EN 4500-005:2012

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VWDYOMDQMHLuft- und Raumfahrt - Metallische Werkstoffe - Regeln für das Erstellen und die Gestaltung von Werkstoffnormen - Teil 005: Besondere Regeln für StähleSérie aérospatiale - Matériaux métalliques - Règles pour la rédaction et la présentation des normes de matériaux - Partie 005: Règles spécifiques aux aciersAerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 005: Specific rules for steels49.025.10JeklaSteelsICS:Ta slovenski standard je istoveten z:EN 4500-005:2012SIST EN 4500-005:2014en01-marec-2014SIST EN 4500-005:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4500-005
October 2012 ICS 49.025.10 English Version
Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 005: Specific rules for steels
Série aérospatiale - Matériaux métalliques - Règles pour la rédaction et la présentation des normes de matériaux - Partie 005: Règles spécifiques aux aciers
Luft- und Raumfahrt - Metallische Werkstoffe - Regeln für das Erstellen und die Gestaltung von Werkstoffnormen - Teil 005: Besondere Regeln für Stähle This European Standard was approved by CEN on 23 June 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4500-005:2012: ESIST EN 4500-005:2014

See EN 4500-001 and Example 3 of this standard. 4.4.21 Page 4, line 20: Impact strength See EN 4500-001 and Example 3 of this standard. 4.4.22 Page 4, lines 21 to 26: Creep (C) See EN 4500-001 and Example 3 of this standard. SIST EN 4500-005:2014

Aerospace series Steel 100Cr6 (1.3505) Air melted Annealed Bar for machining D ≤ 100 mm 900 MPa ≤ Rm ≤ 1 100 MPa
Série aérospatiale Acier 100Cr6 (1.3505) Élaboré à l'air Recuit Barres pour usinage D ≤ 100 mm 900 MPa ≤ Rm ≤ 1 100 MPa Luft-und Raumfahrt Stahl 100Cr6 (1.3505) Lufterschmolzen Geglüht Stangen zur spanenden Bearbeitung D ≤ 100 mm 900 MPa ≤ Rm ≤ 1 100 MPa
100C6,
AECMA: FE-PL 31,
ASD STAN: FE-PL 1801. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4258, Aerospace series — Metallic materials — General organization of standardization — Links between types of EN standards and their use EN 4500-005, Aerospace series — Metallic materials — Rules for drafting and presentation of material standards — Part 005: Specific rules for steel EN 4700-001, Aerospace series — Steel and heat resisting alloys — Wrought products — Technical specification — Part 001: Plate, sheet and strip
6.1 Delivery condition Annealed Solution treated Heat treatment 800 °C ≤ θ ≤ 850 °C 100 °C ≤ θ ≤ 1 050 °C / t ≥ 30 min WQ or AQ 6.2 Delivery condition code A U 7 Use condition Solution treated Delivery condition Heat treatment Delivery condition + 1 000 °C ≤ θ ≤ 1 050 °C / t ≥ 30 min WQ or AQ –
Characteristics 8.1 Test sample(s) EN 4700-
...