EN ISO 22477-1:2018
(Main)Geotechnical investigation and testing - Testing of geotechnical structures - Part 1: Testing of piles: static compression load testing (ISO 22477-1:2018, Corrected version 2019-03)
Geotechnical investigation and testing - Testing of geotechnical structures - Part 1: Testing of piles: static compression load testing (ISO 22477-1:2018, Corrected version 2019-03)
This document establishes the specifications for the execution of static pile load tests in which a single pile is subjected to an axial static load in compression in order to define its load-displacement behaviour.
This document is applicable to vertical piles as well as raking piles.
All types of piles are covered by this document. The tests considered in this document are limited to maintained load tests. Pile load tests with constant penetration rate and cyclic load tests are not covered by this document.
NOTE This document is intended to be used in conjunction with EN 1997-1. EN 1997-1 provides numerical values of partial factors for limit states and of correlation factors to derive characteristic values from static pile load tests to be taken into account in design.
This document provides specifications for the execution of static axial pile load tests:
a) checking that a pile will behave as designed;
b) measuring the resistance of a pile.
Geotechnische Erkundung und Untersuchung - Prüfung von geotechnischen Bauwerken und Bauwerksteilen - Teil 1: Statische axiale Pfahlprobebelastungen auf Druck (ISO 22477-1:2018, korrigierte Fassung 2019-03)
Dieses Dokument enthält Festlegungen für die Durchführung von axialen statischen Pfahlprobebelastungen auf Druck an Einzelpfählen um deren Last Setzungs Verhalten zu bestimmen.
Dieses Dokument ist sowohl für vertikale als auch für geneigte Pfähle anwendbar.
Dieses Dokument ist für alle Pfahlarten anwendbar. Die hier enthaltenen Festlegungen gelten nur für lastgesteuerte Probebelastungen. Weggesteuerte Pfahlprobebelastungen und zyklischen Probebelastungen werden durch dieses Dokument nicht abgedeckt.
ANMERKUNG Dieses Dokument ist in Verbindung mit EN 1997 1 anzuwenden. EN 1997 1 enthält Zahlenwerte für die Teilsicherheitsbeiwerte für Grenzzustände und Korrelationsfaktoren, aus denen die für die Bemessung maßgebenden charakteristischen Werte aus den statischen Pfahlprobebelastungen abgeleitet werden.
Dieses Dokument enthält Festlegungen für die Ausführung statischer Pfahlprobebelastungen zur:
a) Überprüfung, ob das Pfahltragverhalten mit der Bemessung übereinstimmt;
b) Messung des Pfahlwiderstands.
Reconnaissance et essais géotechniques - Essais de structures géotechniques - Partie 1: Essais de pieux: essai de chargement statique en compression (ISO 22477-1:2018, Version corrigée 2019-03)
La présente norme établit les spécifications relatives à l'exécution des essais de pieux sous charge statique, au cours desquels un pieu unique est soumis à une charge de compression axiale statique afin de définir son comportement charge-déplacement.
Ce document s'applique aussi bien aux pieux verticaux qu'aux pieux inclinés.
La présente norme couvre tous les types de pieux. Les essais envisagés dans cette norme sont limités aux essais de chargement par paliers. Les essais de chargement de pieux à vitesse de pénétration constante et les essais de chargement cyclique ne sont pas couverts par la présente norme.
NOTE Cette norme est à utiliser conjointement avec l'EN 1997‑1. La norme EN 1997‑1 fournit les valeurs numériques des facteurs partiels pour les états limites et des facteurs de corrélation servant à obtenir les valeurs caractéristiques à partir d'essais de chargement statique et devant être prises en compte dans la conception.
La présente norme fournit des spécifications pour l'exécution de l'essai de chargement axial statique de pieu pour:
a) vérifier qu'un pieu se comporte comme prévu;
b) mesurer la résistance d'un pieu.
Geotehnično preiskovanje in preskušanje - Preskušanje geotehničnih konstrukcij - 1. del: Preskušanje nosilnih pilotov s statično osno stiskalno obremenitvijo (ISO 22477-1:2018)
Ta standard podaja specifikacije za izvedbo preskusov pilotov s statično obremenitvijo, pri čemer je posamezen pilot izpostavljen statični osni obremenitvi pri stiskanju, da se lahko določi njegovo vedenje ob premiku bremena. Določbe iz standarda EN 22477-1 se uporabljajo za navpične in nagnjene pilote. Ta standard obravnava vse vrste pilotov. Preskusi v tem standardu so omejeni na preskuse z vzdrževano obremenitvijo. Standard EN 22477-1 je treba uporabljati v povezavi s standardom EN 1997-1. Številske vrednosti delnih faktorjev za mejna stanja in faktorjev korelacije za izpeljavo karakterističnih vrednosti iz preskusov pilotov s statično obremenitvijo, ki jih je treba upoštevati pri izdelavi, so navedene v standardu EN 1997-1. Smernice za analizo rezultatov preskusov z obremenitvijo so podane v informativnem dodatku D. Ta standard podaja specifikacije za: a) preiskovalne preskuse, pri čemer je pilot obremenjen do okvare ali skoraj do okvare; b) kontrolne preskuse, pri čemer je pilot obremenjen do določenega bremena, ki presega mejno stanje uporabnosti (SLS).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2019
*HRWHKQLþQRSUHLVNRYDQMHLQSUHVNXãDQMH3UHVNXãDQMHJHRWHKQLþQLKNRQVWUXNFLM
GHO 3UHVNXãDQMHQRVLOQLKSLORWRYVVWDWLþQRRVQRVWLVNDOQRREUHPHQLWYLMR ,62
Geotechnical investigation and testing - Testing of geotechnical structures - Part 1:
Testing of piles: static compression load testing (ISO 22477-1:2018)
Geotechnische Erkundung und Untersuchung - Prüfung von geotechnischen Bauwerken
und Bauwerksteilen - Teil 1: Pfahlprobebelastungen durch statische axiale
Druckbelastungen (ISO 22477-1:2018)
Reconnaissance et essais géotechniques - Essais de structures géotechniques - Partie
1: Essais de pieux: essai de chargement statique en compression (ISO 22477-1:2018)
Ta slovenski standard je istoveten z: EN ISO 22477-1:2018
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 22477-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 93.020
English Version
Geotechnical investigation and testing - Testing of
geotechnical structures - Part 1: Testing of piles: static
compression load testing (ISO 22477-1:2018)
Reconnaissance et essais géotechniques - Essais de Geotechnische Erkundung und Untersuchung - Prüfung
structures géotechniques - Partie 1: Essais de pieux: von geotechnischen Bauwerken und Bauwerksteilen -
essai de chargement statique en compression (ISO Teil 1: Pfahlprobebelastungen durch statische axiale
22477-1:2018) Druckbelastungen (ISO 22477-1:2018)
This European Standard was approved by CEN on 10 November 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22477-1:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 22477-1:2018) has been prepared by Technical Committee ISO/TC 182
"Geotechnics" in collaboration with Technical Committee CEN/TC 341 “Geotechnical Investigation and
Testing” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22477-1:2018 has been approved by CEN as EN ISO 22477-1:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 22477-1
First edition
2018-11
Geotechnical investigation and
testing — Testing of geotechnical
structures —
Part 1:
Testing of piles: static compression
load testing
Reconnaissance et essais géotechniques — Essais des structures
géotechniques —
Partie 1: Essais de pieux: essai de chargement statique en
compression
Reference number
ISO 22477-1:2018(E)
©
ISO 2018
ISO 22477-1:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 22477-1:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 1
3.1 Terms and definitions . 2
3.2 Symbols . 2
4 Equipment . 3
4.1 General . 3
4.2 Reaction device . 3
4.3 Force input . 5
4.3.1 General. 5
4.3.2 Specifications of force input . 5
4.4 Measurement of pile head displacements . 5
4.5 Measurement of pile load . 6
4.6 Pile instrumentation . 7
5 Test procedure . 7
5.1 Test preparation . 7
5.1.1 Protections . 7
5.1.2 Construction of a test pile . 8
5.1.3 Test date . 8
5.1.4 Preparation of the pile cap . 9
5.2 Loading procedure . 9
5.2.1 General. 9
5.2.2 Load step sequence and duration of load steps for one cycle procedure . 9
5.2.3 Load step sequence and duration of load steps for multiple cycle procedure .10
5.2.4 Maximum test load F .11
p
5.2.5 Measuring intervals .11
6 Test report .12
6.1 General .12
6.2 General information .12
6.3 Data report .13
6.4 Interpretative report .14
Annex A (informative) Critical creep load in compression .21
Annex B (informative) Bi-directional load testing .22
ISO 22477-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.