EN 294:1992/AC:1993
(Corrigendum)Safety of machinery - Safety distance to prevent danger zones being reached by the upper limbs
- BACK
- 26-Jan-1993
- 04-Mar-2008
- 13.110
- 98/37/EC
- M/BC/CEN/88/13
- CEN/TC 114
Safety of machinery - Safety distance to prevent danger zones being reached by the upper limbs
Sicherheit von Maschinen - Sicherheitsabstände gegen das Erreichen von Gefahrstellen mit den oberen Gliedmaßen
Sécurité des machines - Distances de sécurité pour empêcher l'atteinte des zones dangereuses par les membres supérieurs
Varnost strojev - Varnostne razdalje, ki preprečujejo doseg nevarnih območij z zgornjimi udi - Popravek AC
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 294:1997/AC:2003
01-julij-2003
9DUQRVWVWURMHY9DUQRVWQHUD]GDOMHNLSUHSUHþXMHMRGRVHJQHYDUQLKREPRþLM]
]JRUQMLPLXGL3RSUDYHN$&
Safety of machinery - Safety distance to prevent danger zones being reached by the
upper limbs
Sicherheit von Maschinen - Sicherheitsabstände gegen das Erreichen von Gefahrstellen
mit den oberen Gliedmaßen
Sécuri
...
This May Also Interest You
This document addresses how artificial intelligence machine learning can impact the safety of machinery and machinery systems.
This document describes how hazards being associated with artificial intelligence (AI) applications machine learning in machinery or machinery systems, and designed to act within specific limits, can be considered in the risk assessment process.
This document is not applicable to machinery or machinery systems with AI applications machine learning designed to act beyond specified limits that can result in unpredictable effects.
This document does not address safety systems with AI, for example, safety-related sensors and other safety-related parts of control systems.
- Technical report14 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-Apr-2022
- 13.110
- CEN/TC 114
This document provides assistance to the designer/manufacturer of machinery and related components as to how the system of existing type-A, type-B and type-C machinery safety standards should be applied in order to design a machine to achieve a level of tolerable risk by adequate risk reduction.
This document explains the general principles of ISO 12100 and how this type-A standard is used for practical cases in conjunction with type-B and type-C machinery safety standards.
This document provides assistance to standards-writing committees on how ISO 12100 and type-B and type-C standards relate and explains their function in the risk assessment and risk reduction process according to ISO 12100.
This document includes an overview of existing categories of type-B standards to assist standards readers and writers to navigate the many standards.
- Technical report25 pagesEnglish languagesale 10% offe-Library read for×1 day
- 09-Feb-2021
- 13.110
- CEN/TC 114
This document gives machine manufacturers guidance on potential security aspects in relation to safety of machinery when putting a machine into service or placing on the market for the first time. It provides essential information to identify and address IT-security threats which can influence safety of machinery.
This document gives guidance but does not provide detailed specifications on how to address IT-security aspects which can influence safety of machinery.
This document does not address the bypass or defeat of risk reduction measures through physical manipulation.
- Technical report23 pagesEnglish languagesale 10% offe-Library read for×1 day
- 07-Apr-2020
- 13.110
- CEN/TC 114
This document establishes values for safety distances in both industrial and non-industrial environments to prevent machinery hazard zones being reached. The safety distances are appropriate for protective structures. It also gives information about distances to impede free access by the lower limbs (see Annex B).
This document covers people of 14 years and older (the 5th percentile stature of 14-year-olds is approximately 1 400 mm). In addition, for upper limbs only, it provides information for children older than 3 years (5th percentile stature of 3-year-olds is approximately 900 mm) where reaching through openings needs to be addressed.
NOTE 1 It is not practical to specify safety distances for all persons. Therefore, the values presented are intended to cover the 95th percentile of the population.
Data for preventing lower limb access for children is not considered.
The distances apply when sufficient risk reduction can be achieved by distance alone. Because safety distances depend on size, some people of extreme dimensions will still be able to reach hazard zones even when the requirements of this document are met.
Compliance with the requirements in this document will prevent access to the hazard zone. Nevertheless the user of this document is advised that it does not provide the required risk reduction for every hazard (e.g. hazards related to machine emissions such as ionizing radiation, heat sources, noise, dust).
The clauses covering lower limbs apply on their own only when access by the upper limbs to the same hazard zone is not foreseeable according to the risk assessment.
The safety distances are intended to protect those persons trying to reach hazard zones under the conditions specified (see 4.1.1).
NOTE 2 This document is not intended to provide measures against reaching a hazard zone by climbing over (see ISO 14120:2015, 5.18).
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft26 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Jan-2020
- 29-Apr-2020
- 13.110
- 2006/42/EC
- M/396
- CEN/TC 114
ISO 13854:2017 enables the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. It specifies minimum gaps relative to parts of the human body and is applicable when adequate safety can be achieved by this method.
ISO 13854:2017 is applicable to risks from crushing hazards only and is not applicable to other possible hazards, e.g. impact, shearing, drawing-in.
NOTE For impact, shearing, drawing-in hazards, additional or other measures are to be taken.
- Standard15 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Dec-2019
- 30-Mar-2020
- 13.110
- 2006/42/EC
- M/079
- M/396
- CEN/TC 114
This document specifies requirements for the machine manufacturer for preparation of the safety-relevant parts of an instruction handbook for machinery.
This document:
— provides further specifications to the general requirements on information for use given in ISO 12100:2010, 6.4.5; and
— deals with the safety-related content, the corresponding structure and presentation of the instruction handbook, taking into account all phases of the life cycle of the machine.
NOTE 1 The strategy for risk reduction at the machine is given in ISO 12100:2010, Clause 6, and includes inherently safe design measures, safeguarding and complementary risk reduction measures as well as information for use.
NOTE 2 Annex A contains a correspondence table between ISO 12100:2010, 6.4, and this document.
NOTE 3 Information for conception and preparation of instructions in general is available in IEC/IEEE 82079-1.
This document establishes the principles which are indispensable to provide information on residual risks.
This document does not address requirements for declaration of noise and vibration emissions.
This document is not applicable to machinery manufactured before the date of its publication.
- Standard34 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Oct-2019
- 30-Jan-2020
- 13.110
- 2006/42/EC
- M/396
- CEN/TC 114
This document specifies the safety requirements of a two-hand control device (THCD) and the dependency of the output signal from the actuation by hand of the control actuating devices.
This document describes the main characteristics of THCDs for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hold-to-run devices or as special control devices.
This document does not specify with which machines THCDs shall be used. It also does not specify which types of two-hand-control device shall be used for a specific application. Moreover, while guidance is given, it does not specify the required distance between the THCD and the danger zone (see 8.8).
This document provides requirements for design and guidance on the selection (based on a risk assessment) of THCDs including the prevention of defeat, the avoidance of faults and verification of compliance.
NOTE 1 A THCD only offers protection for the person using it.
NOTE 2 For specific machines, the suitability of a two-hand control as a suitable protective device can be defined in a type-C standard. If such a standard does not exist or is not appropriate, the risk assessment and determination of suitable protective measures is the responsibility of the manufacturer of the machine.
This document applies to all THCDs, independent of the energy used, including:
— THCDs which are fully assembled for installation;
— THCDs which are assembled by the machine manufacturer or integrator.
This document is not applicable to THCDs manufactured before the date of its publication.
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft24 pagesEnglish languagesale 10% offe-Library read for×1 day
- 16-Apr-2019
- 30-Oct-2019
- 13.110
- 2006/42/EC
- M/396
- CEN/TC 114
This document specifies methods for identifying fire hazards resulting from machinery and for performing a risk assessment.
It gives the basic concepts and methodology of protective measures for fire prevention and protection to be taken during the design and construction of machinery. The measures consider the intended use and reasonably foreseeable misuse of the machine.
It provides guidelines for consideration in reducing the risk of machinery fires to acceptable levels through machine design, risk assessment and operator instructions.
This document is not applicable to:
— mobile machinery;
— machinery designed to contain controlled combustion processes (e.g. internal combustion engines, furnaces), unless these processes can constitute the ignition source of a fire in other parts of the machinery or outside of this;
— machinery used in potentially explosive atmospheres and explosion prevention and protection; and
— fire detection and suppression systems that are integrated in building fire safety systems.
It is also not applicable to machinery or machinery components manufactured before the date of its publication.
- Standard59 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-Feb-2019
- 30-Aug-2019
- 13.110
- 13.220.40
- 2006/42/EC
- M/396
- CEN/TC 114
ISO 14118:2017 specifies requirements for designed-in means aimed at preventing unexpected machine start-up (see 3.2) to allow safe human interventions in danger zones (see Annex A).
ISO 14118:2017 applies to unexpected start-up from all types of energy source, i.e.:
- power supply, e.g. electrical, hydraulic, pneumatic;
- stored energy due to, e.g. gravity, compressed springs;
- external influences, e.g. from wind.
ISO 14118:2017 does not specify performance levels or safety integrity levels for safety-related parts of control systems. While available means to prevent unexpected start-up are identified, this document does not specify the means for the prevention of unexpected machine start-up for specific machines.
NOTE A type-C standard can define the required means for the prevention of harm arising from unexpected start-up. Otherwise, the requirements for a specific machine need to be determined by risk assessment outside the scope of this document.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft15 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2018
- 30-Aug-2018
- 13.110
- 2006/42/EC
- M/079
- M/396
- CEN/TC 114
ISO 14122-3:2016 gives requirements for non-powered stairs, stepladders and guard-rails which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of those fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-3:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. stairs, stepladders, guard-rails) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine.
NOTE 2 Where no local regulation or standards exists, this part of ISO 14122 may be used also for means of access which are outside the scope of the standard.
It is intended that this part of ISO 14122 be used with ISO 14122‑1 to give the requirements for steps, stepladders and guard-rails.
The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.
ISO 14122-3:2016 is not applicable to machinery manufactured before the date of its publication.
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft25 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Sep-2016
- 30-Dec-2016
- 13.110
- 2006/42/EC
- M/396
- M/BC/CEN/88/13
- CEN/TC 114
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.