EN 3001:2019

SLOVENSKI STANDARD
01-september-2019
Aeronavtika - Utrjene plavajoče steklene plošče za uporabo v zrakoplovih -
Tehnična specifikacija
Aerospace series - Tempered float glass plies for aircraft applications - Technical
specification
Luft- und Raumfahrt - Vorgespannte Floatglasscheiben für Luftfahrzeuganwendungen -
Technische Lieferbedingungen
Série aérospatiale - Plis de verre renforcés pour applications aéronautiques -
Spécification technique
Ta slovenski standard je istoveten z: EN 3001:2019
ICS:
49.045 Konstrukcija in konstrukcijski Structure and structure
elementi elements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 3001
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 49.045
English Version
Aerospace series - Tempered float glass plies for aircraft
applications - Technical specification
Série aérospatiale - Plis de verre renforcés pour Luft- und Raumfahrt - Vorgespannte Floatglasscheiben
applications aéronautiques - Spécification technique für Luftfahrzeuganwendungen - Technische
Lieferbedingungen
This European Standard was approved by CEN on 14 January 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3001:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Required characteristics . 5
5 Quality assurance . 8
6 Storage and packing . 8
7 Marking . 8
8 Ordering . 8

European foreword
This document (EN 3001:2019) has been prepared by the Aerospace and Defence Industries Association
of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards shall
be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
1 Scope
This document specifies the requirements for tempered soda-lime float glass plies which are made from
annealed glass either of the universally available type or of high light transmission type. The annealed
glass is manufactured by a continuous process for general use.
The plies are tempered by either a thermal or chemical process.
The tempered glass is used mainly for cockpit glazing.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2155-5, Aerospace series — Test methods for transparent materials for aircraft glazing — Part 5:
Determination of visible light transmission
EN 2155-6, Aerospace series — Test methods for transparent materials for aircraft glazing —Part 6:
1)
Determination of optical defects
EN 2155-8, Aerospace series — Test methods for transparent materials for aircraft glazing — Part 8:
Determination of optical distortion
EN 2155-9, Aerospace series — Test methods for transparent materials for aircraft glazing — Part 9:
Determination of haze
EN 9133, Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace
Standard Products
EN 3861, Aerospace series — Non-metallic materials — Glass transparencies — Material standard —
Thermally tempered soda lime float glass
EN 3862, Aerospace series — Non-metallic materials — Glass transparencies — Material standard —
Chemically tempered soda lime float glass
EN 3863, Aerospace series — Non-metallic materials — Glass transparencies — Test methods —
Determination of flatness
EN 3864, Aerospace series — Non-metallic materials — Glass transparencies — Test methods —
Determination of modulus of rupture
2)
EN 3865, Aerospace series — Stress/optical measurement of tempered glass — Test method
EN 3866, Aerospace series — Non-metallic materials — Glass transparencies — Test methods —
Determination of ream and surface ripple

1) Published as ASD-STAN Prestandard at the date of publication of this standard by AeroSpace and Defence industries
Association of Europe - Standardization (ASD-STAN) (http://www.asd-stan.org/)
2) In preparation at the date of publication of this standard.
EN ISO
...