EN ISO 15976:2002

SLOVENSKI STANDARD
SIST EN ISO 15976:2003
01-julij-2003
Slepe polne kovice z zarezanim zakovnim trnom in zaobljeno valjasto glavo - St/St
(ISO 15976:2002)
Closed end blind rivets with break pull mandrel and protrudiing head - St/St (ISO
15976:2002)
Geschlossene Blindniete mit Sollbruchdorn und Flachkopf - St/St (ISO 15976:2002)
Rivets aveugles a rupture de tige a corps fermé, a tete bombée - St/St (ISO 15976:2002)
Ta slovenski standard je istoveten z: EN ISO 15976:2002
ICS:
21.060.40 Kovice Rivets
SIST EN ISO 15976:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15976:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 15976:2003
EUROPEAN STANDARD
EN ISO 15976
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 21.060.40
English version
Closed end blind rivets with break pull mandrel and protrudiing
head - St/St (ISO 15976:2002)
Rivets aveugles à rupture de tige à corps fermé, à tête Geschlossene Blindniete mit Sollbruchdorn und Flachkopf -
bombée - St/St (ISO 15976:2002) St/St (ISO 15976:2002)
This European Standard was approved by CEN on 14 October 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15976:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15976:2003
EN ISO 15976:2002 (E)
CORRECTED  2002-12-18
Foreword
This document (EN ISO 15976:2002) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2003, and conflicting national standards
shall be withdrawn at the latest by May 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15976:2002 has been approved by CEN as EN ISO 15976:2002 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15976:2003
EN ISO 15976:2002 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 3269 2000 Fasteners - Acceptance EN ISO 3269 2000
inspection
ISO 4042 1999 Fasteners - Electroplated coatings EN ISO 4042 1999
ISO 14588 2000 Blind rivets - Terminology and EN ISO 14588 2000
definitions
ISO 14589 2000 Blind rivets - Mechanical testing EN ISO 14589 2000
3

---------------------- Page: 5 ----------------------

SIST EN ISO 15976:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 15976:2003


INTERNATIONAL ISO
STAND
...