 16
Table 3 – Air gap . 16

IEC 63132-2:2020  IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
GUIDANCE FOR INSTALLATION PROCEDURES
AND TOLERANCES OF HYDROELECTRIC MACHINES –

Part 2: Vertical generators
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility tha
...