prEN 18064-5

SLOVENSKI STANDARD
01-april-2024
Polimerni materiali - Priporočila za kakovost in podlaga za specifikacije za
uporabo polimernih reciklatov v izdelkih - 5. del: Poli(vinilklorid) (PVC)
Plastics - Quality recommendations and basis for specifications for application of plastic
recyclates in products - Part 5 : Poly(vinyl chloride) (PVC)
Kunststoffe - Qualitätsempfehlungen und Grundlagen für Spezifikationen für die
Verwendung von Kunststoffrezyklaten in Produkten - Teil 5: Poly(Vinylchlorid) (PVC)
Plastiques - Recommandations qualité et base de spécification pour l’application des
recyclats de plastiques dans les produits - Partie 5 : Poly(chlorure de vinyle) (PVC)
Ta slovenski standard je istoveten z: prEN 18064-5
ICS:
13.030.50 Recikliranje Recycling
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2024
ICS 83.140.01; 13.030.50; 83.080.01
English Version
Plastics - Quality recommendations and basis for
specifications for application of plastic recyclates in
products - Part 5 : Poly(vinyl chloride) (PVC)
Kunststoffe - Qualitätsempfehlungen und Grundlagen
für Spezifikationen für die Verwendung von
Kunststoffrezyklaten in Produkten - Teil 4:
Poly(Vinylchlorid) (PVC)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18064-5:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 7
4 Categorization of polyvinylchloride (PVC) applications and requirements . 7
5 Selection of relevant properties for polyvinylchloride (PVC) recyclates . 7
6 Typical range for characteristics of product families . 7
7 Designation of polyvinylchloride (PVC) recyclates . 7
Annex A (normative) Designatory properties polyvinylchloride recyclate . 8
A.1 Generic and additional designatory properties . 8
A.2 Designation of polyvinylchloride recyclate . 8
A.2.1 General. 8
A.2.2 Data block 1 . 8
A.2.3 Data block 2 . 9
A.2.4 Data block 3 . 9
A.2.5 Data block 4 . 9
A.2.5.1 General. 9
A.2.5.2 Vicat softening temperature . 10
A.2.5.3 Impact strength . 10
A.2.5.4 Modulus of elasticity . 11
A.2.6 Data block 5 . 11
A.2.7 Designation examples . 12
A.2.7.1 First designation example from EN ISO 21306-1 . 12
Annex B (normative) Typical values for product families . 13
B.1 Typical values . 13
Bibliography . 20

European foreword
This document (prEN 18064-5:2024) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by SIS.
This document is currently submitted to the CEN Enquiry.
This document is part of the EN 18064-series, currently consisting of all parts as listed below. This series
of standards consists of a general part 1, and material specific parts for different types of plastics. This
particular part covers typical values (ranges, or min/max values) for polyvinylchloride (PVC) general
purpose plastics, that can be composed of 100 % recyclates (mechanical and/or chemical), or a
combination of recyclates and virgin plastic.
This part is supported by other standards on test methods to which references are made throughout this
document.
EN 18064, Plastics — Quality recommendations and basis for specifications for application of plastic
recyclates in products, is currently composed with the following parts:
— Part 1: General aspects
— Part 2: Polyethylene (PE)
— Part 3: Polypropylene (PP)
— Part 4: Poly(ethylene terephthalate) (PET)
— Part 5: Poly(vinyl chloride) (PVC)
— Part 6: Polystyrene (PS)
— Part 7: Acrylonitrile-butadiene-styrene (ABS)
NOTE Part 6 for PS also includes EPS and XPS.
Introduction
See prEN 18064-1.
1 Scope
This document provides relevant characteristics and typical values for poly(vinyl chloride) (PVC)
recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the
performance requirements of the products belonging to that family, including requirements for product
manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate)
products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes
the designation system for plastic recyclates. The designation system allows comparison between
recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1 Examples of designations of plastic recyclates are given in Annex A.
NOTE 2 The selection of relevant properties for a product family is based on EN ISO 10350-1, extended with
specific properties related to plastic recyclates.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
CEN/TR 15353, Plastics - Recycled plastics - Guidelines for the development of standards for recycled
plastics
prEN 18604-1 , Plastics — Quality recommendations and basis for specifications for application of plastic
recyclates in products — Part 1: General aspects
EN 12608 (all parts), Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and
doors — Classification, requirements and test methods
EN 15346, Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
EN 17410, Plastics - Controlled loop recycling of PVC-U profiles from windows and doors
EN ISO 60, Plastics - Determination of apparent density of material that can be poured from a specified
funnel (ISO 60)
EN ISO 178, Plastics - Determination of flexural properties (ISO 178)
EN ISO 179-1, Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test
(ISO 179-1)
EN ISO 179-2, Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO
179-2)
ISO 182-1, Plastics — Determination of the tendency of compounds and products based on vinyl chloride
homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated
temperatures — Part 1: Congo red method

Under preparation.
EN ISO 182-2, Plastics - Determination of the tendency of compounds and products based on vinyl chloride
homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated
temperatures - Part 2: pH method (ISO 182-2)
EN ISO 182-3, Plastics - Determination of the tendency of compounds and products based on vinyl chloride
homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated
temperatures - Part 3: Conductometric method (ISO 182-3)
EN ISO 182-4, Plastics - Determination of the tendency of compounds and products based on vinyl chloride
homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated
temperatures - Part 4: Potentiometric method (ISO 182-4)
EN ISO 306, Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)
(ISO 306)
EN ISO 472:2013, Plastics - Vocabulary (ISO 472:2013)
EN ISO 527-1, Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1)
EN ISO 527-2, Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and
extrusion plastics (ISO 527-2)
EN ISO 527-3, Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO
527-3)
EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore
hardness) (ISO 868)
EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special
characteristics (ISO 1043-1)
EN ISO 1183-1, Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion
method, liquid pycnometer method and titration method (ISO 1183-1:2019, Corrected version 2019-05)
EN ISO 1269, Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile
matter (including water) (ISO 1269)
EN ISO 3451-5, Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 6186, Plastics - Determination of pourability (ISO 6186)
EN ISO 21306-1, Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials -
Part 1: Designation system and basis for specifications (ISO 21306-1)
EN ISO 21306-2, Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials -
Part 2: Preparation of test specimens and determination of properties (ISO 21306-2)
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 472:2013, CEN/TR 15353
and the following apply.
ISO and IEC maintain terminol
...