Gas welding equipment - Air-aspirated hand blowpipes - Specifications and tests (ISO 9012:2008)

ISO 9012:2008 specifies requirements and test methods for air-aspirated hand blowpipes.
ISO 9012:2008 applies to blowpipes for brazing, soldering, heating, fusion and other allied thermal processes, which use a fuel gas and aspirated air (injector-type blowpipes), and are intended for manual use.
ISO 9012:2008 is applicable to: air-aspirated hand blowpipes which are fed with a fuel gas in the gaseous phase, at a controlled pressure by a regulator, through a gas supply hose; air-aspirated hand blowpipes which are fed with a liquefied fuel gas in the gaseous phase at the container pressure, through a gas supply hose; so-called liquid-phase blowpipes which are fed with a fuel gas in the liquid phase, and where thermal evaporation takes place within the blowpipe.

Gasschweißgeräte - Handbrenner für angesaugte Luft - Anforderungen und Prüfungen (ISO 9012:2008)

Diese Internationale Norm legt Anforderungen und Prüfverfahren für Handbrenner für angesaugte Luft fest.
Diese Internationale Norm gilt für Brenner zum Hartlöten, Weichlöten, Wärmen, Schmelzen und für ähnliche thermische Verfahren, die mit Brenngas und angesaugter Luft betrieben worden (Düsenbrenner) und dazu eingerichtet sind, von Hand geführt zu werden.
Diese Internationale Norm gilt für:
- Handbrenner für angesaugte Luft, denen das Brenngas durch einen Brenngasschlauch mit einem bestimmten, durch Regler einstellbaren Druck in gasförmigem Zustand zugeleitet wird;
- Handbrenner für angesaugte Luft, denen Flüssiggas durch einen Brenngasschlauch mit dem im Behälter herrschenden Druck in gasförmigem Zustand zugeleitet wird;
- sogenannte Flüssiggasverdampfungsbrenner, denen Flüssiggas in flüssigem Zustand zugeleitet wird und bei denen thermisches Verdampfen innerhalb des Brenners erfolgt.
Sie gilt nicht für Brenner, bei denen das Brenngas in flüssiger Phase an der Düse austritt. Sie gilt ebenfalls nicht für sogenannte Kartuschenbrenner, bei denen der Brenngasbehälter (die Kartusche) unmittelbar mit dem Brenner verbunden ist und gegebenenfalls als Griffstück dient.
ANMERKUNG Bild 1 bis Bild 4 in dieser Internationalen Norm dienen lediglich der Erläuterung und einem besseren Verständnis der Begriffserklärungen. Es werden keine Einzelheiten der Konstruktion vorgeschrieben, diese bleiben dem Hersteller überlassen.

Équipement de soudage aux gaz - Chalumeaux manuels aéro-gaz à air aspiré - Spécifications et essais (ISO 9012:2008)

L'ISO 9012:2008 spécifie les exigences et les méthodes d'essai des chalumeaux manuels aéro-gaz à air aspiré.
L'ISO 9012:2008 s'applique aux chalumeaux destinés au brasage fort, au brasage tendre, au chauffage, à la fusion et aux autres procédés thermiques similaires, utilisant un gaz combustible et de l'air aspiré (chalumeau à air induit), conçus pour une utilisation manuelle.
L'ISO 9012:2008 s'applique également aux chalumeaux manuels aéro-gaz à air aspiré, alimentés par un gaz combustible en phase gazeuse, sous une pression régulée par un détendeur, à travers un tuyau d'amenée de gaz, aux chalumeaux manuels aéro-gaz à air aspiré, alimentés par un gaz combustible liquéfié en phase gazeuse sous la pression du réservoir, à travers un tuyau d'amenée de gaz et aux chalumeaux dits à phase liquide, alimentés par un gaz combustible en phase liquide et dans lesquels se produit une évaporation thermique.

Oprema za plamensko varjenje - Ročni gorilniki z vsesavanjem zraka - Popisi in preskusi (ISO 9012:2008)

ISO 9012:2008 določa zahteve za preskusne metode za ročne gorilnike z vsesavanjem zraka.
ISO 9012:2008 velja za gorilnike za trdo spajkanje, spajkanje, ogrevanje, spajanje in druge sorodne termične procese, ki uporabljajo kurilni plin in vsesani zrak (gorilniki injektorskega tipa) in so namenjeni ročni uporabi.
ISO 9012:2008 velja za: ročne gorilnike z vsesavanjem zraka, ki se napajajo s kurilnim plinom v plinski fazi pri tlaku, nadzorovanem z regulatorjem, prek cevi za plinsko oskrbo; ročne gorilnike z vsesavanjem zraka, ki se napajajo z utekočinjenim kurilnim plinom v plinski fazi pri tlaku vsebnika prek cevi za plinsko oskrbo; t. i. gorilnike na tekočo fazo, ki se napajajo s kurilnim plinom v tekoči fazi in pri katerih znotraj gorilnika poteka termično izparevanje.

General Information

Status
Withdrawn
Publication Date
04-Oct-2011
Withdrawal Date
24-Oct-2023
Current Stage

Relations

Buy Standard

Standard
EN ISO 9012:2011
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2011
1DGRPHãþD
SIST EN 731:1997
2SUHPD]DSODPHQVNRYDUMHQMH5RþQLJRULOQLNL]YVHVDYDQMHP]UDND3RSLVLLQ
SUHVNXVL ,62
Gas welding equipment - Air-aspirated hand blowpipes - Specifications and tests (ISO
9012:2008)
Gasschweißgeräte - Handbrenner für angesaugte Luft - Anforderungen und Prüfungen
(ISO 9012:2008)
Équipement de soudage aux gaz - Chalumeaux manuels aéro-gaz à air aspiré -
Spécifications et essais (ISO 9012:2008)
Ta slovenski standard je istoveten z: EN ISO 9012:2011
ICS:
25.160.30 Varilna oprema Welding equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 9012
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2011
ICS 25.160.30 Supersedes EN 731:1995
English Version
Gas welding equipment - Air-aspirated hand blowpipes -
Specifications and tests (ISO 9012:2008)
Équipement de soudage aux gaz - Chalumeaux manuels Gasschweißgeräte - Handbrenner für angesaugte Luft -
aéro-gaz à air aspiré - Spécifications et essais (ISO Anforderungen und Prüfungen (ISO 9012:2008)
9012:2008)
This European Standard was approved by CEN on 18 September 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9012:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 9012:2008 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
9012:2011 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 731:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 9012:2008 has been approved by CEN as a EN ISO 9012:2011 without any modification.

INTERNATIONAL ISO
STANDARD 9012
Third edition
2008-02-15
Gas welding equipment — Air-aspirated
hand blowpipes — Specifications and
tests
Équipement de soudage aux gaz — Chalumeaux manuels aéro-gaz à
air aspiré — Spécifications et essais

Reference number
ISO 9012:2008(E)
©
ISO 2008
ISO 9012:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved

ISO 9012:2008(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Main types of aspiration. 2
5 Description of components . 5
5.1 Shank or handle . 5
5.2 Attachment . 5
5.3 Self-closing on/off valve control . 6
5.4 Device to prevent inadvertent operation. 6
6 Requirements . 6
6.1 General. 6
6.2 Materials . 6
6.3 Valves. 6
6.4 Shank . 6
6.5 Hose connection. 7
6.6 Gas tightness . 7
6.7 Gas-flow rate . 7
6.8 Safety against sustained backfiring and blowing-off of the flame . 7
6.9 Flame adjustment . 7
6.10 Stability in air currents. 7
6.11 Ignition . 8
7 Tests. 8
7.1 General. 8
7.2 General checks . 8
7.3 Operational tests. 8
7.4 Shank-overheating tests . 8
7.5 Gas tightness . 8
7.6 Valve endurance test. 9
7.7 Checking gas-flow rates . 9
7.8 Safety against sustained backfire and blowing-off of the flame . 9
7.9 Stability in air currents. 9
7.10 Verification of the device against inadvertent operation. 9
8 Marking . 9
8.1 General. 9
8.2 Marking of the shank. 10
8.3 Marking of the attachment . 10
9 Code letters identifying the gas(es) used . 10
10 Instructions for use . 10
Bibliography . 12

ISO 9012:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9012 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 8, Equipment for gas welding, cutting and allied processes.
This third edition cancels and replaces the second edition (ISO 9012:1998), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 8 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
iv © ISO 2008 – All rights reserved

INTERNATIONAL STANDARD ISO 9012:2008(E)

Gas weldin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.