EN ISO 8666:2018

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 8666:2016
Mala plovila - Osnovni podatki (ISO 8666:2016)
Small craft - Principal data (ISO 8666:2016)
Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)
Petits navires - Données principales (ISO 8666:2016)
Ta slovenski standard je istoveten z: EN ISO 8666:2018
ICS:
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 8666
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 8666:2016
English Version
Small craft - Principal data (ISO 8666:2016)
Petits navires - Données principales (ISO 8666:2016) Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8666:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
The text of ISO 8666:2016 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 8666:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8666:2016.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 8666:2016 has been approved by CEN as EN ISO 8666:2018 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Article 3 and Annex I of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub- Remarks/Notes
Directive 2013/53/EU clause(s) of
this EN
Article 3(10) – Definitions - 4.2.1, 4.2.3, 7.3 - ‘Hull length’ means the length of hull measured
‘Hull length’ in accordance with the harmonised standard.
This standard establishes the methodology for
measuring the length of hull L .
H
Annex I, Part A, 2 GENERAL
REQUIREMENTS
Annex I, Part A, 2.2 (d) – 5.6 The Standard establishes the definition for
Watercraft builder’s plate “maximum load m ”. This is to be understood
ML
as the “manufacturer's recommended maximum

load” in accordance with EN ISO 14946.
Annex I, Part A, 3 INTEGRITY
AND STRUCTURAL
REQUIREMENTS
Annex I, Part A, 3.1 - Structure 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
dimensions and related data, mass
specifications and loading conditions that are
required for determining hull construction and
scantlings derived from EN ISO 12215.
Annex I, Part A, 3.2 - Stability 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
and freeboard dimensions and related data, mass

specifications and loading conditions that are
required for evaluating the stability and
buoyancy of intact (i.e. undamaged) boats in
accordance with EN ISO 12217 in order to
assign a design category appropriate to the
design and maximum load.
Annex I, Part A, 3.3 – Buoyancy 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
and floatation dimensions and related data, mass

specifications and loading conditions that are
required for evaluating the flotation
characteristics of boats susceptible to swamping
and the requirements for inverted buoyancy in
accordance with EN ISO 12217.
Annex I, Part A, 3.4 - Flooding 4.2.3, 4.3.2, In respect of dimensions for calculating the
4.4.3.3 cockpit volume coefficient in accordance with
EN ISO 12216.
Annex I, Part A, 3.6 - 5.6 The Standard establishes the definition for
Manufacturer’s maximum “maximum load m ”. This is to be understood
ML
recommended load as the “manufacturer's recommended maximum
load” in accordance with EN ISO 14946.
Annex I, Part A, 5
INSTALLATION
REQUIREMENTS
Annex I, Part A, 5.4.2 – Steering 2.8, 2.9 The Standard establishes definitions for a
systems -Emergency “sailing craft” and a “non-sailing craft”.
arrangements for sailing
These definitions shall be used wherever
recreational craft and single-
required for the application of the essential
propulsion engine non-sailing
requirements set out in Annex I of Directive
recreational craft
2013/53/EU.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 8666
Second edition
2016-07-01
Small craft — Principal data
Petits navires — Données principales
Reference number
ISO 8666:2016(E)
©
ISO 2016
ISO 8666:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 8666:2016(E)
Contents Page
Foreword .v
1 Scope . 1
2 Terms and definitions . 1
3 Symbols, designations and units . 2
4 Measurements . 3
4.1 General . 3
4.2 Longitudinal . 4
4.2.1 General. 4
4.2.2 Maximum length, L .
max 4
4.2.3 Length of the hull, L .
H 4
4.2.4 Waterline length, L .
WL 7
4.3 Athwartship . 8
4.3.1 General. 8
4.3.2 Maximum beam, B .
max 8
4.3.3 Beam of hull, B .
H 8
4.3.4 Beam, waterline, B .
WL 8
4.3.5 Maximum beam, waterline, B .
WLmax 8
4.3.6 Beam between hull centers, B .
CB 8
4.4 Vertical . 9
4.4.1 Maximum depth, D .
max 9
4.4.2 Midship depth, D .
LWL/2 9
4.4.3 Freeboard, F .10
4.4.4 Draught, T .10
4.4.5 Draught, air, H .
a 10
4.4.6 Headroom .11
4.5 Other data .
...