EN 13071-2:2008
(Main)Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
This European Standard specifies the additional requirements for underground or partly underground systems top lifted and bottom emptied, used for collection of solid non-hazardous wastes with a capacity up to 5 000 l.
Stationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und Bodenentleerung - Teil 2: Zusätzliche Anforderungen für unterirdische oder teilweise unterirdische Systeme
Diese Europäische Norm legt die zusätzlichen Anforderungen für unterirdische oder teilweise unterirdische Systeme mit Behälteraufnahme an der Oberseite und Bodenentleerung fest, welche für die Sammlung von festen, ungefährlichen Abfallstoffen, mit einem Volumen bis 5 000 l genutzt werden.
Conteneurs fixes à déchets de capacité inférieure ou égale à 5 000 l, levés par le haut et vidés par le bas - Partie 2 : Exigences complémentaires relatives aux systèmes enterrés ou semi-enterrés
La présente Norme européenne spécifie les exigences complémentaires qui s’appliquent aux systèmes enterrés ou semi-enterrés, levés par le haut et vidés par le bas, utilisés pour la collecte de déchets solides non dangereux, d’une capacité inférieure ou égales à 5 000 l.
Nepremični zabojniki za odpadke do 5000 l, ki se dvigujejo zgoraj in praznijo spodaj - 2. del: Dodatne zahteve za podzemne ali delno podzemne sisteme
Ta dokument opredeljuje dodatne zahteve za podzemne ali delno podzemne sisteme, ki se dvigujejo zgoraj in praznijo spodaj in se uporabljajo za zbiranje trdnih nenevarnih odpadkov s kapaciteto do 5.000 l.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN 13071:2004
1HSUHPLþQL]DERMQLNL]DRGSDGNHGRONLVHGYLJXMHMR]JRUDMLQSUD]QLMR
VSRGDMGHO'RGDWQH]DKWHYH]DSRG]HPQHDOLGHOQRSRG]HPQHVLVWHPH
Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2:
Additional requirements for underground or partly underground systems
Stationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und
Bodenentleerung - Teil 2: Zusätzliche Anforderungen für unterirdische oder teilweise
unterirdische Systeme
Conteneurs fixes de capacité < 5 000 l, levés par le haut et vidés par le bas - Partie 2:
Spécifications complémentaires relatives aux systèmes enterrés ou semi-enterrés
Ta slovenski standard je istoveten z: EN 13071-2:2008
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13071-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 13.030.40 Supersedes EN 13071:2002
English Version
Stationary waste containers up to 5 000 l, top lifted and bottom
emptied - Part 2: Additional requirements for underground or
partly underground systems
Conteneurs fixes de capacité < 5 000 l, levés par le haut et Stationäre Abfallsammelbehälter bis 5 000 l, mit
vidés par le bas - Partie 2: Spécifications complémentaires Behälteraufnahme an der Oberseite und Bodenentleerung -
relatives aux systèmes enterrés ou semi-enterrés Teil 2: Zusätzliche Anforderungen für unterirdische oder
teilweise unterirdische Systeme
This European Standard was approved by CEN on 18 April 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13071-2:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .5
4 Requirements.6
4.1 General requirements.6
4.2 Design .6
4.3 Safety requirements .7
4.3.1 Hole .7
4.3.2 Pedestrian platform .7
4.3.3 Safety floor .7
4.3.4 Safety barrier.7
5 Test conditions .7
6 Test procedures.8
6.1 Tests conducted on the container .8
6.2 Specific tests conducted on underground and partly underground systems .8
6.2.1 Resistance of the safety barrier .8
6.2.2 Resistance of the safety floor.8
6.2.3 Functionality of the safety floor and safety barrier.9
6.2.4 Resistance of the pedestrian platform .9
6.2.5 Resistance of the emergent part to exterior impacts.9
6.3 Corrosion.11
6.4 Weathering (for thermoplastics only).11
6.4.1 Requirement.11
6.4.2 Procedure .11
6.5 Sequence of tests .11
7 Recommendations.12
8 Data sheet.12
9 Marking .12
10 Test report .12
Annex A (informative) A–deviations.13
Figures
Figure 1 — Underground and partly underground system . 5
Figure 2 — Example of resistance of emergent part to exterior impacts . 10
Tables
Table 1 — Sequence of the tests. 12
Foreword
This document (EN 13071-2:2008) has been prepared by Technical Committee CEN/TC 183 “Waste
Management”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn
at the latest by December 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document, together with EN 13071-1:2008, supersedes EN 13071:2002.
Part 1 covers the general requirements for stationary waste containers up to 5 000 l, top lifted and bottom
emptied. Some technical changes respect to the previous edition, EN 13071:2002, address:
a) the minimum capacity of 80 l which has been deleted;
b) the definitions of, and general requirements for Type A and Type B containers;
c) test conditions including a new test on the resistance of the roof;
d) changes to data sheet, marking and test report;
e) deletion of Annex A dealing with the noise test method for containers for waste glass collection for Type A
and Type B, with volumes greater than or equal to 500 l.
Part 2 covers additional requirements for underground or partly underground containers.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
1 Scope
This European Standard specifies the additional requirements for underground or partly underground systems
top lifted and bottom emptied, used for collection of solid non-hazardous wastes with a capacity up to 5 000 l.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming - Technical
delivery conditions
EN 13071-1:2008, Stationary waste containers up to 5 000 l, top lifted and bottom emptied – Part 1: General
requirements
EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles – Specifications and test
methods (ISO 1461:1999)
ISO 2081, Metallic coatings – Electroplated coatings of zinc on iron or steel
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13071-1:2008 and the following
apply.
3.1
underground or partly underground system
system whose emptying device is located below surrounding ground level at any point
a) partly underground system b) underground system
Key
C container
EP emergent part
H housing
L liner
LC lifting connection
PP pedestrian platform
R roof
Figure 1 — Underground and partly underground system
3.2
container
mobile part of underground or partly underground system, designated to collect/receive the waste
3.3
liner
equipment installed fully or partly in the ground, whose function is to receive the container
3.4
housing
part of the container that is fixed to the pedestrian platform, above ground level, that is used to fill the
container
3.5
pedestrian platform
part of the system to which the housing is fixed or is used by pedestrians to walk on to fill the container
3.6
emergent part
part of the liner that permanently emerges from surrounding ground level
3.7
hole
space below ground level that is left by the container when it is removed from the liner
3.8
safety barrier
moving part of the system that prevents accidental access to the hole left by the container when it is removed
from the liner
3.9
safety floor
moving part of the system that covers the hole left by the container when it is removed from the liner
4 Requirements
4.1 General requirements
See EN 13071-1:2008, Clause 4.
4.2 Design
The liner shall be resistant to withstand ground pressure and shall be secured against floating or sinking.
The liner shall be designed and built to allow easy cleaning and pumping out of any fluids that have leaked
from the container.
The container shall retain residual liquids up to a minimum of 2 % of the nominal volume.
Safety devices shall be resistant to all weather conditions, moisture and dirt that could negatively affect their
functionality.
For maintenance and cleaning, all parts of the underground or partly underground system shall be easily
accessible.
If present, the pedestrian platform shall be designed in order to prevent accidental slipping and tripping of
pedestrians.
4.3 Safety requirements
4.3.1 Hole
During supervised operations, the hole if deeper than 500 mm measured at any point shall be equipped with
safety device(s) in order to prevent anyone accidentally falling into it, or being injured by any moving parts of
the system.
The safety device can be either a safety floor or a safety barrier.
If, when the container is removed, the emergent part is a minimum of 900 mm above ground level at any point,
no other safety device will be required to protect accidental falls into the hole.
In all cases, the safety device(s) shall be highly visible or sensitive to pedestrians.
If the hole is left unsupervised, it shall be covered by a specific device that shall resist a minimum load of
500 kg/m² on every point applied on a circle of a diameter of 200 mm.
4.3.2 Pedestrian platform
When the co
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.