83.140.01 - Rubber and plastics products in general

This document specifies fundamental radiographic techniques which enable repeatable results to be obtained economically.
This document applies to the X-ray radiographic examination of heated tool, electrofusion, extrusion and hot gas joints in plastics materials.
It applies to joints in single wall pipes and plates with a range of thicknesses from 5 mm to 100 mm. It only applies to pipes containing air or other gases at the time of X-ray testing.
This document does not specify acceptance leve...view more

This document specifies possible manufacturing tolerances for plastic moulded parts. This document specifies all integral features with general tolerances with surface profile tolerance within a specified datum system. It allows for additional specifications in case of functional needs and requirements using the ISO-GPS-tools for dimensional and geometrical tolerating. This document addresses injection moulding, injection compression moulding, transfer moulding, compression moulding and rotation...view more

This European Standard covers the visual examination of welds in thermoplastic materials. It may also be applied to visual testing of the joint prior to and during the welding.

ISO 15082:2016 specifies commonly used test methods relating to the safety requirements for rigid plastic safety glazing materials in a road vehicle, regardless of the type of plastic of which they are composed.

ISO 11469:2016 specifies a system of uniform marking of products that have been fabricated from plastics materials. Provision for the process or processes to be used for marking is outside the scope of this International Standard.
NOTE 1 Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate location of the marking, are subject to agreement between the manufacturer and the user.
The marking system is intended to help identify ...view more

ISO 3302-1:2014 specifies classes of dimensional tolerances and their values for moulded, extruded, and calendared solid rubber products. The relevant test methods necessary for the establishment of compliance with ISO 3302-1:2014 are also specified. The tolerances are primarily intended for use with vulcanized rubber but can also be suitable for products made of thermoplastic rubbers. ISO 3302-1:2014 does not apply to precision toroidal sealing rings or to calendared composite products such as ...view more

This European Standard specifies the equipment and methods for the high voltage testing of butt or overlap welded joints in thermoplastic sheets for locating through-thickness defects only. It applies to new unused constructions only.

ISO 15791-1:2014 provides a framework guide for the development and use of intermediate-scale fire tests for products made of or containing plastics. The guidance identifies typical applications of plastics products and possible fire scenarios that can arise involving products in these applications. The development and use of intermediate-scale tests is described to ensure their relevance to the end use of the product.

ISO 6072:2011 specifies test methods for evaluating the effect of hydraulic fluids on standard elastomeric materials that have been manufactured in accordance with specified processes. It allows baseline comparisons of fluids with standard elastomers. The standard provides formulations, mixing procedures and vulcanization procedures for five types of elastomeric composition: acrylonitrile-butadiene rubbers (NBR 1 and NBR 2), fluorocarbon rubber (FKM 2), ethylene propylene diene rubber (EPDM 1) a...view more

ISO/TR 24699:2009 provides guidelines for inclusion of environmental aspects in standards for rubber and rubber products. It proposes an approach which is directed at minimizing any adverse environmental impact of the products under consideration without detracting from the primary purpose of ensuring their adequate fitness for use. It closely follows the guidelines laid down in ISO 17422, with certain modifications to make it applicable to rubber and rubber products. The guidance provided by IS...view more

ISO 3302-2:2008 specifies the following geometrical tolerances for moulded and extruded solid rubber products, including those with metal inserts: flatness tolerance; parallelism tolerance; perpendicularity tolerance; coaxiality tolerance; positional tolerance. The tolerances are primarily intended for use with vulcanized rubber but may also be suitable for products made of thermoplastic rubbers.

This part of ISO 13000 specifies the  preparation of test specimens and gives the  test methods applicable to semi-finished  products of polytetrafluoroethylene (PTFE).

This part of ISO 13000 specifies the  requirements for processed unfilled  polytetrafluoroethylene (PTFE) products,  which may occur in several forms. The  PTFE used to make the semi-finished  product is described in ISO 12086-1 and, as  provided in ISO 12086-1, may contain up to  1 % of a comonomer. The PTFE used to  make the semi-finished product may be  virgin, reprocessed or recycled resin. The  addition of up to 1, 5 % by mass of pigment  or colorant is permitted. This part of ISO  13000 al...view more

ISO 13000-1:2005 specifies the requirements for processed unfilled polytetrafluoroethylene (PTFE) products which may occur in several forms. The PTFE used to make the semi-finished product is described in ISO 12086-1 and, as provided in ISO 12086-1, may contain up to 1 % of a comonomer. The PTFE used to make the semi-finished product may be virgin, reprocessed or recycled resin. The addition of up to 1,5 % by mass of pigment or colorant is permitted. This part of ISO 13000 allows for four grades...view more

ISO 13000-2:2005 specifies the preparation of test specimens and gives the test methods applicable to semi-finished products of polytetrafluoroethylene (PTFE).

ISO 13000-1:2005 specifies the requirements for processed unfilled polytetrafluoroethylene (PTFE) products which may occur in several forms. The PTFE used to make the semi-finished product is described in ISO 12086-1 and, as provided in ISO 12086-1, may contain up to 1 % of a comonomer. The PTFE used to make the semi-finished product may be virgin, reprocessed or recycled resin. The addition of up to 1,5 % by mass of pigment or colorant is permitted. This part of ISO 13000 allows for four grades...view more