EN ISO 5832-1:2019

SLOVENSKI STANDARD
01-december-2019
Vsadki (implantati) za kirurgijo - Kovinski materiali - 1. del: Nerjavno jeklo (ISO
5832-1:2016)
Implants for surgery - Metallic materials - Part 1: Wrought stainless steel (ISO 5832-
1:2016)
Chirurgische Implantate - Metallische Werkstoffe - Teil 1: Nichtrostender Stahl (ISO 5832
-1:2016)
Implants chirurgicaux - Produits à base de métaux - Partie 1: Acier inoxydable corroyé
(ISO 5832-1:2016)
Ta slovenski standard je istoveten z: EN ISO 5832-1:2019
ICS:
11.040.40 Implantanti za kirurgijo, Implants for surgery,
protetiko in ortetiko prosthetics and orthotics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 5832-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 11.040.40
English Version
Implants for surgery - Metallic materials - Part 1: Wrought
stainless steel (ISO 5832-1:2016)
Implants chirurgicaux - Produits à base de métaux - Chirurgische Implantate - Metallische Werkstoffe - Teil
Partie 1: Acier inoxydable corroyé (ISO 5832-1:2016) 1: Nichtrostender Stahl (ISO 5832-1:2016)
This European Standard was approved by CEN on 2 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5832-1:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 5832-1:2016 has been prepared by Technical Committee ISO/TC 150 "Implants for
surgery” of the International Organization for Standardization (ISO) and has been taken over as
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 5832-1:2016 has been approved by CEN as EN ISO 5832-1:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 5832-1
Fifth edition
2016-07-15
Implants for surgery — Metallic
materials —
Part 1:
Wrought stainless steel
Implants chirurgicaux — Produits à base de métaux —
Partie 1: Acier inoxydable corroyé
Reference number
ISO 5832-1:2016(E)
©
ISO 2016
ISO 5832-1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 5832-1:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Chemical composition . 2
4.1 Test samples . 2
4.2 Cast analysis . 2
5 Microstructure in the fully annealed condition . 2
5.1 Grain size . 2
5.2 Microstructure . 2
5.3 Inclusion content. 3
6 Mechanical properties . 3
6.1 Test pieces . 3
6.2 Tensile test . 3
6.3 Gauge length . 3
7 Test methods . 3
Bibliography . 6
ISO 5832-1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any t
...