prEN ISO 10833

SLOVENSKI STANDARD
01-september-2024
Tekstilne talne obloge - Ugotavljanje odpornosti rezanih robov proti poškodbam z
modificiranim bobnastim preskusom po Vettermannu (ISO/DIS 10833:2024)
Textile floor coverings - Determination of resistance to damage at cut edges using the
modified Vettermann drum test (ISO/DIS 10833:2024)
Textile Bodenbeläge - Bestimmung der Schnittkantenfestigkeit mit der modifizierten
Vettermann-Trommelprüfung (ISO/DIS 10833:2024)
Revêtements de sol textiles - Détermination de la résistance des joints par l'essai au
tambour Vettermann modifié (ISO/DIS 10833:2024)
Ta slovenski standard je istoveten z: prEN ISO 10833
ICS:
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 10833
ISO/TC 219
Textile floor coverings —
Secretariat: NBN
Determination of resistance to
Voting begins on:
damage at cut edges using the
2024-06-27
modified Vettermann drum test
Voting terminates on:
2024-09-19
Revêtements de sol textiles — Détermination de la résistance des
joints par l'essai au tambour Vettermann modifié
ICS: 97.150
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 10833:2024(en)
DRAFT
ISO/DIS 10833:2024(en)
International
Standard
ISO/DIS 10833
ISO/TC 219
Textile floor coverings —
Secretariat: NBN
Determination of resistance to
Voting begins on:
damage at cut edges using the
modified Vettermann drum test
Voting terminates on:
Revêtements de sol textiles — Détermination de la résistance des
joints par l'essai au tambour Vettermann modifié
ICS: 97.150
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 10833:2024(en)
ii
ISO/DIS 10833:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Vettermann-drum tester .2
5.2 Steel ball .2
5.3 Rubber studs .3
5.4 External vacuum cleaner .3
5.5 Fixation tape (single-sided adhesive tape) .3
5.6 Double sided adhesive tape .3
5.7 Knife .3
6 Sampling and preparation of specimens . . 3
6.1 Sampling .3
6.1.1 General .3
6.1.2 Broadloom materials .4
6.1.3 Tiles/planks .4
6.2 Preparation of specimens .5
6.2.1 Broadloom materials .5
6.2.2 Tiles/planks .5
7 Atmosphere for conditioning and testing . 5
8 Procedures . 5
9 Assessment . . 6
10 Test report . 6

iii
ISO/DIS 10833:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received notice of
(a) patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 219, Floor coverings.
This fourth edition cancels and replaces the third edition (ISO 10833:2017), which has been technically
revised.
The main changes are as follows:
— 3.6 adding the definition of filamentation;
— 6.1.3 adding planks and how to cut;
— 9 better wording for evaluation of assessment and adding also the criterium for filamentation.
A list of all parts in the ISO 10833 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
DRAFT International Standard ISO/DIS 10833:2024(en)
Textile floor coverings — Determination of resistance to
damage at cut edges using the modified Vettermann drum test
1 Scope
This document describes a method to determine the susceptibility of textile floor coverings to mechanical
damage at cut edges.
It is applicable to all textile floor coverings both as broadloom materials and as tiles/planks.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 139, Textiles — Standard atmospheres for conditioning and testing
ISO 1957, Machine-made textile floor coverings — Selection and cutting of specimens for physical tests
ISO 2424, Textile floor coverings — Vocabulary
ISO 9405, Textile floor coverings — Assessment of changes in appearance
ISO 10361:2015, Textile floor coverings — Production of changes in appearance by means of Vettermann drum
and hexapod tumbler tester
3 Terms and definitions
For the purposes of this document the following terms and definitions apply in addition to those in ISO 2424.
3.1
delamination
separation of the use-surface and/or foundation/primary substrate of a textile floor covering from the
secondary backing
3.2
fraying
damage or loss of pile or substrate material of a textile floor covering from a cut edge
3.3
tufting out
loss of tufts from the use-surface of a textile floor covering
3.4
sprouting
release and appearance during use of extra-long tuft legs, which were accidentally trapped within the pile of
a textile floor covering during manufacture
3.5
laddering/shooting
loss of consecutive loops of the same column from the use-surface of a textile floor covering

ISO/DIS 10833:2024(en)
3.6
filamentation, hairiness
the protrusion of fibers above the normal level of the use-surface of a textile floor covering and not removable
by brushing or suction
4 Principle
A steel
...