EN ISO 13385-2:2020

SLOVENSKI STANDARD
01-september-2020
Nadomešča:
SIST EN ISO 13385-2:2011
Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dimenzij - 2.
del: Konstrukcijske in meroslovne karakteristike meril za merjenje globin (ISO
13385-2:2020)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2:
Design and metrological characteristics of calliper depth gauges (ISO 13385-2:2020)
Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Teil 2:
Tiefenmessschieber; Konstruktionsmerkmale und messtechnische Anforderungen (ISO
13385-2:2020)
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel
- Partie 2: Caractéristiques de conception et caractéristiques métrologiques des jauges
de profondeur (ISO 13385-2:2020)
Ta slovenski standard je istoveten z: EN ISO 13385-2:2020
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 13385-2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 17.040.30 Supersedes EN ISO 13385-2:2011
English Version
Geometrical product specifications (GPS) - Dimensional
measuring equipment - Part 2: Design and metrological
characteristics of calliper depth gauges (ISO 13385-
2:2020)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Équipement de mesurage dimensionnel - Partie 2: Längenmessgeräte - Teil 2: Tiefenmessschieber;
Caractéristiques de conception et caractéristiques Konstruktionsmerkmale und messtechnische
métrologiques des jauges de profondeur (ISO 13385- Anforderungen (ISO 13385-2:2020)
2:2020)
This European Standard was approved by CEN on 22 March 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13385-2:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 13385-2:2020) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards
shall be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13385-2:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 13385-2:2020 has been approved by CEN as EN ISO 13385-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 13385-2
Second edition
2020-05
Geometrical product specifications
(GPS) — Dimensional measuring
equipment —
Part 2:
Design and metrological
characteristics of calliper depth gauges
Spécification géométrique des produits (GPS) — Équipement de
mesurage dimensionnel —
Partie 2: Caractéristiques de conception et caractéristiques
métrologiques des jauges de profondeur
Reference number
ISO 13385-2:2020(E)
©
ISO 2020
ISO 13385-2:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 13385-2:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design characteristics . 2
4.1 General design and nomenclature . 2
4.2 Dimensions . 4
5 Metrological characteristics . 4
5.1 General . 4
5.2 Rated operating conditions . 4
5.3 Reference point . 4
5.4 Test methods . 5
5.5 Partial surface contact error, E (limited by E ) . 5
MPE
5.6 Shift error, S (limited by S ) . 6
MPE
5.7 MPE values. 7
5.8 Special cases . 7
6 Determination of conformity to specifications . 8
6.1 General . 8
6.2 Measurement uncertainty . 8
6.3 Decision rule . 8
7 Marking . 9
Annex A (informative) Calibration guidelines for metrological characteristics .10
Annex B (normative) Default MPE values for metrological characteristics .11
Annex C (informative) Relation to the GPS matrix model .12
Bibliography .13
ISO 13385-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 290, Dimensional and geometrical product specification and verification, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 13385-2:2011), which has been technically
revised.
The main changes to the previous edition are as follows:
— figures have been updated to show more modern technology;
— general design characteristics have been removed and reference to ISO 14978:2018 included;
— metrological characteristics have been clarified and modified;
— requir
...