Fishing nets - Method of test for the determination of mesh size - Part 1: Opening of mesh (ISO 16663-1:2009)

ISO 16663-1:2009 specifies a method for the determination of the size of the mesh opening of fishing nets, using an objective mesh gauge. It is applicable to active and passive fishing gear.

Fischnetze - Prüfverfahren zur Bestimmung der Maschenweite - Teil 1: Maschenöffnung (ISO 16663-1:2009)

Diese Norm legt ein Verfahren zur Bestimmung der Größe der Maschenöffnung von Fischnetzen mit einer objektiven Maschenmesslehre fest. Sie ist für Aktiv- und Passiv-Fischgeschirre anwendbar.

Filets de pêche - Méthode d'essai pour la détermination des dimensions de la maille - Partie 1: Ouverture de maille (ISO 16663-1:2009)

L'ISO 16663-1:2009 spécifie une méthode de détermination des dimensions de l'ouverture de maille des filets de pêche à l'aide d'une jauge objective de maille. Elle est applicable aux engins de pêche actifs et passifs.

Ribiške mreže - Metoda preskušanja določevanja zančne velikosti - 1. del: Odpiranje zanke (ISO 16663-1:2009)

General Information

Status
Published
Publication Date
28-Feb-2009
Withdrawal Date
29-Sep-2009
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
01-Mar-2009
Completion Date
01-Mar-2009

Relations

Buy Standard

Standard
EN ISO 16663-1:2009
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2009
1DGRPHãþD
SIST EN ISO 16663-1:2003
5LELãNHPUHåH0HWRGDSUHVNXãDQMDGRORþHYDQMD]DQþQHYHOLNRVWLGHO
2GSLUDQMH]DQNH ,62
Fishing nets - Method of test for the determination of mesh size - Part 1: Opening of
mesh (ISO 16663-1:2009)
Fischnetze - Prüfverfahren zur Bestimmung der Maschenweite - Teil 1: Maschenöffnung
(ISO 16663-1:2009)
Filets de pêche - Méthode d'essai pour la détermination des dimensions de la maille -
Partie 1: Ouverture de maille (ISO 16663-1:2009)
Ta slovenski standard je istoveten z: EN ISO 16663-1:2009
ICS:
65.150 Ribolov in ribogojstvo Fishing and fish breeding
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 16663-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 65.150 Supersedes EN ISO 16663-1:2003
English Version
Fishing nets - Method of test for the determination of mesh size -
Part 1: Opening of mesh (ISO 16663-1:2009)
Filets de pêche - Méthode d'essai pour la détermination Fischnetze - Prüfverfahren zur Bestimmung der
des dimensions de la maille - Partie 1: Ouverture de maille Maschenweite - Teil 1: Maschenöffnung (ISO 16663-
(ISO 16663-1:2009) 1:2009)
This European Standard was approved by CEN on 28 February 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16663-1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 16663-1:2009) has been prepared by Technical Committee ISO/TC 38 "Textiles" in
collaboration with Technical Committee CEN/TC 248 "Textiles and textile products", the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2009, and conflicting national standards shall be
withdrawn at the latest by September 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 16663-1:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 16663-1:2009 has been approved by CEN as a EN ISO 16663-1:2009 without any
modification.
INTERNATIONAL ISO
STANDARD 16663-1
Second edition
2009-03-01
Fishing nets — Method of test for the
determination of mesh size —
Part 1:
Opening of mesh
Filets de pêche — Méthode d'essai pour la détermination des
dimensions de la maille —
Partie 1: Ouverture de maille
Reference number
ISO 16663-1:2009(E)
©
ISO 2009
ISO 16663-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

ISO 16663-1:2009(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle. 2
5 Apparatus . 2
6 Measurement force. 4
7 Calibration . 4
8 Verification of length and force measurement . 4
9 Requirements for testing . 5
10 Procedure . 6
11 Calculation and expression of results. 7
12 Test report . 8

ISO 16663-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16663-1 was prepared by Technical Committee ISO/TC 38, Textiles.
This second edition cancels and replaces the first edition (ISO 16663-1:2003), which has been technically
revised.
ISO 16663 consists of the following parts, under the general title Fishing nets — Method of test for the
determination of mesh size:
⎯ Part 1: Opening of mesh
⎯ Part 2: Length of mesh
iv © ISO 2009 – All rights reserved

INTERNATIONAL STANDARD ISO 16663-1:2009(E)

Fishing nets — Method of test for the determination of mesh
size —
Part 1:
Opening of mesh
1 Scope
This part of ISO 16663 specifies a method for the determination of the size of the mesh opening of fishing nets,
using an objective mesh gauge. It is applicable to active and passive fishing gear.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 139, Textiles — Standard atmospheres for conditioning and testing
ISO 1107, Fishing nets — Netting — Basic terms and definitions
IEC 60529, Degrees of protection provided by enclosures (IP Code)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
active fishing gear
fishing gear requiring movement to catch the fish
NOTE In general, mobile fishing equipment (i.e. equipment which is mobile relative to the sea bed or to the water) is
led into the path of the fish to pursue and catch them. All trawls, dredges, seine nets, purse seines and other surrounding
nets are examples of active gear.
3.2
trawl
towed net consisting of a cone-shaped body closed at the rear by a bag or cod end and widened at the
opening by wings
NOTE A trawl may be towed by one or two boats and, depending on the type, is used on the bottom or as a midwater
(pelagic) trawl.
3.3
Danish seine
funnel-shaped net (with wings and cod end) with very long ropes laid out on the sea bed and hauled in to a
vessel in the open sea
ISO 16663-1:2009(E)
3.4
purse seine
large single-panel multisection net used to encircle pelagic fish, the bottom of the net being drawn together to
enclose the encircled fish
3.5
passive fishing gear
fishing gear requiring movement of the fish in order for the fish to be caught
NOTE This gear is usually stationary equipment, often, but not always, anchored on the sea bed. Gill nets and
entangling nets are examples of passive gear.
3.6
gill net
panel of netting, usually of rectangular shape, made of thin twine or monofilament yarn, in the meshes of
which the fish are caught
NOTE The net is suspended vertically in the water by floats and sinkers.
3.7
entangling net
loosely hung vertical net that catches fish by entangling rather than enmeshing them
3.8
trammel net
bottom-set net which is made up of of three walls of netting, the two tightly hung outer walls having a larger
mesh size than the inner wall which is loosely hung between them
NOTE The fish pass through one of the outer walls and become entangled in the small meshes of the inner wall, after
which they push themselves into the second outer wall, thus forming a bag.
4 Principle
An objective mesh gauge is inserted into the mesh opening. The mesh is stretched by a movable jaw until a
pre-set measurement force is reached. The size of the mesh opening is then measured automatically.
5 Apparatus
5.1 Objective mesh gauge, complying with the requirements of 5.1.1 to 5.1.6.
5.1.1 The objective mesh gauge used for determining mesh openings shall be automatic and electrically
driven (see Figure 1). The gauge shall be able to apply selected longitudinal measuring forces, in the range
5 N to 180 N, to the meshes with a precision of 1 N. Fixed measuring forces of 10 N, 20 N, 50 N and 125 N
shall be provided. A built-in system for measuring the applied force is needed. The gauge shall have two jaws,
one fixed and one movable, each 2 mm thick with rounded edges with a radius of 1 mm, to ensure that the
jaws slip easily over the twine or yarn. A mesh shall be stretched at a constant speed of (300 ± 30) mm/min by
the movable jaw. The gauge shall be able to measure meshes from 10 mm to 300 mm and may have different,
detachable, jaws for use on small and large meshes. The measurement precision shall be 1 mm.
5.1.2 The structure of the gauge shall be rigid and shall not distort under load. The body shall be light yet
robust
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.