prEN 18348

SLOVENSKI STANDARD
01-julij-2026
Polimerni materiali - Lastna biorazgradljivost - Merila in preskusne metode
Plastics - Intrinsic biodegradability - Criteria and test methods
Kunststoffe - Intrinsische biologische Abbaubarkeit - Kriterien und Prüfverfahren
Plastiques - Biodégradabilité intrinsèque - Critères et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 18348
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2026
ICS 83.080.01
English Version
Plastics - Intrinsic biodegradability - Criteria and test
methods
Plastiques - Biodégradabilité intrinsèque - Critères et Kunststoffe - Intrinsische biologische Abbaubarkeit -
méthodes d'essai Kriterien und Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18348:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 7
4 Principles . 7
5 Requirements . 9
5.1 Materials . 9
5.2 Test methods . 9
5.3 Biodegradability criteria. 10
5.4 Negative side effects . 11
6 Test report .11
Bibliography .12

European foreword
This document (prEN 18348:2026) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by SIS.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Introduction
Human activities take place within the so-called technosphere, i.e. the system of structures and artefacts
that humans have built over time. With the aim of preserving the natural environment, products are
manufactured, consumed, recycled and disposed of within the technosphere, avoiding as far as possible
their uncontrolled release into the biosphere, understood as the natural environment populated by living
beings. This applies to all products, including biodegradable products, which are also used within the
technosphere and recovered through separate collection and organic recycling in waste treatment
facilities, where they undergo controlled biological processes (such as composting).
Therefore, littering (i.e. the improper disposal of waste in public places or in the natural environment,
resulting in pollution and adverse effects on the environment) is not an action that can be justified or
considered acceptable, as it is never without negative consequences, large or small.
However, there are products that are used in applications that are inherently at risk of uncontrolled
release from the technosphere. For example, tools used in fishing, aquaculture, and mussel farming are
subject to breakage and dispersal because they are immersed in seawater and exposed to the aggressive
action of the sea (storm surges, erosion, etc.). Normally these products are intended to be recovered and
brought ashore for recycling or disposal, but occasionally they break and are dispersed.
Then there are other products that are deliberately released into the biosphere because of the way they
are used. Fireworks, for example, are fired into the air and, when they burst, they break into pieces that
fall to the ground below with little chance of being recovered.
The designer involved in the development of these applications with a high risk of uncontrolled release
is interested in knowing the biodegradability of different materials in order to reduce the ecological risk
of man-made products entering the environment. It is therefore necessary to develop a framework
methodology for the definition of principles, test methods and criteria for the biodegradability of
applications with a risk of dispersion, which can be applied across the sectors concerned without
unnecessary multiplication of approaches.
The methodologies and criteria described in this document may not be appropriate if the release into the
environment occurs in areas where constant anaerobic conditions are expected, such as deep ocean
sediments.
1 Scope
This document defines test methods and criteria for distinguishing intrinsically biodegradable plastic
materials from those that are persistent. Biodegradability is inferred from biodegradation tests
conducted under aerobic conditions, i.e. under the conditions typically found in most natural habitats.
Plastics that undergo ultimate biodegradation under aerobic conditions in a manner similar to natural
polymer materials are defined as biodegradable plastics. This document describes a method for
distinguishing between non-biodegradable plastics, which do not biodegrade even when environmental
conditions are favourable for biodegradation (including aerobic conditions), and biodegradable plastics,
i.e. those that biodegrade upon contact with active microorganisms when environmental conditions are
favourable for biodegradation.
The aim is to demonstrate ultimate aerobic biodegradability of plastic materials, i.e. the intrinsic potential
for conversion to carbon dioxide, water and biomass by aerobic microorganisms in an oxygen-rich
environment, which is representative of most natural environments.
The potential for biodegradation should be verified using alternative tests and criteria, if a deposition in
a permanent anaerobic environment (e.g. deep subsurface environments, wetlands and swamps, anoxic
zones in oceans and lakes) is expected.
NOTE Currently, there are no methodologies or criteria available to verify accumulation due to the lack of
biodegradation of plastics in such anaerobic habitats.
The plastic materials identified as intrinsically biodegradable following this document can be used in the
design of products with a high risk of dispersion whenever the use of biodegradable components is
searched by the designer. Intrinsically non-biodegradable components are not susceptible to
biodegradation and therefore cannot be removed from the environment by the action of micro-
organisms. This factor tends to increase the residence time of products in the environment. In addition,
their eventual degradation, mainly due to abiotic factors, results in persistent fragments (microplastics).
The test scheme described in this document is not specific to any particular application. Rather, it is a
framework methodology that can be used in different industries to identify biodegradable plastics that
can be used to make different types of products and for different applications. For the characterisation
and environmental assessment of products placed on the market containing plastics identified as
biodegradable according to this document, reference is made to the specific product standards, where
available. This document only deals with the definition of intrinsic biodegradability of plastic materials,
without defining the hazard of the products, which requires a specific assessment that is beyond the
scope of this document. The rate of biodegradation of a plastic object as a function of environmental
conditions cannot be determined from this document. Therefore, this document is not sufficient to carry
out an analysis of the ecological risk associated with the dispersal of products, as this requires an
assessment of the intrinsic hazard, of the environmental fate, in addition to the assessment of
biodegradability.
The methodology described in this document does not apply to applications covered by mandatory
regulations.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 5430, Plastics — Ecotoxicity testing scheme for soluble decomposition intermediates from
biodegradable plastic materials and products used in the marine environment — Test methods and
requirements
EN ISO 17556, Plastics — Determination of the ultimate aerobic biodegradability of plastic materials in soil
by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved
EN ISO 18830, Plastics — Determination of aerobic biodegradation of non-floating plastic materials in a
seawater/sandy sediment interface — Method by measuring the oxygen demand in closed respirometer
EN ISO 19679, Plastics — Determination of aerobic biodegradation of non-floating plastic materials in a
seawater/sediment interface — Method by analysis of evolved carbon dioxide
EN ISO 22404, Plastics — Determination of the aerobic biodegradation of non-floating materials exposed
to marine sediment — Method by analysis of evolved carbon dioxide
ISO 23517, Plastics — Soil biodegradable materials for mulch films for use in agriculture and horticulture
— Requirements and test methods regarding biodegradation, ecotoxicity and control of constituents
EN ISO 23977-1, Plastics — Determination of the aerobic biodegradation of plastic materials exposed to
seawater — Part 1: Method by analysis of evolved carbon dioxide
EN ISO 23977-2, Plastics — Determination of the aerobic biodegradation of plastic materials exposed to
seawater — Part 2: Method by measuring the oxygen demand in closed respirometer
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
intrinsic biodegradability
potential of a polymer or plastic material to be biodegraded established under controlled laboratory
conditions
3.2
ultimate biodegradation
breakdown of an organic chemical compound by microorganisms in the presence of oxygen to carbon
dioxide, water, and mineral salts of any other elements present (mineralization) and new biomass or in
the absence of oxygen to carbon dioxide, methane, mineral salts, and new biomass
3.3
constituent
every pure chemical material or substance of which a polymer or plastic material is composed
4 Principles
Human activities occur within the technosphere, a system of human-made structures and artifacts. To
protect the natural environment (biosphere), products are manufactured, used, recycled, and disposed
of within the technosphere. However, some products, like fishing gear and fireworks, are prone to
uncontrolled release into the biosphere due to their usage conditions. Designers of such products aim to
understand the environmental impact of materials to minimize ecological risks.
As is well known, risk assessment involves knowledge of the hazard and the potential harm caused by
the stressor. The term hazard is used to describe a stre
...