Railway applications - Railway rolling stock - Draw gear and screw coupling

This standard specifies the requirements for the draw gear and screw coupling for the end of rolling stock that has to couple with other rolling stock (freight wagons, locomotives, passenger vehicles ...).
This standard covers the functionality, construction, interfaces and testing including pass/fail criteria for draw gear and screw coupling.
The standard describes three categories of classification of draw gear and screw coupling, (1 MN, 1,2 MN and 1,5 MN).
Permanent coupling systems are not in the scope of this standard.

Bahnanwendungen - Schienenfahrzeuge - Zugeinrichtung und Schraubenkupplung

Diese Norm legt die Anforderungen an Zugeinrichtungen und Schraubenkupplungen für Endwagen fest, die mit anderen Schienenfahrzeugen (Güterwagen, Lokomotiven, Reisezugwagen ...) gekuppelt werden.
Diese Norm umfasst die Funktionalität, Bauweise, Schnittstellen und Prüfungen, einschließlich der Abnahmekriterien für Zugeinrichtungen und Schraubenkupplungen.
In dieser Norm sind drei Kategorien von Zugeinrichtungen und Schraubenkupplungen beschrieben (1 MN, 1,2 MN und 1,5 MN).
Dauerhafte Kupplungssysteme sind vom Anwendungsbereich dieser Norm ausgeschlossen.

Applications ferroviaires - Matériel roulant ferroviaire - Organes de traction et tendeur d'attelage

La présente norme spécifie les exigences relatives aux organes de traction et tendeurs d'attelage pour un matériel roulant devant être couplé à un autre matériel roulant  (wagons de marchandises, locomotives, voitures, etc.).
La présente norme couvre la fonctionnalité, la construction, les interfaces et les essais, y compris les critères de réussite/d'échec aux essais pour les organes de traction et les tendeurs d'attelage.
La norme décrit trois catégories pour les organes de traction et les tendeurs d'attelage (1 MN, 1,2 MN et 1,5 MN).
Les systèmes d’attelage permanents ne font partie du domaine d’application de la présente norme.

Železniške naprave - Železniška vozila - Vlečna naprava in vijačna spenjača

Ta standard določa zahtevo za vlečno napravo in vijačno spenjačo končnega vozila, ki se mora speti z drugimi interoperabilnimi vozili (tovorni vagoni, lokomotive, potniška vozila, ...).
Ta standard zajema funkcionalnost, sestavo, vmesnike in preskušanje, vključno z merili za uspešno/neuspešno opravljen preskus, za vlečno napravo in vijačno spenjačo.
Standard opisuje tri razvrstitvene kategorije vlečne naprave in vijačne spenjače (1 MN, 1,2 MN in 1,5 MN).

General Information

Status
Withdrawn
Publication Date
27-Sep-2016
Withdrawal Date
30-Aug-2022
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
31-Aug-2022

Relations

Buy Standard

Standard
EN 15566:2016
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST EN 15566:2009+A1:2010
äHOH]QLãNHQDSUDYHäHOH]QLãNDYR]LOD9OHþQDQDSUDYDLQYLMDþQDVSHQMDþD
Railway applications - Railway rolling stock - Draw gear and screw coupling
Bahnanwendungen - Schienenfahrzeuge - Zugeinrichtung und Schraubenkupplung
Applications ferroviaires - Matériel roulant ferroviaire - Organes de traction et tendeur
d'attelage
Ta slovenski standard je istoveten z: EN 15566:2016
ICS:
45.060.10 9OHþQDYR]LOD Tractive stock
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 15566
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 45.060.01 Supersedes EN 15566:2009+A1:2010
English Version
Railway applications - Railway rolling stock - Draw gear
and screw coupling
Applications ferroviaires - Matériel roulant ferroviaire Bahnanwendungen - Schienenfahrzeuge -
- Organes de traction et tendeur d'attelage Zugeinrichtung und Schraubenkupplung
This European Standard was approved by CEN on 8 July 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15566:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 7
Introduction . 9
1 Scope . 10
2 Normative references . 10
3 Terms and definitions . 11
4 Requirements for all types of draw gear and screw coupling. 13
4.1 Classification and designation . 13
4.2 Interaction coupling/buffer . 13
4.3 Interface dimension for freight wagons. 14
4.4 Life time . 15
5 Draw gear . 16
5.1 Draw gear components . 16
5.2 Draw hook and drawbar – Requirements . 18
6 Screw coupling . 18
6.1 General requirements . 18
6.2 Screw coupling – Requirements. 20
7 Elastic device . 20
7.1 Characteristics of elastic device . 20
7.2 Elastic device – Requirements . 21
Annex A (normative) Dynamic test (fatigue test) procedure . 22
A.1 Background . 22
A.2 Performance of the test . 22
A.2.1 Conditioning . 22
A.2.2 Dynamic test (fatigue test) . 22
A.2.3 Non-destructive tests . 24
A.2.4 Determination of residual strength . 24
A.2.5 Macrographic and Micrographic tests . 24
A.3 Criteria of acceptance . 24
Annex B (normative) Draw hook – dimensions. 25
Annex C (normative) Draw gear – Interface dimension . 26
Annex D (normative) Screw coupling components – dimensions . 27
Annex E (normative) Draw hook and drawbar – Requirements . 29
E.1 Physical characteristics . 29
E.1.1 Appearance . 29
E.1.2 Integrity . 29
E.1.3 Material examination . 29
E.2 Geometrical characteristics . 30
E.3 Mechanical characteristics . 30
E.3.1 Tensile test on test piece . 30
E.3.2 Resilience. 30
E.3.3 Hardness . 30
E.3.4 Tensile test on draw hook and draw bar . 30
E.3.5 Compressive test on draw hook for locomotives . 31
E.4 Marking . 31
E.5 Manufacture. 31
E.5.1 General on draw bars . 31
E.5.2 General on draw hooks . 31
E.5.3 Machining . 31
E.5.4 Heat treatment . 31
E.5.5 Rectification of defects. 32
E.6 Acceptance . 32
E.6.1 General . 32
E.6.2 Inspection of the draw hooks . 32
E.6.3 Inspection of draw bars . 37
E.6.4 Conclusion of the inspections . 38
E.7 Delivery . 38
E.7.1 Protection against oxidation . 38
E.7.2 Packaging . 38
Annex F (normative) Screw coupling and component parts – Requirements . 39
F.1 Material . 39
F.2 Physical characteristics . 39
F.2.1 Appearance . 39
F.2.2 Soundness . 39
F.2.3 Additional requirements for screw couplings . 40
F.3 Geometrical characteristics . 40
F.3.1 General . 40
F.3.2 Dimensions limited either by two unmachined or rough-machined surfaces or by
one unmachined or rough-machined surface . 40
F.3.3 Dimensions limited by two machined surfaces . 41
F.4 Mechanical characteristics . 41
F.4.1 Heat treatment . 41
F.4.2 Hardness . 41
F.4.3 Values for predetermined breaking loads for the weakest part. 41
F.4.4 Resilience . 42
F.4.5 Requirements for screw coupling . 42
F.4.6 Requirement for handle and trunnion . 43
F.5 Marking .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.