EN ISO 7326:2008

SLOVENSKI STANDARD
01-maj-2008
1DGRPHãþD
SIST EN 27326:2000
*XPHQHLQSROLPHUQHFHYL2FHQDRGSRUQRVWLSURWLR]RQXSULVWDWLþQLKSRJRMLK
,62
Rubber and plastics hoses - Assessment of ozone resistance under static conditions
(ISO 7326:2006)
Gummi- und Kunststoffschläuche - Bestimmung der Ozonbeständigkeit unter statischen
Bedingungen (ISO 7326:2006)
Tuyaux en caoutchouc et en plastique - Évaluation de la résistance à l'ozone dans des
conditions statiques (ISO 7326:2006)
Ta slovenski standard je istoveten z: EN ISO 7326:2008
ICS:
23.040.70
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 7326
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2008
ICS 23.040.70 Supersedes EN 27326:1993
English Version
Rubber and plastics hoses - Assessment of ozone resistance
under static conditions (ISO 7326:2006)
Tuyaux en caoutchouc et en plastique - Évaluation de la Gummi- und Kunststoffschläuche - Bestimmung der
résistance à l'ozone dans des conditions statiques (ISO Ozonbeständigkeit unter statischen Bedingungen (ISO
7326:2006) 7326:2006)
This European Standard was approved by CEN on 7 February 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7326:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
The text of ISO 7326:2006 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber
products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
7326:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2008, and conflicting national standards shall be withdrawn at
the latest by August 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 27326:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 7326:2006 has been approved by CEN as a EN ISO 7326:2008 without any modification.

INTERNATIONAL ISO
STANDARD 7326
Third edition
2006-10-01
Rubber and plastics hoses —
Assessment of ozone resistance under
static conditions
Tuyaux en caoutchouc et en plastique — Évaluation de la résistance à
l'ozone dans des conditions statiques

Reference number
ISO 7326:2006(E)
©
ISO 2006
ISO 7326:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved

ISO 7326:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 General considerations. 1
4 Apparatus . 2
5 Test pieces . 2
5.1 Type of test piece. 2
5.2 Number of test pieces . 3
6 Conditioning of test pieces. 3
7 Test conditions . 3
8 Procedure . 3
8.1 Method 1 . 3
8.2 Method 2 . 4
8.3 Method 3 . 4
8.4 Method 4 . 5
8.5 Method 5 . 6
9 Test report . 7

ISO 7326:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsibl
...