EN ISO 1403:1997

SLOVENSKI STANDARD
01-december-2000
6WHNVWLORPRMDþHQHJXPHQHFHYL]DVSORãQRQDPHQVNRXSRUDERYRGH
6SHFLILNDFLMD,62
Rubber hoses, textile-reinforced, for general-purpose water applications - Specification
(ISO 1403:1995)
Gummischläuche mit Textileinlage für allgemeine Anwendungen mit Wasser -
Anforderung (ISO 1403:1995)
Tuyaux en caoutchouc a armature textile d'usage général pour l'eau - Spécifications
(ISO 1403:1995)
Ta slovenski standard je istoveten z: EN ISO 1403:1997
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL
ISO
STANDARD 1403
Third edition
1995-08-01
Rubber hoses, textile-reinforced, for
general-purpose water applications -
Specification
Tuyaux en caoutchouc a armature ’textile d ’usage g&&ral pour I’eau -
Spkifica tions
Reference number
ISO 1403:1995(E)
ISO 1403:1995(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1403 was prepared by Technical Committee
lSO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses
(rubber and plastics).
This third edition cancels and replaces the second edition
(ISO 1403:1986), which has been technically revised.
0 ISO 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 l Switzerland
Printed in Switzerland
ii
INTERNATIONAL STANDARD 0 ISO
ISO 1403:1995(E)
Rubber hoses, textile-reinforced, for general-purpose
water applications - Specification
ISO 1307:1992, Rubber and plastics hoses for
1 Scope
general-purpose indus trial applica tions - Bore diam-
eters and tolerantes, and tolerantes on length.
This International Standard specifies the requirements
for three types of general-purpose textile-reinforced
ISO 1402:1994, Rubber and plastics hoses and hose
rubber water hose with an operating range of
assemblies - H ydros ta tic tes ting.
-
25 “C to + 70 “C, and a maximum working pressure
of up to 2,5 MPa.
ISO 2393:1994, Rubber test mixes - Preparation,
mixing and vulcanization - Equipment and pro-
These hoses should not be used for conveyance
NOTE 1
cedures.
of potable (drinking) water, for washing-machine inlets, as
fire-fighting hose, for special agricultural machines and as
collapsible water hose. ISO 4671: 1984, Rubber and plastics hose and hose
assemblies
- Methods of measurement of dimen-
sions.
ISO 4672:~ ‘1, Rubber and plastics hoses -
Subambien t-tempera ture flexibility tes ts.
2 Normative references
ISO 7326:1991, Rubber and plastics hoses - As-
sessmen t
The following Standards contain provisions which, of ozone resis tance under static
conditions.
through reference in this text, constitute provisions
of this International Standard. At the time of publi-
ISO 8033:1991, Rubber and plastics hose - Deter-
cation, the editions indicated were valid. All Standards
mina tion o f adhesion be tween componen ts.
are subject to revision, and P
...