EN 16282-6:2020

SLOVENSKI STANDARD
01-maj-2020
Oprema za profesionalne kuhinje - Sestavni deli za prezračevanje kuhinj - 6. del:
Izločevalniki aerosolov - Projektiranje in varnostne zahteve
Equipment for commercial kitchens - Components for ventilation in commercial kitchens -
Part 6: Aerosol separators - Design and safety requirements
Einrichtungen in gewerblichen Küchen - Elemente zur Be- und Entlüftung - Teil 6:
Aerosolabscheider - Gestaltungs- und Sicherheitsanforderungen
Équipement pour cuisines professionnelles - Éléments de ventilation pour cuisines
professionnelles - Partie 6 : Séparateurs d'aérosols - Conception et exigences de
sécurité
Ta slovenski standard je istoveten z: EN 16282-6:2020
ICS:
91.140.30 Prezračevalni in klimatski Ventilation and air-
sistemi conditioning systems
97.040.99 Druga kuhinjska oprema Other kitchen equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16282-6
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2020
EUROPÄISCHE NORM
ICS 97.040.99
English Version
Equipment for commercial kitchens - Components for
ventilation in commercial kitchens - Part 6: Aerosol
separators; Design and safety requirements
Équipement pour cuisines professionnelles - Éléments Einrichtungen in gewerblichen Küchen - Elemente zur
de ventilation pour cuisines professionnelles - Partie 6 Be- und Entlüftung - Teil 6: Aerosolabscheider;
: Séparateurs d'aérosols; Conception et exigences de Gestaltungs- und Sicherheitsanforderungen
sécurité
This European Standard was approved by CEN on 26 August 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16282-6:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Designation for separators . 5
5 Construction and function . 6
5.1 General . 6
5.2 Materials . 6
6 Requirements of technical safety . 7
6.1 General . 7
6.2 Flame penetration . 7
7 Hygienic requirements. 8
7.1 General . 8
7.2 General hygienic requirements . 8
8 Flame penetration of the separator . 8
8.1 Test device . 8
8.2 Inspection of flame penetration . 9
8.2.1 General . 9
8.2.2 Assembly of test samples in the testing equipment . 10
8.2.3 Flame penetration . 10
9 Test report . 10
9.1 General . 10
9.2 Data of test sample . 11
10 Product supervision . 11
11 Instructions for assembly and operation . 11
12 Marking . 12
Bibliography . 13
European foreword
This document (EN 16282-6:2020) has been prepared by Technical Committee CEN/TC 156
“Ventilation for buildings”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2020, and conflicting national standards shall be
withdrawn at the latest by July 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
The activities of CEN/TC 156/WG 14, cover the calculation of the air volume and the design and testing
of major components of ventilation equipment for commercial kitchens.
The structure of the standard series is as follows:
EN 16282 Equipment for commercial kitchens – Components for ventilation in commercial kitchens
— Part 1: General requirements including calculation method
— Part 2: Kitchen ventilation hoods; Design and safety requirements
— Part 3: Kitchen ventilation ceilings; Design and safety requirements
— Part 4: Air inlets and outlets; Design and safety requirements
— Part 5: Air duct; Design and dimensioning
— Part 6: Aerosol separators; Design and safety requirements
— Part 7: Installation and use of fixed fire suppression systems
— Part 8: Installations for treatment of cooking fumes; Requirements and testing
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
1 Scope
This document specifies requirements covering the design, construction, installation and operation of
aerosol separators to be used in ventilation systems, including technical safety, ergonomic and hygienic
features.
This document is applicable to ventilation systems in commercial kitchens, associated areas and other
installations processing foodstuffs intended for commercial use. Kitchens and associated areas are
special rooms in which meals are prepared, where tableware and equipment is washed, cleaned and
where food is stored and food waste areas.
This document is applicable to aerosol separator except for those used in domestic kitchens.
A method of verification of each requirement is also specified.
Unless otherwise specified, it is expected that the requirements of this standard will be checked by way
of inspection and/or measurement.
NOTE Additional or alternative national regulations on installation, appliance requirements and inspection,
maintenance and operation could exit.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10088-1, Stainless steels — Part 1: List of stainless steels
EN 16282-2, Equipment for commercial kitchens — Components for ventilation in commercial kitchens —
Part 2: Kitchen ventilation hoods; design and safety requirements
EN 16282-3, Equipment for commercial kitchens — Components for ventilation in commercial kitchens —
Part 3: Kitchen ventilation ceilings; design and safety requirements
EN 16282-4, Equipment for commercial kitchens — Components for ventilation in commercial kitchens —
Part 4: Air inlets and outlets; design and safety requirements
EN ISO 3274, Geometrical product specifications (GPS) — Surface texture: Profile method — Nominal
characteristics of contact (stylus) instruments (ISO 3274)
EN ISO 4287, Geometrical product specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters (ISO 4287)
EN ISO 4288, Geometrical product specifications (GPS) — Surface texture: Profile method — Rules and
procedures for the assessment of surface texture (ISO 4288)
EN ISO 13565-1, Geometrical product specifications (GPS) — Surface texture: Profile method; surfaces
having stratified functional properties — Part 1: Filtering and general measurement conditions (ISO
13565-1)
EN ISO 13565-2, Geometrical product specifications (GPS) — Surface texture: Profile method; surfaces
having stratified functional properties — Part 2: Height characterization using the linear material ratio
curve (ISO 13565-2)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
kitchen
part of a building where cooking processes are carried out, their connecting floors and distribution
corridors, ancillary rooms such as food stores, cold rooms, food preparation areas and appliances are
being cleaned
3.2
separator
device for the efficient separation of airborne solid or liquid particles, based on the effect of mechanical
forces that deflect the particles out of the airflow
3.3
filter
specific design of storage separators comprising an ordered and/or unordered structure of a number of
individual fibres, wire mesh or porous surfaces/bodies
EXAMPLE An example of fibres/wires filter is fabric filters and an example of porous surfaces/bodies is
activated carbon.
3.4
combination separator
combination of aerosol separator (no storage) and filter (storage)
3.5
aerosol
separated grease/oil/water mixture
3.6
flame penetration
penetration of flames through a separator
4 Designation for separators
Designation for separators is shown in Table 1.
Table 1 — Designation for separators
Design Standard designation
Designation EN number Classification
Separator for ceilings/ separator EN 16282-6 –F-1
a
hoods conforming to the flame penetration test
Separator for ceilings/ separator EN 16282-6 –F-2
hoods not conforming to the flame penetration
a
test
a
The flame penetration test is specified in 6.2.
EXAMPLE Designation for a separator for ceilings/hoods conforming to flame penetration test:
separator EN 16282-6-F-1
5 Construction and function
5.1 General
Unless otherwise specified the requirements shall be verified by way of inspection and/or subsequent
measurement.
Filters are not permitted unles
...