EN 62841-2-14:2015

SLOVENSKI STANDARD
01-december-2015
1DGRPHãþD
SIST EN 60745-2-14:2009
SIST EN 60745-2-14:2009/A2:2010
(OHNWULþQDPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO3RVHEQH]DKWHYH]DURþQHVNREHOMQLNH
Electric Motor- Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 2-14: Particular requirements for hand-held planers
Ta slovenski standard je istoveten z: EN 62841-2-14:2015
ICS:
25.080.25 6WURML]DSORãþLQVNRREGHODYR Planing machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62841-2-14

NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2015
ICS 25.140.20 Supersedes EN 60745-2-14:2009
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-14: Particular
requirements for hand-held planers
(IEC 62841-2-14:2015 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-14: Exigences transportable Werkzeuge und Rasen- und
particulières pour les raboteuses portatives Gartenmaschinen - Sicherheit - Teil 2-14: Besondere
(IEC 62841-2-14:2015 , modifiée) Anforderungen für handgeführte Hobel
(IEC 62841-2-14:2015 , modifiziert)
This European Standard was approved by CENELEC on 2015-08-31. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-2-14:2015 E
European foreword
The text of document 116/222/FDIS, future edition 1 of IEC 62841-2-14, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-2-14:2015.
A draft amendment, which covers common modifications to IEC 62841-2-14:2015 (116/222/FDIS), was
prepared by CLC/TC 116, "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
(dop) 2016-08-31
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2019-08-31
document have to be withdrawn
This document will supersede EN 60745-2-14:2009 + A2:2010.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 2 is to be used in conjunction with EN 62841-1:2015. When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
This Part 2 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for hand-held planers.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EU Directives can be applicable to the products falling within
the scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-2-14:2015 are prefixed “Z”.
Endorsement notice
The text of the International Standard IEC 62841-2-14:2015 was approved by CENELEC as a European
Standard with agreed common modifications.
COMMON MODIFICATIONS
21 Construction
Replace the existing subclause 21.18.1.1 with the following:
21.18.1.1 Addition:
For planers, the power switch shall not have any locking device to lock it in the “on” position.

Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions

Annex K
(normative)
Battery tools and battery packs

Add the following new subclause:
K.21.18.Z101 Isolation device
Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury
from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.
Annex L
(normative)
Battery tools and battery packs provided
with mains connection or non-isolated sources

Add the following new subclause:
L.21.18.Z101 Isolation device
Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury
from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.

Add the following annex:
Annex ZZ
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within
the scope of this standard.
IEC 62841-2-14 ®
Edition 1.0 2015-06
INTERNATIONAL
STANDARD
Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –
Part 2-14: Particular requirements for hand-held planers

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.140.20 ISBN 978-2-8322-2770-1

– 2 – IEC 62841-2-14:2015 © IEC 2015
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 5
4 General requirements . 5
5 General conditions for the tests . 5
6 Radiation, toxicity and similar hazards . 6
7 Classification . 6
8 Marking and instructions . 6
9 Protection against access to live parts . 6
10 Starting . 6
11 Input and current . 7
12 Heating . 7
13 Resistance to heat and fire . 7
14 Moisture resistance . 7
15 Resistance to rusting . 7
16 Overload protection of transformers and associated circuits . 7
17 Endurance . 7
18 Abnormal operation . 7
19 Mechanical hazards . 8
20 Mechanical strength . 10
21 Construction . 10
22 Internal wiring . 11
23 Components . 11
24 Supply connection and external flexible cords . 11
25 Terminals for external conductors . 11
26 Provision for earthing . 11
27 Screws and connections . 11
28 Creepage distances, clearances and distances through insulation . 11
Annexes . 14
Annex I (informative) Measurement of noise and vibration emissions .
...