EN ISO 9431:1999

SLOVENSKI STANDARD
01-februar-2002
Gradbeniške risbe - Prostori za risbe, besedila in glave na risalnem listu (ISO
9431:1990)
Construction drawings - Spaces for drawing and for text, and title blocks on drawing
sheets (ISO 9431:1990)
Zeichnungen für das Bauwesen - Anordnung von Darstellungen, Texten und
Schriftfeldern auf Zeichnungsvordrucken (ISO 9431:1990)
Dessins de construction - Zones réservées au dessin et au texte, et cartouches
d'inscription sur les feuilles de dessin (ISO 9431:1990)
Ta slovenski standard je istoveten z: EN ISO 9431:1999
ICS:
01.100.30 *UDGEHQLQDþUWL Construction drawings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

ISO
INTERNATIONAL
STANDARD 9431
First edi tion
1990-12-15
-- ---
Construction drawings - Spates for drawing
and for text, and title blocks on drawing skeets
Dessins de construction - Zones r&erv&es au dessin et au texte, et
cartouches d’inscription SW- les feuilies de dessin
Reference number
ISO 9431: 199O(E)
ISO 9431:199O(E)
Forewsrd
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the
work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an Inter-
national Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard ISO 9431 was prepared by Technical Committee
ISO/TC IO, Technical drawings, product definition and related docnmen-
tation.
Annex A of this International Standard is for information only.
0 ISO 1990
All rights reserved. No part of this publication may be reproduced or utilized in any form
or by any means, electronie or mechanical, including photocopying and microfiIm, without
Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-121 1 Geneve 20 l Switzerland
Printed in Switzerland
ii
INTERNATIONAL STANDARD ISO 9431:1990(E)
Construction drawings - Spates for drawing and for text, and
title blocks on drawing sheets
the top left of the drawing or at the top left of a group
1 Scope
of figures. lf possible, consideration shall be taken
of A4-size folds of a drawing sheet when figures are
This International Standard specifies requirements
drawn.
concerning the placing, layout and contents of
spaces for drawing and for text, and title blocks on
construction drawings.
5 Spate for text
2 Normative references 5.1 General
The following Standards contain provisions which, The space for text on a drawing sheet shall contain
through reference in this text, constitute provisions all information necessary for the understanding of
of this International Standard. At the time of publi- the contents of the drawing (see 5.2), except for the
cation, the editions indicated were valid. All stan- text which needs to be placed adjacent to the figures
dards are subject to revision, and Parties to in the space for drawing.
agreements based on this International Standard
The space for text shall normally be placed at the
are encouraged to investigate the possibility of ap-
right-hand edge of the drawing sheet (see figure 1);
plying the most recent editions of the Standards in-
the width of the space shall be equal to that of the
dicated below. Members of IEC and ISO maintain
title block, i.e. maximum 170 mm, or at least
registers of currently valid International Standards.
100 mm.
ISO 3098-1:1974, Technical dra
...